Novità
Michał Kozub
aggiunto un nuovo album fotografico.
aggiunto un nuovo album fotografico.
6 13 September, 05:42
Lenny V
That's a beautiful little tank! Great paintjob, how do you glue it together without ruining the paint?
That's a beautiful little tank! Great paintjob, how do you glue it together without ruining the paint?
14 September, 11:36
Michał Kozub
Thanks. I'm using Tamiya Extra Thin 87038. If not touched until it dry, it doesnt damage the paint too much. In that case, it was possible to paint inner surfaces and then glue avarything from outside.
Thanks. I'm using Tamiya Extra Thin 87038. If not touched until it dry, it doesnt damage the paint too much. In that case, it was possible to paint inner surfaces and then glue avarything from outside.
16 September, 05:45
Michał Kozub
The kit is detailed and includes PE parts in box. It would be a pity to not show it. But, tbh, its a little tricky in some points (like lower wheels trailers, tower interia - very thin parts and fragile). Generally it is very nice kit to build
The kit is detailed and includes PE parts in box. It would be a pity to not show it. But, tbh, its a little tricky in some points (like lower wheels trailers, tower interia - very thin parts and fragile). Generally it is very nice kit to build
18 September, 05:53
Rolf Rolf
aggiunto un nuovo album fotografico.
aggiunto un nuovo album fotografico.
34 immagini
Mig17AS Cuban frescoNuovo: 18 September, 05:52 1:48
Weathering really ties it together
Progetto: Mikoyan MiG-17AS 'Fresco-A'
13 24 August, 14:25
Loginthesand
vuole questo oggetto
vuole questo oggetto
RE/100
AMX-107 BAWOO Neo-Zeon Attack Use Prototype Transformable Mobile Suit Bandai 1:100
0210512-3500 (006) 2016 Nuovo stampo 18 September, 05:49
Steiner_76
Frage ist sind das nur Dateien für Leute, die ein 3D Drucker haben?
Frage ist sind das nur Dateien für Leute, die ein 3D Drucker haben?
Panzer IV
Road Wheel set - open hub cap for Gunze / Revell / DML (old tooling) Tankbrusher Scale Modeling 1:35
352409007 2024 Nuovo stampo Digitale: File di dati 3D18 September, 05:45
Goldman
aggiunto un nuovo album fotografico.
aggiunto un nuovo album fotografico.
12 immagini
Freightliner FLD WIP1:24
I built the base chassis 25 years ago. Checking it I don't see any major alignment issues. Had to clean many moulding li...
Progetto: Freightliner FLD 120
4 1 August, 04:59
Greg Baker
aggiunto un nuovo album fotografico.
aggiunto un nuovo album fotografico.
4 immagini
The Castafiore Emerald (Citroën Ami 6)Nuovo: 18 September, 05:27 1:72
Progetto: The Castafiore Emerald (Citroën Ami 6)
Scratchbuilt
25 19 June, 14:33
Greg Baker
First print mostly successful. I will need to rework the thickness of the walls and the support struts for the roof. Much too thin.
First print mostly successful. I will need to rework the thickness of the walls and the support struts for the roof. Much too thin.
19 June, 14:35
LucLuke B
3d printing, I wouldn't know where to start. Is the ami 6 a file you found online?
3d printing, I wouldn't know where to start. Is the ami 6 a file you found online?
19 June, 19:39
Greg Baker
I did find it online, but was a little disappointed with the quality. It required a lot (and will need more) work to be able to print it. I mainly have to increase the thickness of the rear trunk area. The strange overhang roof in the rear needs to be sturdier as well.
I did find it online, but was a little disappointed with the quality. It required a lot (and will need more) work to be able to print it. I mainly have to increase the thickness of the rear trunk area. The strange overhang roof in the rear needs to be sturdier as well.
19 June, 19:59
Greg Baker
The second printing went much better. I made a mistake though, I forgot to add the support to both sides of the rear roof struts. Luckily one side seems to be strong enough to hold everything, and with a little paint I don't think the thin part will be visible.
The second printing went much better. I made a mistake though, I forgot to add the support to both sides of the rear roof struts. Luckily one side seems to be strong enough to hold everything, and with a little paint I don't think the thin part will be visible.
20 June, 14:08
Greg Baker
Good timing. After a bit of a summer break spent watching football, olympics, and playing video games with my son... I just started back at the modelling desk. After clearing up a couple of other, smaller, Tintin-related projects, I'm almost ready to tackle this one again.
Good timing. After a bit of a summer break spent watching football, olympics, and playing video games with my son... I just started back at the modelling desk. After clearing up a couple of other, smaller, Tintin-related projects, I'm almost ready to tackle this one again.
21 August, 14:09
Greg Baker
With the Hawker Hart off the bench and on the shelf… I guess it's time to tackle this one again. Getting the colour right was tricky. I finally settled on a 10:5:1 ratio of Tamiya XF-2 White, X-14 Sky Blue and XF-18 Medium Blue. Not perfect, but close enough I think.
With the Hawker Hart off the bench and on the shelf… I guess it's time to tackle this one again. Getting the colour right was tricky. I finally settled on a 10:5:1 ratio of Tamiya XF-2 White, X-14 Sky Blue and XF-18 Medium Blue. Not perfect, but close enough I think.
18 September, 05:30
DIEGO BRITOS
possiede questo oggetto
possiede questo oggetto
Messerschmitt Me P.1099B Heavy Armour / Schwerer Jäger
Revell 1:72
04359 (80-4359) 2010 Nuove decalcomanie 18 September, 05:28
/it/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=it
35
35
/it/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo