CL-415 MP MMEA

1
August 21, 2023
C-FWLK is the subject of choice. Are there easier to paint schemes? Sure... But this is irresistible.
2
August 21, 2023
The shape of the engine nacelles is not very accurate, the exhaust should be almost 2mm lower. It may seem little but in this scale is a noticeable difference.
3
August 21, 2023
The drawing above is the reference blueprint I hand copied from my phone screen. I removed the upper back part of the original piece and glued some styrene strips to add some bulk.
4
August 21, 2023
After some sanding.
5
August 21, 2023
Some new cockpit details as per reference pics.
6
August 21, 2023
7
August 21, 2023
Fuselage openings and interior parts finished.
8
August 21, 2023
The engraving of the water release hatches was not very consistent among fuselage sides, so I decided to drill them out and model new doors, thus adding some extra detail to the keel area.
9
August 21, 2023
10
August 21, 2023
Some painting going on
11
August 21, 2023
12
August 21, 2023
Painted cockpit
13
August 21, 2023
14
August 21, 2023
Surveillance equipment and water tank.
15
August 21, 2023
I didn't find any interior pics of this particular aircraft, but there's an advertising video from Canadair on Youtube with some glimpses of the SAR version, which I captured and used as reference.
16
August 21, 2023
Video screenshot
17
August 21, 2023
18
August 21, 2023
Cockpit and surveillance post seats.
19
August 21, 2023
Circuit breakers panels
20
August 21, 2023
Electrical equipment finished...
21
August 21, 2023
...and painted.
22
August 21, 2023
The floor was primed black and painted with light gray in a gradient, simulating light coming through the opened doors and getting darker towards the middle and back areas.
23
September 3, 2023
Still a cabrio, but not for long
24
September 3, 2023
Transparent part ready with new roof detail
25
September 3, 2023
Starboard side. Tried some nano writing too. The fact that it would never be seen again gave me some confidence 😉
26
September 3, 2023
Enjoying my stay at Rivet Hotel
27
September 3, 2023
Some extra detail added to the engine nacelles, not much left till I call them done.
28
August 21, 2023
The fit of fhe kit is really good, but the wing surface is not smooth and needed some puttying and sanding. The vortex generators are now gone.
29
September 3, 2023
After neverending sand-fill iterations the wing surface is now even and smooth. I fully rescribed it and added lots of removable panels on top that will hopefully improve the look of this bird from above. The kit lacks this kind of details, but it's great in terms of overall fitting and proportion accuracy.
30
September 3, 2023
Rudder was part of the fuselage, so I cut it off to better detail it further. After glueing its halfs together I realized the surfaces were a bit warped due to the pressure of the clamps, so I had to add some material on the outside. I added the hinges also.
31
September 3, 2023
Off topic: my favourite tools. The DIY sanding sticks are just a strip of sandpaper glued to a styrene bar with CA. Proved invaluable to obtain flat surfaces after puttying. I wish I had figured them out before!

Commenti

29 21 August 2023, 14:18

Robert Podkoński
Looks like it is going to be a fantastic model. Let me take a seat 🙂

21 August 2023, 15:03

David R. Meizoso
Welcome, Robert! It's progressing slowly. Panel lines are been filled/sanded/rescribed, wing surface levelled and smoothed, landing gear scratched, etc. Can't help digging my own grave with every project 😉 But yes, in my head it's going to be a fantastic model!

21 August 2023, 18:25

Spanjaard
Amazing details added, looking forward the rest

2 September 2023, 20:47

Michael Kohl
I folllow to

2 September 2023, 23:25

Pierre Pierre
Following, but serioulsy how did byou manage to make this riveting it is very straight on a such small scale ! Congrat

3 September 2023, 19:19

David R. Meizoso
Thanks, Pierre, and welcome! I first draw the lines on the surface with a mechanical pencil, then use Rosie the riveter freehand trying to follow those lines. For longer lines I use tape as a guide. The trick for me is to inmobilize the model while using the riveter, I use lots of blu-tac for this. Additionally having a source of light in front of you allows the rivets to be easily seen, which also helps a lot! Just find the right angle under which the surface reflects the light and there they are!

3 September 2023, 19:34

Björn Leichsenring
really fantastic work

5 September 2023, 06:52

Lochsa River
checking this out...great livery

5 September 2023, 07:32

Ronan
Very nice so far 👍

10 September 2023, 09:15

Shar Dipree
Wow great detailing. The C-415 will definitely look great when it's finished. 👍👍👍

10 September 2023, 09:26

David R. Meizoso
Thank you all! Scribing and riveting are slowly progressing, though I have less time for modelling now... I'll do my best not to loose momentum!

10 September 2023, 21:03

S M
Amazing work here! Following!

5 June, 20:19

David R. Meizoso
Thank you very much, S M! I had to stop modelling for a while due to a new job and the changes involved, but hopefully this and other projects will be resumed eventually.

6 June, 18:19

Mr D
Doing a great job, nice details, An interesting subject too 👍👍👍

2 August, 11:44

Zbynek Honzik
This looks like careful and precise build without compromise, David.
I'm taking a seat and looking forward to the next progression.

5 October, 15:43

Album info

This is an upgraded version of the Canadair CL 415MP of the Malaysian Maritime Enforcement Agency, as it was delivered in 2016 and before receiving its final white and red uniform.
Some new surveillance equipment was added and the aft doors were also modified on both sides, featuring this stunningly beautiful patchy scheme.

CL-415 MP Malaysian Maritime Enforcement Agency (MMEA)

31 immagini

1:144

In corso

Group Build

Sea Patrol Aircraft Flying Boats or Land Based will do! All nations and time?

1. Giugno 2023 fino a 31. Maggio 2024

Tutti gli album

Visualizza tutti gli album »