ニュースフィード
![](/profiles/img/user-s.jpg)
新しいフォトアルバムを追加しました。
41 28 March, 16:26
![](/profiles/img/user-s.jpg)
Build completed so far. Still waiting for the metal barrel. Quite challenging to attach the Zimmerit- PE parts. Was annoying when it comes to round shapes on the turret front armor. Treating those metal parts with some heat, made them much more handy to shape. First time using Friul tracks, very time consuming, but the best track result I´ve seen so far 🙂
1 April, 13:59
![](/profiles/img/user-s.jpg)
Lower part of the tank was painted and received weathering. Tracks were mounted and connected. Rear fenders were the installed. Next is masking lower section and painting the upper parts.
2 June, 10:18
![](/profiles/img/55070-763-s.jpg)
Nice job. I'm taking a seat.
Is it going to be some "Magdeburg-stuff" again?
2 June, 11:03
![](/profiles/img/user-s.jpg)
The tank received several rounds of paint. Starting with red brown primer, followed by dark yellow as base color and finally the camo pattern. Next is detail painting, and weathering.
9 June, 15:30
![](/profiles/img/user-s.jpg)
Initial weathering steps were conducted; chipping the Zimmerit and the metal surfaces.
16 June, 09:20
![](/profiles/img/user-s.jpg)
Thanks, Nick!
The exhaust was painted in a medium grey first. The parts having armor plates underneath were left in the original painting, as these area is less affected by heat and corrosion. Then a warm white followed by a reddish brown was applied using the sponge technique. Next was rust tones painted and blended with enamels. Colors of the original camo scheme where then applied with a sponge in the areas with less corrosion, to turn out the different stages of heat impact. Finally the upper parts received a slightly black shade to simulate the exhaust fume grime.
23 June, 08:21
![](/profiles/img/user-s.jpg)
Kick off for the base. Styrofoam is the desired material for house, road and pavement. As the road and pavement is covered with lots of dirt and debris, I added cobblestone only randomly. For the road thin sheets of styrofoam were shaped using a 3D printed rolling pin. In order to create more texture the stones were carved with a pencil. For the pavement an old brush was used to shape the small stones. Everything was painted in several greyish, brownish, sandy tones with acrylics.
The shape of house was cut with the Proxxon hot wire. To make the facade more interesting I added some "decoration" around the upper windows. A border seperates the upper and lower floor. Next is closing the gaps between the decoration elements at the upper windows and cover the lower floor with wood.
28 July, 07:18
![](/profiles/img/user-s.jpg)
Slowly taking shape. Lower floor fassade updated with some wooden panels. Dirt and debris was added to the road and pavement and painted with the airbrush. I used the same colors I used for weathering the tank tracks. Next is windows and door installation and of course detailing the interior.
18 August, 12:32
![](/profiles/img/user-s.jpg)
このアイテムを所有しています
![1:35 Canadian Armoured MG Carrier resin wheels (Copper State Models A35-008) A35-008](/products/img/0/4/0/1423040-19715-96-t180.png)
Canadian Armoured MG Carrier resin wheels
Copper State Models (CSM) 1:35
A35-008 18 August, 12:27
![](/profiles/img/user-s.jpg)
このアイテムを所有しています
![1:35 T-34/76 Model 1942 (Dragon 6479) 6479](/products/img/5/9/2/108592-140709-21-t180.jpg)
plant No.112 "Krasnoe Sormovo"
T-34/76 Model 1942 No.112 Factory "Krasnoe Sormovo" Late Production Dragon 1:35
6479 2008 新パーツ 18 August, 12:26
![](/profiles/img/137072-741-s.jpg)
新しいフォトアルバムを追加しました。
21 7 June, 15:25
![](/profiles/img/118183-835-s.jpg)
Cool! I was wondering how all the extra parts in mine looked when done, very nice. 👍
If you will accept a bit of advice, when you complete the cabin "shell" that goes into the fuselage halves, be prepared to do a lot of trimming and fitting before closing up. On mine, the sides of the fuselage wanted to push the roof of the cabin down and also hit the edges of the windscreen opening and that left a big gap on top. I finally got it acceptable fit, but even then, I wish I had cut more away because the cabin roof does not quite fit flush.
20 June, 15:34
![](/profiles/img/137072-741-s.jpg)
Thanks for the advice. I'll take care of it 🙂
I build a lot of Revell kits in the past and the fitting was different with every model. I have got everything between pretty good and horrible. It's always like a mysterious box.
20 June, 16:28
![](/profiles/img/118183-835-s.jpg)
I'm sure you will do well with all that Revell experience. 👍 The good news is that other than the cabin shell, the rest fits OK (ish) even the windscreens. But if you want doors closed, also be prepared to do some surgery on them.
20 June, 17:35
![](/profiles/img/user-s.jpg)
Looking good indeed! How did (or will) you paint the inside of the air intakes?
John is right with his comment, the cabine ceiling is a problem. I decided to keep the pilot door frames on the inside out for the moment. Without them the fitting seems to be quite good.
12 August, 20:01
![](/profiles/img/137072-741-s.jpg)
Thanks Andre! I already painted the air intakes with my airbrush. Now I will mask everything off so the paint is save for the yellow.
13 August, 07:31
/ja/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=ja
35
35
/ja/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo