Build Diary
![Album image #1 Album image #1](/albums/img/0/1/8/667018-46713-50-720.jpg)
My secondary work desk is topped with dry erase. So I use it to make notes or plan a build out. I knew I wanted to do a non-weathered candycoat for this build.
![Album image #2 Album image #2](/albums/img/0/1/9/667019-46713-13-720.jpg)
The Shin Musha has a lot of fiddly bits. This is just one leg, and just the exterior pieces.
![Album image #3 Album image #3](/albums/img/0/2/0/667020-46713-90-720.jpg)
Torso prepped for paint. I normally paint by batches of the same color, to reduce airbrush cleaning cycles. This time I took the opposite approach, and worked on each unit in series.
![Album image #4 Album image #4](/albums/img/0/2/2/667022-46713-52-720.jpg)
Seaming what was possible. There were A LOT of seams I couldn't seal/fill due to re-assembly. It's a weakness in my workflow I need to improve.
![Album image #5 Album image #5](/albums/img/0/2/1/667021-46713-14-720.jpg)
June was very wet and very humid in Philadelphia. I put a second moisture trap at the compressor, and a third one at the brush. Very necessary with a hose that long.
![Album image #6 Album image #6](/albums/img/0/2/3/667023-46713-44-720.jpg)
Between the shields and the gauntlet covers, these arms have a pretty restricted range of motion.
![Album image #7 Album image #7](/albums/img/0/2/4/667024-46713-57-720.jpg)
Head in the dryer. Instead of using the included green foil, i wanted to clearcoat the eyes in blue, hoping that they'd pass light better.
![Album image #8 Album image #8](/albums/img/0/2/5/667025-46713-31-720.jpg)
Pop Quiz: what's missing from this picture?
![Album image #9 Album image #9](/albums/img/0/2/6/667026-46713-32-720.jpg)
Yep, I lost the hose piece from the inside left knee. I was considering ordering a replacement runner, but decided to try to cast a copy from the other leg.
![Album image #10 Album image #10](/albums/img/0/2/7/667027-46713-89-720.jpg)
Mold on the right, positive was cast from milliput.
![Album image #11 Album image #11](/albums/img/0/2/8/667028-46713-24-720.jpg)
While the replacement was curing, I painted the rest of the leg. This shows the interim step where the primer and metalics are down prior to clearcoating.
![Album image #12 Album image #12](/albums/img/0/2/9/667029-46713-36-720.jpg)
This was the winner of 3 different experiments. The 3 colors listed on top are oil paints over a tan/yellow acrylic basecoat.
![Album image #13 Album image #13](/albums/img/0/3/0/667030-46713-17-720.jpg)
Closeup, and I was very happy with this once applied to the weapons. It is super delicate, so give it a couple days to dry, and apply topcoat liberally.
![Album image #14 Album image #14](/albums/img/0/3/2/667032-46713-90-720.jpg)
I toyed with a few ideas on how to make the katana hilt something special. I figured I would paint it, and cut some studs from styrene rod that I could paint to add some contrasting detail.
![Album image #15 Album image #15](/albums/img/0/3/1/667031-46713-14-720.jpg)
I rummaged around the local crafts store to find some tiny beads that I could paint with Testors Pearl. This was also a big fail. When airbrushed the paint didn't really stick to primed ball chain. Strike 2.
![Album image #16 Album image #16](/albums/img/0/3/3/667033-46713-64-720.jpg)
Oh, so maybe I shouldn't be thinking about attaching stuff to it. Lets bore the sockets out...
![Album image #17 Album image #17](/albums/img/0/3/4/667034-46713-56-720.jpg)
... and then fill them with liquid epoxy. I was thinking I could use the clear green like I did with the head gem, and it'd pass light when lit from behind.
![Album image #18 Album image #18](/albums/img/0/3/5/667035-46713-16-720.jpg)
It worked as designed, but now I have a really tough masking problem. I bored the same side hole into that scrap piece, forced through some funtack, and then put that over the epoxy fill.
![Album image #19 Album image #19](/albums/img/0/3/9/667039-46713-33-720.jpg)
Frisket mask to apply the kanji to the shoulders. One says 'SAMURAI' the other says 'SWORD' (katana)
![Album image #20 Album image #20](/albums/img/0/3/8/667038-46713-46-720.jpg)
![Album image #21 Album image #21](/albums/img/0/4/0/667040-46713-44-720.jpg)
Thats a photo of the board from the gameplay session. This is just a test piece.
![Album image #22 Album image #22](/albums/img/0/4/2/667042-46713-59-720.jpg)
And here is the final, printed in color, adhered to cardstock, and sealed with a UV protectant.
![Album image #23 Album image #23](/albums/img/0/4/1/667041-46713-64-720.jpg)
![Album image #24 Album image #24](/albums/img/0/4/3/667043-46713-78-720.jpg)
Also made a box for transport, and some custom pillows to keep him comfy. I intended this trophy to change hands as new people win games that challenge for the trophy.
コメント
27 October 2019, 21:42