News Feed
![](/profiles/img/user-s.jpg)
added a new photoalbum.
5 27 August, 06:51
![](/profiles/img/26469-299-s.jpg)
Well done...i do not even try to detail my models in such a way...really a very impressive model!!!
27 August, 08:13
![](/profiles/img/user-s.jpg)
It used a lot of materials here, such as ET model PE, glue sticks, glue plates, DEF wheels, 0.4mmrivets from mastermodel, and PE from other models,and here is also used tetramodel M142 kit.
28 August, 01:14
![](/profiles/img/123758-917-s.png)
owns this item
![1:48 F-5E cockpit & ejection seat conversion kit (Hobby Fan HF103) HF103](/companies/img/345-38473-15-p.jpg)
F-5E cockpit & ejection seat conversion kit
Hobby Fan 1:48
HF103 28 August, 01:02
![](/profiles/img/15656-162-s.jpg)
added a new photoalbum.
52 19 June 2023, 19:38
![](/profiles/img/15656-162-s.jpg)
This weekend both Essex and Hancock kits were started. You can compare these two on my garden table, Essex being a short hull version and Hancock one of the later long hull types. Therefore Hancock has the Ticonderoga Pontos set. I threw in a dozen of airplane sets and pillaged the Ion Model figures stock for about 420 seamen to take the stations. While making the requested change to the rear elevator (see shipmodels.info/mws_..pontos+essex#p919517 ) an error was discovered in PE part 605 and this can only be solved by completely scratching it. Also, I'll open up one rear elevator so I have to adapt the deck edge to that. The Hancock kit got some travel damage to the hangar deck, so that will have to be repaired too. But I think this is a good start to the project.
19 June 2023, 19:52
![](/profiles/img/15656-162-s.jpg)
The hangar doors present a compomise that I can't accept, showing some inside detail but with all gates closed down and an exaggerated thickness. I decided to remove all of them, beginning with the Hancock sprue. You can compare with the original Essex sprue. To replace the partially closed doors, I can choose between Evergreen grated plates (subtler paneling though one-faced) or the same metal foil as used earlier.
24 June 2023, 22:56
![](/profiles/img/15656-162-s.jpg)
The walls of the Hancock are now built. I found out that there are not enough Pontos PE doors of one design to replace all plastic ones, so Hancock and Essex will be getting a different type. A drawback to the hangar walls is the absence of locator holes. I made some pins myself. The plane cockpits were not in stock and will arrive later.
31 March, 01:55
![](/profiles/img/121979-911-s.jpg)
Read a lot about the Essex-class carriers, really interesting history and very interested to see how your ships turn out 🙂
31 March, 02:02
![](/profiles/img/15656-162-s.jpg)
Thanks, Rando. Today the second ship's hangar was closed off. In the Essex model I didn't need to remove a part of the hangar deck, so now there's a minute difference in the distance of the rear deck to the island structure. The fault should be in the Hancock bow section. I closed down some of Essex hangar doors, but I kept a peeping hole for the elevator shaft that I moved to the right like in Hancock.
2 April, 00:02
![](/profiles/img/45816-678-s.jpg)
This is some project Steven. These are not exactly small models (i have one myself - CV-13 USS Franklin)....and so much extra detail you are adding. Watching in admiration. Great work so far.
2 April, 06:18
![](/profiles/img/15656-162-s.jpg)
Thanks, Gary. The first PE parts are bent for the stern and the boat cranes of Hancock, after the hangar wall seams are removed with Tamiya filler. One part of the wall is badly fitting and needs to be shortened.
5 April, 01:27
![](/profiles/img/15656-162-s.jpg)
Lots of PE particles are now assembled to giant deck support structures. I accidentally used the Essex front deck instead of the Hancock one, so I had to remove the PE plate causing half of the ribs to jump of again and restore this to the Hancock deck. Now I'm about to begin the same again for Essex, that has a slighty larger hollow under the flight deck.
8 April, 01:40
![](/profiles/img/45816-678-s.jpg)
Nice progress Steven. Shame about the mix up but we all human, im sure at one point we have all used a wrong part or miss assembled.
Keep up the good work....and enjoy your build time.
8 April, 10:01
![](/profiles/img/15656-162-s.jpg)
Thanks for the acclaim, now Essex is also loaded with PE parts under the front deck. I also removed the rear lift floor in the hangar deck, because it will be visible through the side doors. The deck edges are getting PE plating with the correct catwalk acces doors and fire station hatches, but I'm still thinking about methods to remove the space behind these PE parts. Drilling is not enough.
12 April, 12:38
![](/profiles/img/15656-162-s.jpg)
Thanks Gary. The update today shows the reshaping of the Hancock bow. The angle of the kit bow is too shallow, so I cut out a wedge in the side and plied it back. The bottom part was split and clamped shut tighter, using sprue "rivets" to hold it closed. A lot of sanding followed, even after I had installed the port 40mm hubs on the hull. Another problem were the 18 doors that needed to be removed from the island structure, so I used my Proxxon for that. An extra is the comparison between 5inch/38 mounts from the kit, Flyhawk (yellow) and Pontos (Brown). Pontos is more detailed, Flyhawk has PE details and the kit is built up from different parts.
20 April, 10:19
![](/profiles/img/15656-162-s.jpg)
Thanks, Pietro. The islands now both have all watertight doors, and Hancock's island is already a bit further down the line sporting ladders, a PE walkway, the pri-fly cabin and a almost fully equipped smoke stack. For a movie about choosing the right watertight door in your model, see Youtube Video . I did find the correct type on some detail pictures in my books.
![](https://img.youtube.com/vi/DmaTJTPfXA4/maxresdefault.jpg)
23 April, 13:24
![](/profiles/img/15656-162-s.jpg)
A 45 picture update about Hancock's island. I made changes to the building plan where I saw the reference pictures didn't follow them. Loudspeakers were added. A cutout in the bridge deck was removed. The venturis on the different levels were added, but some don't extend far enough. Some of the PE hatches on the director towers needed to be scrounged from the ABSD project remains. All kinds of radar antennas are added, some I didn't find or identify yet, like the "stovepipe" antenna encircled on one reference picture. The SC-2 radar needed to be put on the platform for the side SK radar position. I did make the rear mast for the smokestack position, but removed it again because there is no trace of it in the reference. It might still be used on Essex.
26 April, 00:35
![](/profiles/img/15656-162-s.jpg)
Thanks Christian. Again a large update with changes to the Essex island. The front structure is made identical to Hancock and some scratched galleries are added. I decided to move Essex to the march 1945 scheme. Pontos has some parts for 1944 Hornet that are useful here, like the bridge walkway. Some areas like the stern will have to be adapted too. The same radar antennas are used, but some of them on different positions. I now added more airplane PE to the inventory, some of these should be finished to be able to close down the hangars.
2 May, 13:12
![](/profiles/img/15656-162-s.jpg)
The Avengers are now getting their PE cockpits, and the interior of the hangar is painted white.
6 May, 00:59
![](/profiles/img/15656-162-s.jpg)
Thanks, the airwing continues with the Helldivers, the Hellcats and the Corsairs, that had the hardest fit, so it's a good thing I had only six of them. I still have the same amount of planes not getting a cockpit.
8 May, 00:25
![](/profiles/img/15656-162-s.jpg)
Detailing of the port air outlet, the catwalk and starboard galleries of Essex. For Hancock it's only the outlets that were repeated. At first I was cutting small mesh parts, but it's better to cut them as a whole and add a PE crosshair. In the Trumpeter planes there is a tendency in the wing base to be cast offset (see color image) resulting in a skewed wing position when the fuselage halves are assembled. I'll often have to correct the angle. All plane fuselages have been fixed now and in the Helldivers and Avengers the seams are already filled and sanded.
11 May, 00:36
![](/profiles/img/15656-162-s.jpg)
The Helldivers are first to be completed with PE parts. The Pontos airbrakes are an improvement over the kit ones, and they can both be used for stretched wings or retracted ones. I drilled open the wheel wells. In the Hellcats, the cowling is incorrectly cast with one lower opening, so I shoved a node in each one and sanded it flat. A new opening is drilled and an oil cooler vent is then cut out under that. Takes quite a while.
14 May, 15:06
![](/profiles/img/15656-162-s.jpg)
The Hellcats are now all having a revised cowling and they also have a brass tube for the new prop position. The wheel wells are all drilled out and I made 10 scratch pairs because I only have 32 Pontos pairs for 42 Hellcats. For the Corsairs the wheel wells are rectangular which is a real pain to scrape out. The Avengers are still to be detailed, beginning with the tail wheels.
18 May, 00:52
![](/profiles/img/65234-189-s.jpg)
That are quite a lot of planes you're doing.Defintely will complete the build
18 May, 11:59
![](/profiles/img/15656-162-s.jpg)
I think so, Lode. Don't you fancy a carrier build yourself? You probably have a Yorktown 1/200. Today the painting of the airplanes was started. The wings are painted white but this I might have to redo in grey, they're too coarse. The planes are in grey now. I cut out the propellers and I needed extas for the Hellcats, so I changed the 6 optional 4-bladed Corsair props into 8 3-bladed ones.
21 May, 01:35
![](/profiles/img/21096-573-s.jpg)
ton of little airplanes will certainly make a great flight deck, picture 359 seems an MC Escher design 😉
21 May, 06:23
![](/profiles/img/15656-162-s.jpg)
Currently these planes are enveloped with gum to spray the camo on them. This is extremely tedious because the gum is not always adhering well and it must be sculpted exactly the same on each plane. I now painted the hangar floor in Lifecolor Deck Blue 20b (don't mind the overspray) and I also built the side elevators. This is a very nice fit from Pontos, but the netting supports are erroneously numbered 36 and this part is not abounding, nor does it fit the purpose. In stead of it should be used part 10, that was left in just the right numbers. The repair of the 5 inch/38 resin housings was first done with putty but then I wanted the outline to be improved and I made impressions with a knife flat and a drop of CA. Then break off the knife and a straight edge will result.
24 May, 15:21
![](/profiles/img/15656-162-s.jpg)
The 5 inch guns are now all detailed according to reference pictures of the ships. Essex was different than Hancock, it had no blastbags nor ladders. But in the end I noticed I used the wrong type of ladder, so maybe those will be removed. For the single guns one double gun barrel was wrongly shipped, so I lengthened that one with a 1mm Albion tube. Also some small parts are not provided in the needed quantity, or the option of placing PE steps was not shown in the manual.
27 May, 12:48
![](/profiles/img/15656-162-s.jpg)
The long range antenna pylons of Essex are according to the Pontos manual, but they copied this for Ticonderoga and that's incorrect. The 3d pylon should be left out for long hulls and so I can drop a 10th pylon for Hancock. One of the ladders for that can be used to complete the double 5 inch housings. Because of much unclarity in the manual I made many wrong folds on the catwalks and had to reassemble lots of parts with stress cracks. Also the deck edge elevator has a chain lift system that is now constructed out of a very fiddly frame that also breaks easily. But the end result is sturdy enough.
31 May, 00:43
![](/profiles/img/15656-162-s.jpg)
All planes are now in sea blue and ready for the last camo paint. The prop tips are painted in yellow. Some wings were stripped, others were overpainted in light grey.
5 June, 10:50
![](/profiles/img/15656-162-s.jpg)
Midnight Blue is almost completely added on all planes, only the Avengers still need the tail completed. Some of the wings had orange peel and were redone.
7 June, 01:02
![](/profiles/img/15656-162-s.jpg)
Thanks Gary! It went on with the elevator shafts, the Avenger tail colors, the propellers that were masked with a metal roundel (after 2 hours I now have painted about half of them black - on two sides!) and then finally the cockpit set arrived and I soon had some new Helldiver and Hellcat cockpits. I wanted the Dragon Avengers to have a PE cockpit too, but this was a very tight fit even afer milling as far as I could in the fuselage interior.
11 June, 23:59
![](/profiles/img/15656-162-s.jpg)
Thanks, David. Now it's decal time. 196 roundels on the wings, as many on the tails and again for the callsigns on the tailplanes. Essex has a horizontal white line that was trimmed with scissors and Hancock has a horseshoe. Still some more are coming, but for the numbers some research will be necessary. All decals were treated with Daco Sol. Plane interiors ar painted Vallejo Interior Green. Hellcat propellers are also painted.
14 June, 00:28
![](/profiles/img/15656-162-s.jpg)
Thanks for the comments! Today most of the canopies are cut up, ground thinner and applied to the fuselages. I'm left with the Hellcat open canopies, these just don't look the part and I will probably have to remove part of the tail to fit these.
1 July, 22:58
![](/profiles/img/15656-162-s.jpg)
I found a hack for making the perfect 1/350 Hellcat open canopy. Use 1/700 two-bar railing cut to four stanchions and bend this over the middle. By now I have placed all clearparts on the airwing. I now started t add the number decals on the Helldivers. You shouldn't follow the Pontos Hancock tailfin indications, these appear wrong as the number is always below the omega sign.
3 July, 20:01
![](/profiles/img/15656-162-s.jpg)
Thanks, Gorby. All crates now are sealed with Pledge and the props are installed. For the Helldivers I needed to scratch prop spinners out of clipped spheric node ends.
6 July, 00:49
![](/profiles/img/15656-162-s.jpg)
Tamiya grey panelliner wash is used on the top side of the airwing. I will be using a different shade for the bottom.
10 July, 00:36
![](/profiles/img/15656-162-s.jpg)
A brown wash was done on the grey undersides of the planes. The also got rigged, each of them with a scrap PE antenna mast. The Avengers got guns in the turret and now I will paint all the canopies on the outside.
12 July, 00:41
![](/profiles/img/15656-162-s.jpg)
All surfaces got a matt cote with Vallejo Polyurethane varnish, for the other side I avoided the gum because it removed some of the decals. Then all the wings could be fixed with a little drop of CA glue. There are no fitting locks for the stowed position of the wings, so all of them had to be manipulated in exactly the same position.
15 July, 00:38
![](/profiles/img/15656-162-s.jpg)
And more still to come. The update shows the closing down of the hull bottom with a waterline plate, that needs to be filled in with a lot of CA to get a smooth fit at the bow. The anchor deck is painted and the anchor chains are added (1 set was sufficient for both). The rear elevator shaft of Essex got a trompe-l'oeuil bottom part because the extreme right side is visible from the outside through the hangar hatches. The bow portholes are deformed because of the modling and are all replaced with Pontos portholes, of wich you get enough to complete the hull.
18 July, 00:22
![](/profiles/img/15656-162-s.jpg)
The decks are closed down after sanding the bottom. Some of the Pontos PE is interfering with itself, so that's clipped. I have some overview pictures for you, with the island and main guns in dry-fit. Now the catwalks can be added.
20 July, 00:25
![](/profiles/img/20442-422-s.jpg)
Remarkable work!
I still can't get over that you are building two 1/350 carriers at the same time. Madness I tell you. 😉
20 July, 04:50
![](/profiles/img/15656-162-s.jpg)
There is reason in it. For example the catwalk supports you see in this update, in stead of stopping at assembling 75 for one ship, you can do another batch for the second one, in stead of finding yourself a few years later in front of that task with the memory of those first 75 ones and having to do that all over again. I even found errors in one Pontos instruction that could be corrected with the other one.
Further in this update: fixing a sag in the deck caused by tensions in the connectors, just saw through the connectors after the deck is fixed to the hull. Also the ladder booms and a lot of Pontos steps that are either not present where expected to not fall off the ship, or that are mentioned in the manual but not used on the pictures. I also fixed the antennas to the catwalks.
25 July, 23:45
![](/profiles/img/15656-162-s.jpg)
There is enough material to build 25 quadruple 40mm Bofors, so I made them. Nevertheless you only need about 8 per ship. Now I'll start on the 130 single Oerlikon 20mm guns. Here the margin is much less, but the fit of the stands is bad so they have to be clipped a bit.
30 July, 20:54
![](/profiles/img/15656-162-s.jpg)
It seems that in 1944 Essex' gunshields were modified, so I had to remove a part from them. For the Hancock model this is not necessary. Every step in the 20mm guns is repeated 125 times, so that takes a toll.
1 August, 23:45
![](/profiles/img/20442-422-s.jpg)
Every time I see this I'm blown away by the effort you are devoting to it. You certainly have a lot more patience than I have.
2 August, 06:32
![](/profiles/img/15656-162-s.jpg)
With these little guns it's tested daily, Gorby. But now they are all done and painting can almost begin. The Hancock 20mm guns were finished when the handwheels were added, but the Essex guns are like on the reference pic and needed an Evergreen Mk.14 visor and a piece of scratch PE for the air feed pump.
4 August, 20:40
![](/profiles/img/15656-162-s.jpg)
In this update I scratched the fuel lines on the hulls, covered the deck ends with sheet metal, made the directors, added all Carley floats and placed the HF-antennas and some missing stuff on the islands.
7 August, 09:58
![](/profiles/img/15656-162-s.jpg)
The floater net baskets are made while the Deck Blue parts are masked on both ships. I tried out the excellent Eduard searchlight sets and used this on both, they outshine the Veryfire ones I used on Hancock first. Now back to the tedious masking of Hancock.
11 August, 00:57
![](/profiles/img/user-s.jpg)
I never thought I would say this......they're "bulkheads", not "walls". Forgive a former carrier mariner, but some of the lingo they jammed into my brain stuck. I also can't stand movies with officers wearing their lids indoors. : ) Your PE work is inspiring!
11 August, 02:00
![](/profiles/img/95177-962-s.jpg)
Impressive amount of photoetches and details, my head is spinning, admiration and respect!
11 August, 09:17
![](/profiles/img/15656-162-s.jpg)
If my work attracts the real carrier operators, I feel as humble as a pollywog. Thanks for the replies, today you can see the finishing of the masking phase and the Gunze primer coating. I used cardboard to close up the hangar hatches, I made it fit well enough to not need any glue. The next coat will be a complete cover of all parts with Lifecolor pale grey.
13 August, 22:47
![](/profiles/img/15656-162-s.jpg)
The hulls are at last painted black and can be unmasked. Some overspray was inevitable and can be removed with post-shade. The deck is first tainted with Gunze Midnight Blue and then faded with a light sand primer. Transverse girders are marked with an Aqualiner. To Hancock I added a paravane guide to the bow. The deck fit of Essex was perfect, now let's check out the other one. When the island is dry-fitted, it seems to have the right look from the pictures.
23 August, 00:43
![](/profiles/img/15656-162-s.jpg)
Thanks Gorby! Now both decks are applied, some setbacks needed to be resolved. In both ships the deck edge elevator was not fitting between the PE constructions to the outside of the hull. I should have corrected this before painting all. I did succeed in removing and reattaching the PE without all too much paint and PE damage, it might not be visible after the repair job. Hancock got the elevator level with the hangar deck and Essex got it stowed in vertical position. This is only possible with retracted safety netting, so that too was moved. I also made a schematic walkthrough showing how I needed to remove the front internal hangar bulkhead of the Hancock model, that seemed to have some badly fitting extra parts to the Essex original sprues. This didn't sit flush with the front elevator edge, so the wooden floor wouldn't fit below the well. It seemed impossible to resolve without opening up the front deck part, but there was another option. I sawed a large hole in the bottom plate and milled through a support plate and the extended hangar floor to be able to push the bulkhead out of the hangar. I then fixed it flush with the well and puttied the floor taht was left a bit mangled by the milling tool. A large part of this will be covered by the wooden floor.
24 August, 22:32
![](/profiles/img/15656-162-s.jpg)
The deck PE particles are pre-painted after being primered grey. Even with this primer they scratch easily. The wooden decks of Hancock and in larger measures Essex must be cut out where the PE parts come. Some of these aren't even pre-cut and must be traced form the parts, like the barriers. I know that laser lines must not overlap, so they wanted to avoid drawing the near-vertical lines over the planking. Because of that, it's better to do the barriers first and then the expansion joints. The gutters around the deck are added with Hancock and will now be completed on Essex.
28 August, 01:01
![](/profiles/img/user-s.jpg)
Good afternoon, I am interested in this model, so I wanted to ask you, do you ship to Serbia and how much is the postage? Best regards, Vladica Jović.
4 June, 15:43
![](/profiles/img/11761-776-s.jpg)
Vladica, I found the kit in my stash. I will package it tonight and calculate a postal estimate to Serbia for you. Kind regards, Dutch
8 July, 12:31
![](/profiles/img/user-s.jpg)
Let me know how much the postage would cost to Serbia, so I can see if I can afford it. Best regards, Vladica Jović.
8 July, 16:39
![](/profiles/img/11761-776-s.jpg)
Vladica,
I packaged the kit as lightly and securely as possible, but the shipping estimate to Serbia is $35.60. Your total would be $50 USD. If you want it, please send my your complete name, shipping address and email address for the Customs form. Kind regards, Dutch
8 July, 22:09
![](/profiles/img/user-s.jpg)
Thanks for the info. Sorry, but that's a bit much for me. Tell me how much it would cost to ship that model to Chicago? I have a relative there, so I could ask him to send to his address. Best regards, Vladica Jović.
8 July, 22:31
![](/profiles/img/user-s.jpg)
Okay, I'll contact my brother in Chicago today, to see if he's on vacation by chance and to agree on shipping. Please send me your Paypal account and your email address so that we can pay you and send you the address in Chicago. I will contact you as soon as I hear from my brother. Best regards, Vladica Jović.
9 July, 07:15
![](/profiles/img/11761-776-s.jpg)
Vladica, Can we possibly trade? I know of a vendor in Serbia who sells UpRise decals. Can you purchase UpRise1:72 Douglas A-4E/F Skyhawk Stencils - UR72176 in Serbia? You could just mail them in an envelope with a stamp to me. If I mail the Mirage to Chicago = 2 UR72176. If I mail the Mirage to Serbia = 3 UR72176. you think that is a fair trade, please let me know. Kind regards, Dutch
9 July, 12:06
![](/profiles/img/user-s.jpg)
In principle, it can. I'll stop by the Post Office afterwards to check how much the postage costs and I'll call the decal seller to ask if he has three in stock. I will contact you when I check it. Best regards, Vladica Jović.
9 July, 13:51
![](/profiles/img/user-s.jpg)
So I will buy you the 3 pcs of decals you asked for and send them to you, and you will send me Mirages to Serbia. I don't have to pay you anything. We will do so. Best regards.
9 July, 13:55
![](/profiles/img/11761-776-s.jpg)
Vladica, Please give my your full name, address and email (for customs form). Kind regards, Dutch
Paul Wiegman
2615 S. Hawthorne Circle
Tampa, FL 33629
USA
email: vertol-107@hotmail.com
9 July, 13:58
![](/profiles/img/user-s.jpg)
My adress Is :
Vladica Jović
XI Krajiške divizije 41/37
11090 Beograd
Srbija
Telephone: +38163342511
E-mail: jovac6421@gmail.com
9 July, 14:29
![](/profiles/img/user-s.jpg)
I just sent an inquiry to the dealer for the decals. I'm waiting for an answer. Best regards.
9 July, 14:30
![](/profiles/img/user-s.jpg)
I would just take a look at your decal offer tonight, maybe you have something I need, so I would pay you to send it all together, if I find something interesting.
9 July, 14:32
![](/profiles/img/user-s.jpg)
I just got a call from this man who sells decals. There is currently only one set in stock.
9 July, 15:03
![](/profiles/img/user-s.jpg)
He still doesn't know when he will get two more sets of those decals. What do you suggest ? Best regards.
9 July, 16:31
![](/profiles/img/11761-776-s.jpg)
Vladica,
I see the other two MIrage decals that you want. I can add those to the package. I can substitute the following UpRise decals:
(1) YF-23 Black Widow II, UpRise 1:144, UR144200;
(1) RA-5C Vigilante (RVAH-11) UpRise 1:144 UR14425;
(1) Boeing 707 KAL "First shooted" UpRise 1:144 URC14413
Or, if he carries CtA decals, then you could ask for:
(2) Boeing KC-135T Stratotanker Tail painted for a 100th anniversary 116th ARS, CtA Models (cut then add) 1:144 144073
Does that sound fair?
Kind regards,
Dutch
9 July, 17:46
![](/profiles/img/user-s.jpg)
So you want the following decals:
UpRise1:72 Douglas A-4E/F Skyhawk Stencils - UR72176
(1) YF-23 Black Widow II, UpRise 1:144, UR144200;
(1) RA-5C Vigilante (RVAH-11) UpRise 1:144 UR14425;
(1) Boeing 707 KAL "First shot" UpRise 1:144 URC14413
9 July, 18:08
![](/profiles/img/user-s.jpg)
Hello Friend ,
For me, you pack the following:
1. Mirage III Revell H-225
2, Israeli pre-1967 Aircraft & Helicopters
Mirage IIICJ, P-51D, Spitfire, Bell 205/206, S-58, Mosquito
Microscale | No. 72-105 | 1:72
3. Mirage - Part 02
Brazil, Venezuela & Egypt
FCM | No. 72-34 | 1:72
I would buy that, and I'll send you the decals. Is that possible? Best regards.
9 July, 18:13
![](/profiles/img/user-s.jpg)
Hello Friend ,
For me, you pack the following:
1. Mirage III Revell H-225
2, Israeli pre-1967 Aircraft & Helicopters
Mirage IIICJ, P-51D, Spitfire, Bell 205/206, S-58, Mosquito
Microscale | No. 72-105 | 1:72
3. Mirage - Part 02
Brazil, Venezuela & Egypt
FCM | No. 72-34 | 1:72
I would buy that, and I'll send you the decals. Is that possible? Best regards.
9 July, 18:50
![](/profiles/img/11761-776-s.jpg)
Hello Vladica,
I returned home early. I have located the two decals that you want and included them with the Mirage kit. I will mail the package tomorrow. You can send the UpRise and CtA decals when you get them all together. No hurry. Kind regards, Dutch
18 July, 21:43
![](/profiles/img/user-s.jpg)
Thank you very much. As soon as the seller informs me that the decals are ready for you, I will send them to you immediately. Best regards, Vladica Jović.
19 July, 06:27
![](/profiles/img/user-s.jpg)
Thank you for sending the package. As soon as they contact me that they have arrived, I will immediately go to Pančevo to pick them up and send them to you. Trust me, it's not up to me. I will contact you when I receive your shipment. Best regards, Vladica Jović.
19 July, 20:21
![](/profiles/img/user-s.jpg)
Good day, I just wanted to let you know that the decals I ordered for you will arrive at the end of next week at my friend's place because I'm going on vacation next week, so I won't be in Belgrade. My friend will pick up the decals and I'll send them to you as soon as I get back from vacation. Best regards, Vladica Jović.
1 August, 07:15
![](/profiles/img/user-s.jpg)
Good day Paul, just to let you know that I sent those decals for you today. The shipment number is: RR232353455RS. Let me know when it arrives. Greetings, Vladica Jović.
17 August, 12:29
![](/profiles/img/11761-776-s.jpg)
Vladica, I noticed that I have several items on your wish list. I need to reduce my stash and I propose to send you the items and will set a value much less than the price I have set on SCM, but perhaps including postage. In any case, a very good deal for you. Then you can send me more UpRise and CtA, & possibly CRM kits / decals later. Does this sound okay to you? Kind regards, Dutch
17 August, 17:57
![](/profiles/img/user-s.jpg)
When you make an offer for me, feel free to let me know. When you have prepared all that, feel free to send me an offer with prices, and we will agree on everything. I can always send you the decals you choose. Best regards, Vladica Jović.
21 August, 17:13
/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=en
35
35
/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo