Newsfeed
Dave Burgessheeft een nieuw project toegevoegd.
15 July 2018, 17:20
Dave BurgessThe CAF never flew the F-5E Tiger II. They were saddled with the older, almost useless CF-5A Freedom Fighter. However, I won this old Monogram 1:48 kit at a hobby show back in the early 1980's, and I didn't have much interest in any American versions of the Tiger II at the time, so I decided to to do it in CAF livery. Superficially, the two a/c resemble each other,and that was good enough for me! Call it a what-if project, if you like.
5 July, 01:25
Razor Rayis eigenaar van dit item
8 Dale Earnhardt, Jr. Dale Earnhardt Tribute Concert Monte Carlo
Revell 1:24
85-2844 2003 Nieuwe markeringen 5 July, 01:25
Al Richardsonis eigenaar van dit item
Bf 109G-5/6 Overtrees - Sprues only; no decals, instructions, mask or PE parts
Eduard 1:72
70157X 2023 Nieuwe onderdelen 5 July, 01:21
Jonathon Frywil dit item
Cruiser Tank Mk.VIII Challenger (A30) late production
Vespid Models 1:35
VS350006 2024* Nieuwe mallen 5 July, 01:14
Desert Marlinheeft een nieuw fotoalbum toegevoegd.
43 afbeeldingen
Israeli P-51D D-191 (2302)
1:32
I'm starting to Like It!
Project: P-51D Israeli D-191 (2302)
36 14 April, 21:47
Desert MarlinWell, the polycap that is supposed to link/sync the left and right elevators fell out during the process of joining the fuselage halves. So I had to saw out the little housing that was supposed to hold the polycap in place and set it manually. Looks like I have one "unforced error" so far...
26 April, 22:57
RandoThat Merlin is looking great. Looks like it came with the kit? Must be a lot easier than old resin, lol
27 April, 00:09
Desert MarlinIt's close to time to add the canopy and mask for paint. Lots of weathering yet to go. And the gun bays are looking a bit bland. Needs some additional paint and wiring.
1 May, 06:15
Desert MarlinTime to close up the cockpit and prep for paint. Going to be one of those traditional natural metal schemes with lots of wear and tear...
3 May, 05:06
RandoYep agreed Ky, my next P-51 will definitely be a Tamiya. How did detailing the gun bays go Marlin?
3 May, 14:37
Desert MarlinStill working on them. The fit has had only one issue that was even close to being worth mentioning. The right wing gun port on the leading edge did not fit perfectly. So I have had to do a little filling on the undersurface. The underwing scoop was almost an issue but seems to have settled into place. WARNING: one must fit the AILERONS BEFORE THE FLAPS. Otherwise the photo etched hinge does not get locked into place by the steel shaft from the outboard end of the flap. Missed this so it was unforced error #2...
3 May, 20:53
Desert MarlinOkay, after looking at some of the real aircraft, I am not sure there is any detail needed except to weather the bay and guns. I was expecting some electrical or other pipes/wiring, but alas, there does not appear to be any...
3 May, 21:41
Desert MarlinI'm back! So the masks provided are intended to be applied to the outside surface. However, it's really hard to mask the interior surface, so I cut the masks and applied them to the inside of the glass and then used Scotch tape for the outside. Leaving the interior a little "over masked, the black primer added to the outside with the flat black interior will create a nice effect overall.
2 June, 23:44
Desert MarlinBack at it! Prop is done, not yet weathered. Needs some scuffing along the leading edges.
1 July, 04:14
Desert MarlinI'm using Alclad and Metalizer. Sadly, my collection of Metalizer is shrinking. My choice for masking tape is 3M PostIt Notes. They work really well on the soft surface of Alclad Primers and Paints. Looking to seal it up next and start the process of marking/weathering.
4 July, 17:04
JohnI love the finish of Metalizer but hoo boy is it fragile. I hear you on supply. I'm all out of aluminum; stainless steel and jet exhaust are all that's left. 🙁
Your IDF Mustang is looking great, however!
4 July, 18:02
Daniel Olsonbegon dit item
MG Gundam-W Endless Waltz
XXXG-00W0 Wing Gundam Proto ZeroBandai Spirits 1:100
5063543 (2203514) 2022 Nieuwe doos 5 July, 01:07
Alister McDonaldheeft een nieuw fotoalbum toegevoegd.
20 afbeeldingen
USS New York - USS Photo Etch...
1:350
Turrets test fitted. Catapult rail on centre turret was entertaining to get into position. Instructions were very vague ...
Project: USS New York BB-34
12 25 March, 09:35
Steven Van DyckLooking great! Was the island structure a good fit? Because I will be replacing those poles.
29 June, 12:22
Alister McDonaldSteven Van Dyck. The island structure took quite a while to get sorted. The ends of the poles are shaped at angles which fit into the base of the island structure. If not fitted perfectly the island structure wont fit level. This one is about 2mm shorter than the original due to a few fit issues and getting it level.
5 July, 00:20
Steven Van DyckThanks Allister, I really should return to battleships with conning towers, it looks interesting.
5 July, 01:06
Dave Pluthheeft een nieuw fotoalbum toegevoegd.
6 3 June, 00:40
Clair GreenwoodWatching this one, how is the quality of the kit? I couldn't find any reviews but from here it looks pretty darn good.
4 July, 23:37
Dave PluthIt is excellent. It fits together very well and is well engineered. Well worth the money.
5 July, 01:03
ICM 1:35
/nl/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=nl
35
35
/nl/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo