He 280 V8
Details added to the cockpit walls
Custom wall datails
Wall details the etched panel will be seated on top of the frame at the left/front
Found a better piece for the panel in the scrap-box
Tanks for the cock-pit,
Oxygen and halon, will still add white stripes to the bottles. Plan to place them in front of the instrument panel, will hardly be visible but still a nice addition
Slowly getting there
Wings attached, had to cut of the guides on both wings to get a good enough fit. The same issue is there with the tail-part… Some putty needed on the engine seams and the fuselage-wing seam.
Small fix needed on the top of the fuselage
Nose looks good
Quick prime to reveal all imperfections
Some filling still needed
More to fill
Wing joints need a bit more work :/
Primed with Tamiya XF-63 German Gray, dark enough for marbeling and I like the color
Marbelling done with flat white (XF-1) and buff (XF-57). My first try ever 🙂
Cut out slots for the navigation lights, will do the lights of the transparent sprue.
Antenna added on top of fuselage, the plan is to drag the wires from both rudders
First 3 layers of Mr Hobby H-70 RLM02 Gray on, thinned 70% with Tamiya X-20A
First 3 layers of Mr Hobby H-70 RLM02 Gray on, thinned 70% with Tamiya X-20A
First 3 layers of Mr Hobby H-70 RLM02 Gray on, thinned 70% with Tamiya X-20A
Boarding ladder/stairs scratch-build.
Horisontal support added
Some more support and details added
Scale seems to be quite ok
Added a few steps to the ladder, would have been difficult to climb as it was 🙂
Painted with Tamiya XF-84 Dark Iron
5 thin layers done. I think this is enough, the marbeling is still visible but not too much.
5 thin layers done. I think this is enough, the marbeling is still visible but not too much.
5 thin layers done. I think this is enough, the marbeling is still visible but not too much.
Gloss varnish and decals applied. Note to myself, Eduard decals do not need Microsol! Ended up screwing one decal and had to go to V2 instead of V8 as planned for the decals.
Next up a light layer of gloss varnish on the decals before some light weathering.
Opmerkingen
22 21 November 2023, 17:53
Sam S
Thanks Christoph! Stillhave to figure out some graphics for the boxes on the walls, maybe cut up the dashboard decal that came with the set?
Thanks Christoph! Stillhave to figure out some graphics for the boxes on the walls, maybe cut up the dashboard decal that came with the set?
22 November 2023, 22:08
Sam S
Quite a lot of sanding to be done on the fuselage-wings joints… The starting point gave a gap of 1,5mm. The engines seem to fit snuggly to the wings, as the tail to the fuselage.
Will also have to rescribe the panel lines, out-of-the-box they are quite shallow. Also pondering about adding rivets to the panel seams 🤔
Quite a lot of sanding to be done on the fuselage-wings joints… The starting point gave a gap of 1,5mm. The engines seem to fit snuggly to the wings, as the tail to the fuselage.
Will also have to rescribe the panel lines, out-of-the-box they are quite shallow. Also pondering about adding rivets to the panel seams 🤔
24 November 2023, 06:33
Sam S
Ended up cutting of the guides on both wings to get a snug enough fit, still needs some putty for the seam to be perfect.
The same issue is actually present on the tail, most probably I'll cut of the guide also there to get a proper fit. The engines locked nicely into place, just need to tidy the seams and sand them good.
Ended up cutting of the guides on both wings to get a snug enough fit, still needs some putty for the seam to be perfect.
The same issue is actually present on the tail, most probably I'll cut of the guide also there to get a proper fit. The engines locked nicely into place, just need to tidy the seams and sand them good.
25 November 2023, 14:00
Sam S
Pre-primed with gray Vallejo surface primer to expose all imperfections, the situation was better then expected. Some work to be done on some joints, but nothing worse to tackle.
Some fixing to be done before dark priming and marbeling.
Pre-primed with gray Vallejo surface primer to expose all imperfections, the situation was better then expected. Some work to be done on some joints, but nothing worse to tackle.
Some fixing to be done before dark priming and marbeling.
25 November 2023, 19:24
Sam S
Painting completed with 5 layers, marbeling still visible lightly. About what I was hoping for. Quite satisfied for a first try on this approach
Painting completed with 5 layers, marbeling still visible lightly. About what I was hoping for. Quite satisfied for a first try on this approach
28 November 2023, 13:34
Robert Podkoński
Good job so far. I liked this kit very much despite the problem with wings fit...
Good job so far. I liked this kit very much despite the problem with wings fit...
1 December 2023, 20:23
Sam S
The wings were a pain in the butt to get in the right position. The decals are also a bit on the thin side for a guy who is used to Tamiya thick decals 😂
The wings were a pain in the butt to get in the right position. The decals are also a bit on the thin side for a guy who is used to Tamiya thick decals 😂
1 December 2023, 20:31
Sam S
Good idea for how to make the wing-lights (tip of the wing) are wellcome. Tested with pva-glue, didn't work. The result was not clear enough and stuck badly to the model.
Next tyr will be using parts of the clear sprue.
Good idea for how to make the wing-lights (tip of the wing) are wellcome. Tested with pva-glue, didn't work. The result was not clear enough and stuck badly to the model.
Next tyr will be using parts of the clear sprue.
2 December 2023, 13:48