Harrier gr7 1/144
1August 16, 2021First try at the cockpit
2August 16, 2021For size...
3August 16, 2021
4August 16, 2021Thinning the borders or replace with pe...
5August 16, 2021Scraped to make thinner
6August 16, 2021Before and after
7August 16, 2021
8August 16, 2021
9August 16, 2021Filled the seam between the wing parts
10August 21, 2021Cockpit installed
11August 24, 2021Opened up the airbrake
12August 24, 2021Took the contours by putting some paper over it an rub it with a pencil
13August 24, 2021What I want
14August 24, 2021To adjust a bit
15August 24, 2021Finished
16August 24, 2021Dryfit
17August 31, 2021Was trying to add the ribs, but sanded through the hull... so added a new backing with paper.
18August 31, 2021Had to make a hole to be able to push the backing down.
19August 31, 2021Adding some antennas
20August 31, 2021Adding some antennas
21September 3, 2021took a start on the landing gear...
22September 7, 20211 down, 1 to go...
23September 15, 2021And his brother... difference in fin position is 0.5mm... damn
24September 15, 2021Retrokit inlets... some difference
25September 15, 2021Glued some extra meat
26September 15, 2021And refueling probe
27September 15, 2021After some cutting
28September 15, 2021And extra meat sanded 😉 , refueling probe minus the tube installed
29September 24, 2021
30September 23, 2021Some dimensions of the LAU-5003 rocket launcher
31September 23, 2021Makeshift lathe
32September 23, 2021Makeshift lathe, paper is to prevent dents from the clamping mechanism
33September 23, 2021Lining could be better
34October 5, 2021Kit canopy
35October 5, 2021Wooden mold
36October 5, 2021Just heat a piece of plastic packing (now one of revells packaging of kit and paint) and it over the "mold"
37October 5, 2021Result
38October 20, 2021Canopy in two parts, but I tend to keep bending it despite the blutack in the last steps while adapting the rear of the main part...
39November 4, 2021Finally...
40December 20, 2021First color
41December 20, 2021Taping
42December 20, 2021More tape
43December 20, 2021Second color
44December 20, 2021Untaped, on to the next color
45December 20, 2021
46December 22, 2021Next color
47December 22, 2021Next color
48December 22, 2021Leading edges handpainted
49December 22, 2021Leading edges handpainted
50December 26, 2021Another maskingsession
51December 26, 2021Another masking session
52December 26, 2021And unwrapped
53December 26, 2021And unwrapped
54December 27, 2021Missiles taped in
55December 27, 2021And brushpainted
56December 27, 2021For size
57December 31, 2021On it's own feet for the first time...
58January 20, 2022Lost the decals for these... so tried with the AB
59January 20, 2022Lost and found... pull handle
60January 20, 2022Bang seat mounted
61January 20, 2022And installed
62January 20, 2022Decals...
63January 20, 2022And some more... not that much
64January 20, 2022Overview
65January 26, 2022Tried it with CA, but got foggy after filling the gaps...
66January 26, 2022
67January 26, 2022
68January 26, 2022Now with PVA glue
69January 26, 2022Some slight sanding to do, but... happy
70January 26, 2022Rearview mirrors installed
71January 27, 2022Done...
72January 27, 2022Done..
73February 8, 2022
74February 8, 2022
75February 8, 2022
76February 8, 2022
77February 8, 2022
78February 8, 2022
79February 8, 2022Finished
Opmerkingen
17 October 2024, 08:24 -
