Nyhetsstrøm
Ferry Lottermanønsker
Ground Equipment
Hunter or Harrier Crew Access LadderAircraft In Miniature Ltd 1:48
GE48110 2020 New tool Flertema (1!!)16 October, 19:31
Kars Janseier nå
Ford GT LM GTE 2017 Le Mans 24 hours/2018 Daytona 24 hours
Model Factory Hiro (MFH) 1:24
K-633 2017 New tool 16 October, 19:28
MiniArt 1:48John Acsjust joined this community.
4 October, 15:46
John AcsThank you. I didn't think I would be getting a message. I don't recall you being a member of the Exeter (UK) ISCA Model Makers Club - though I suppose scale-mates encompasses all sorts of disciplines from all over. Where are you writing from?
16 October, 19:26
Edmond Holcombefullførte
Douglas TBD-1 Devastator Monogram Classics (includes Limited Edition Collector's patch)
Monogram 1:48
85-7575 1999 Endret ??? 16 October, 19:24
David Hla til et nytt fotoalbum
8 bilder
This is not all it's cracked up to be …
1:48
Cracking across the tail decals. The gray smear is where I’d already started removing paint then though I really should ...
Prosjekt: Phantom FG1 “Colonial Navy “
5+ 3 15 October, 15:59
David HThis won't be in FAA colours as I don't have any more FAA decals for this era of phantom so it's going to have to RAF.
15 October, 18:42
Mr DHi Dave pain in the but when something like this happens to paint..?
It's all a learning curve.
I snapped a canopy in two recently.
Don't let it put you off, Velejo paints are very reliable and don't let you down.
I purchase a basic colours set when l first set out and never looked back.
Good luck with sorting it out..👍👍
15 October, 19:05
gorbyShame about the crazing as the model was looking very good. Do you know if it was the paint or the top coat which cracked?
15 October, 19:58
David HMr D , nothing puts me off, as you say it's all a learning curve. Gorby, I "think" it was too heavy a paint coat,. I've stopped using pure acrylics. I now use Tamiya acrylics thinned 50/50 or more with cellulose thinners (and a mask) gives a super smooth finish and no primer needed to key
16 October, 10:48
gorbyI've not heard of Tamiya acrylics being thinned with cellulose before. Normally I use the Tamiya thinners and find that works very well.
16 October, 11:02
David HIf you thin with cellulose (and leave it for a few hours) it breaks the particles down and gives a ridiculously smooth finish as well as etching into the plastic.
16 October, 12:40
Mr DHi Dave 👋
It's bit to Harsh for modeling Cellulose.
Isopropanol alcohol or Tamiya thinner is better and safer.
Cracking can happen if X2 paint coats are drying at quite different times.
16 October, 13:04
David HWhatever works for you…with pure acrylics I've had issues with " lifting" ymmv. Just don't try it with anything other than Tamiya. Tamiya is NOT a proper acrylic . "Proper" ie water based acrylics just turn to jelly 😉
BTW the FAA phantom was done with Tamiya acrylics thinned with Tamiya thinners.
16 October, 14:48
/no/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=no
35
35
/no/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo