Nyhetsstrøm

coporado
Build completed so far. Still waiting for the metal barrel. Quite challenging to attach the Zimmerit- PE parts. Was annoying when it comes to round shapes on the turret front armor. Treating those metal parts with some heat, made them much more handy to shape. First time using Friul tracks, very time consuming, but the best track result I´ve seen so far 🙂

Spanjaard
looks certainly good already🙂

coporado
Thanks bud!

coporado
Lower part of the tank was painted and received weathering. Tracks were mounted and connected. Rear fenders were the installed. Next is masking lower section and painting the upper parts.

Christoph Kunz
Nice job. I'm taking a seat.
Is it going to be some "Magdeburg-stuff" again?

coporado
Thanks, Christoph! This time its Normandy subject 🙂

Christoph Kunz
Next time I'll read the headline.
Stupid me...

coporado
The tank received several rounds of paint. Starting with red brown primer, followed by dark yellow as base color and finally the camo pattern. Next is detail painting, and weathering.

coporado
Initial weathering steps were conducted; chipping the Zimmerit and the metal surfaces.

coporado
Weathering of the exhaust section using acrylics and enamels.

Spanjaard
looks fantastic

Neuling
I agree. Very interesting dents and battle damage.

coporado
Thanks, Gentlemen! 🙂

Nick N
The exhaust looks awesome! How did you make that?

coporado
Thanks, Nick!
The exhaust was painted in a medium grey first. The parts having armor plates underneath were left in the original painting, as these area is less affected by heat and corrosion. Then a warm white followed by a reddish brown was applied using the sponge technique. Next was rust tones painted and blended with enamels. Colors of the original camo scheme where then applied with a sponge in the areas with less corrosion, to turn out the different stages of heat impact. Finally the upper parts received a slightly black shade to simulate the exhaust fume grime.

Nick N
Thanks a lot, this is very inspiring 🙂

coporado
Tank completed, time to start the dio 🙂

coporado
Kick off for the base. Styrofoam is the desired material for house, road and pavement. As the road and pavement is covered with lots of dirt and debris, I added cobblestone only randomly. For the road thin sheets of styrofoam were shaped using a 3D printed rolling pin. In order to create more texture the stones were carved with a pencil. For the pavement an old brush was used to shape the small stones. Everything was painted in several greyish, brownish, sandy tones with acrylics.

The shape of house was cut with the Proxxon hot wire. To make the facade more interesting I added some "decoration" around the upper windows. A border seperates the upper and lower floor. Next is closing the gaps between the decoration elements at the upper windows and cover the lower floor with wood.

Doubtingmango
Just found this. Stunning work with great narrative!

coporado
Thanks Doubtingmango!

coporado
Slowly taking shape. Lower floor fassade updated with some wooden panels. Dirt and debris was added to the road and pavement and painted with the airbrush. I used the same colors I used for weathering the tank tracks. Next is windows and door installation and of course detailing the interior.

Christoph Kunz
good work, in speciall the wood paint, tip top

coporado
Thank you Christoph! 🙂

Pietro De Angelis
Great work, congrats!

coporado
Thank you, Pietro! 🙂

coporado
Lower and upper floor and walls were detailed using Balsa wood and wallpaper. Added windows using Balsa and lasercut as well as some transparent plastic for the glas parts. Also the infantry miniatures arrived meanwhile.

coporado
Scratch built some interior from balsa wood and plastic residues. The attic floor was installed. Next is finally building the lower floor entrance and preparing the roof.

Rui S
I'm in 😎

coporado
Welcome aboard, Rui 🙂

coporado
More detailing on that house and a testfit with the first infantry guy.

Nicolas
I got this kit on the to do list as well so I'm following. Nice start.

Robert Podkoński
Following, of course! I loved these "original" Kovozavody kits.

Łukasz Gliński
What a trip down the memory lane for just 3 bucks 😄 👍

Ben M
The fit on this kit…. Not great, not terrible.

Guy Rump
Following. 👍

Ludvík Kružík
This really is a trip into history. I wish you well with your work on the model. And I'll be happy to follow the progress.

The drop tanks used on the Mig you are building are the original (older) version. They were attached directly to the wing (no hinge) and did not have stabilizing ailerons on the end. This type of tanks had one unpleasant feature. When dropping the empty tank, the tank rolled on the wing. This was annoying because it could damage the control surfaces. Therefore, these tanks were replaced by a new type with stabilizing surfaces at the end of the tank and these tanks were suspended on a wing hanger (tanks of this type are in the kit). This solution eliminated the rolling problem.

Ben M
Ludvik, thank you for the details. I did not know that. I imagine they usually did not drop the tanks on trainers.

I also masked the canopy last night. The molding of the frames are a bit vague and lots of curves so it will require some cleanup after painting.

Ludvík Kružík
Ben, you're right that trainer planes didn't usually drop tanks. In peacetime, in normal use, even combat aircraft don't drop tanks (except in emergency situations or exercises).

The purpose of my comment was merely to explain why the tanks on Indonesian aircraft differ from those in the kit.

I look forward to following your progress and wish you a lot of fun building the model and the result to your liking.

Mr D
Doing a nice job 👌
I would by one for 3$ anytime 🤣

Ben M
The fit on this kit is ludicrous. Having a lot of fun with it though.

Ben M
Well the other night I got frustrated with the Vallejo gloss black primer clogging my airbrush, so I added some Mr leveling thinner and gave it the worst orange peel ever as this is totally incompatible with the paint. I thought I could selectively strip the paint with windex but while that kind of stripped the paint it also dissolved a lot of the perfect plastic putty and also dissolved the canopy pva glue and masking. Also I broke off a wing and a horizontal stabilizer. So a bit of a setback.

I have constant problems getting the Vallejo gloss black primer to not clog my 0.4mm nozzle.

Robert Podkoński
Sorry to hear that, Ben...

Duster_d
It's sad, Ben. These Vallejo primers can only be diluted with distilled water because they are based on acrylic urethane (this is my IMHO). Even Vallejo's Thinner and Flow Improver for acrylic paints does not go well with these primers. The same applies to their polyurethane varnishes.

Martin Oostrom
Not saying this will solve your issue, but they have a video with ratios out: Youtube Video

Sy Bar
Wow that video seam to show it's a lot of hard work to get their primer coat working 👀
I'd go with mr surfacer 1500 approx 50:50 with mr levelling thinner, then if you need a gloss use mr Color gx110 again 50:50 with levelling thinner, sounds just as complex but I've never had this block airbrush and you can get rid of surface issue before you gloss saving the thicker gloss primer obscuring details..

Good luck on you build

Łukasz Gliński
Very sad nwes mate - hope to see you back on this project with the new kit, this one looks fubar unfortunately.

Ben M
I have not yet begun to fight. It is but a flesh wound.

Ben M
Painted some detail parts. Unlike the Vallejo primer, the metallics shoot like a dream. Started reassembly. I will have to re-putty and this kit needs a lot of putty. The canopy is a goopy fogged mess, I'm going to soak it in degreaser to hopefully strip off the future and start over on it.

Nicolas
What a mess. Good luck fixing it.

Finn
Following

Ludvík Kružík
The accident on your project is really unpleasant. I wish you a steady hand and a lot of patience in dealing with the aftermath.

Ben M
It's going okay. Not giving up is part of the fun for me.

M0rce
Wow, that looks like a tough kit...
Coming along nicely now though it seems.. 👍
Looking forward to updates.

Robert Podkoński
I'm impressed with your perseverance, Ben... Keep it up!

Ben M
I finally broke the pitot tube off, amazing it stayed on this long with all the handling I had to do. The second time I did the puttying I didn't sand things as smooth, live and learn. This kit has a lot of challenging fit issues. I think I will decal next. Fairly happy with the canopy, it was a bear to mask. The gun blast panel and air brakes came out nice, slight contrast with the rest of the nmf.

Ben M
Landing gear, drop tanks, and antennae on

Ludvík Kružík
Ben, I admire your patience and determination to finish the model.
Have you considered subtle colour differentiation of the individual panels? It'll brighten up the uniform silver surface of the aircraft nicely.

Ben M
There are a few panels painted a different color and some light weathering, but I'm keeping it subtle on this one as my photographic references don't show a lot of variation other than the gun blast panel and air brakes. I'll take some better pictures when it's done. I've done the full on panel painting before and I enjoy doing that!

Ben M
OMG. I took it outside to photograph it and I dropped it. Reassembly commences.

Alexander Grivonev
Beautiful paint & chrome, shiny!