Nyhetsstrøm
Juergen Klinglhuberla til et nytt fotoalbum
46 bilder
Junkers 86 K7 - Austrian markings '37
1:72
Prosjekt: Junkers 86 - Austrian markings '37
43 31 May, 15:38
Juergen KlinglhuberStarted this one.
The Ju 86 which were seen in 2 different Austrian markings, but at the end was never part of the Airforce. Here the overall silver Ju86 #311 at the airshow in Vienna-Aspern in early 1937.
2 June, 11:10
Juergen KlinglhuberThe mention aircraft was sent to the Airshow in Aspern as a "demonstrator" in austrian marking. Austria was interessed in buying 18 Ju86K-7. Due to several reasons Junkers was not prepared for that airshow and on short note removed the markings of an 86K-2 that was already prepared to be sold to Sweden. They put on austrian markings, a service number #311 and flew it over to Austria for just this one day. Flight captain Behrendt did a good job and the aerobatic air-display was a great success. So far so good. Why I am telling this? 86-K2 is a differend engine and cowling. The box is a 86E1/2. Aftermarket conversion products are out there (Kora) .....I had difficulties to locate/buy some.
Therefore: it is Scratchbuilding time again !!! 😎
5 June, 18:16
Juergen Klinglhuberthx Alec &Lukasz for you very kind support 👍 - appreciated.
But the first cuts are already done - no way back now 😉
(and I have to odmit: usually I like it to test my skills by a DIY task every now and then)
5 June, 18:51
Stefan FraundorferAh, a new and very interesting project. Of course I will follow that. Have fun with the Ju 86 Jürgen.
15 June, 07:23
Juergen KlinglhuberI have finished the modification on the engine resp. cowling. Some new pic's up-loaded.
23 June, 15:27
Roland SachsenhoferVery interesting and extremely promising! We talked about it in Ried, and now I'm delighted to see these ideas being realised in such an impressive way!
23 June, 15:30
TH SCALE MODELS (Thomas Haberl)Nice progress Jürgen! I´m in to see how this beauty comes together 👍
24 June, 14:07
Juergen KlinglhuberThank you mates for leaving your nice comments.Iam wWorking on the exhaust pipe currently. New picture up-date should be ready after this coming weekend.
3 July, 17:07
Juergen KlinglhuberAll mod's are completted now - after adding the windows of the cockpit I can move it to the paint hangar.
13 July, 20:27
Juergen KlinglhuberHey - thank you Roland for your feedback. That gives motivation of course 🙂
14 July, 16:01
Roland SachsenhoferThat's great, that's how it should be, because your construction progress here gives me inspiration 🙂
14 July, 17:20
Juergen KlinglhuberThank you Alec, Thomas & Cuajete. When I had finished I thought: "Grab, overdone. This bird was for sure not that worn as it went to the airshow more or less fresh from the manufacturer." But the more looked at it the more I was okay with the result. So your comments are welcome and soothe my concerns. 👍
9 August, 16:22
NicolasDon't worry Juergen, even on new airplanes there are sometimes clear visual differences in the sheet metal. For example, some manufacturers deburr the rivet holes with a grinding machine, the sheets are made of different alloys or are applied with different rolling directions, all of which have an influence on the appearance. I like it.
9 August, 19:16
Duster_dla til et nytt fotoalbum
2 bilder
Super Etendard (Academy\Modelist)
1:72
BF 6 glue is applied to the cockpit canopy (as a liquid mask), which means I have 2 weeks to finish the model. :)
Prosjekt: Super Etendard (Academy\Modelist)
4 17 August, 09:21
coporadola til et nytt fotoalbum
41 28 March, 16:26
coporadoBuild completed so far. Still waiting for the metal barrel. Quite challenging to attach the Zimmerit- PE parts. Was annoying when it comes to round shapes on the turret front armor. Treating those metal parts with some heat, made them much more handy to shape. First time using Friul tracks, very time consuming, but the best track result I´ve seen so far 🙂
1 April, 13:59
coporadoLower part of the tank was painted and received weathering. Tracks were mounted and connected. Rear fenders were the installed. Next is masking lower section and painting the upper parts.
2 June, 10:18
Christoph KunzNice job. I'm taking a seat.
Is it going to be some "Magdeburg-stuff" again?
2 June, 11:03
coporadoThe tank received several rounds of paint. Starting with red brown primer, followed by dark yellow as base color and finally the camo pattern. Next is detail painting, and weathering.
9 June, 15:30
coporadoInitial weathering steps were conducted; chipping the Zimmerit and the metal surfaces.
16 June, 09:20
coporadoThanks, Nick!
The exhaust was painted in a medium grey first. The parts having armor plates underneath were left in the original painting, as these area is less affected by heat and corrosion. Then a warm white followed by a reddish brown was applied using the sponge technique. Next was rust tones painted and blended with enamels. Colors of the original camo scheme where then applied with a sponge in the areas with less corrosion, to turn out the different stages of heat impact. Finally the upper parts received a slightly black shade to simulate the exhaust fume grime.
23 June, 08:21
coporadoKick off for the base. Styrofoam is the desired material for house, road and pavement. As the road and pavement is covered with lots of dirt and debris, I added cobblestone only randomly. For the road thin sheets of styrofoam were shaped using a 3D printed rolling pin. In order to create more texture the stones were carved with a pencil. For the pavement an old brush was used to shape the small stones. Everything was painted in several greyish, brownish, sandy tones with acrylics.
The shape of house was cut with the Proxxon hot wire. To make the facade more interesting I added some "decoration" around the upper windows. A border seperates the upper and lower floor. Next is closing the gaps between the decoration elements at the upper windows and cover the lower floor with wood.
28 July, 07:18
coporadoSlowly taking shape. Lower floor fassade updated with some wooden panels. Dirt and debris was added to the road and pavement and painted with the airbrush. I used the same colors I used for weathering the tank tracks. Next is windows and door installation and of course detailing the interior.
18 August, 12:32
S Ieier nå
McDonnell Douglas
F-15C Eagle Collectors' Hi-Grade Series (Limited Edition 3,000 pieces) Hasegawa 1:48
CH1 (CH001:3800) 1986 Nye deler 18 August, 14:05
ScaleFella NAFOønsker
M1/M1A1 Abrams T-156 Tracks M1 105mm, M1A1 Early, K1A1
T-Rex Studio 1:35
TR85048 2022 New tool Flertema (1!!)18 August, 14:03
ScaleFella NAFOønsker
M1/M1A1 Abrams T-156 Tracks M1 105mm, M1A1 Early, K1A1
T-Rex Studio 1:35
TR85048 2022 New tool Flertema (1!!)18 August, 14:03
ScaleFella NAFOønsker
M1A1 ABRAMS TANK Ukraine Update Version with Workable Tracks
Rye Field Model (RFM) 1:35
RM-5120 (RM5120) 2024* Nye deler 18 August, 14:03
ScaleFella NAFOeier nå
M1A1 ABRAMS TANK Ukraine Update Version with Workable Tracks
Rye Field Model (RFM) 1:35
RM-5120 (RM5120) 2024* Nye deler 18 August, 14:02
CasModelerla til et nytt fotoalbum
3 2 August, 04:14
Олег Оla til et nytt fotoalbum
41 2 March 2023, 09:24
CaptGPFYou have a very good knack for choosing interesting subject topics and making the kits fit them. The multi-pose effects are very striking.
27 July 2023, 14:24
Tim Carmanmarkerte denne som til salgs/byttbar
Aircraft Anatomy Of World War II Technical Drawings of Key Aircraft 1939-1945
Paul E. Eden, Soph Moeng
2007 18 August, 13:53
/no/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=no
35
35
/no/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo