Nyhetsstrøm

Dave Burgess
This an absolutely TERRIBLE kit! It looks like a Chinese (Mister Craft?) knock-off of the Tamiya kit, complete with diagrams that look like they've been copied from the Tamiya instructions. Unfortunately, they didn't copy the parts! The kit quality was horrible, very little detail, and what detail was there looked like it was scribed in with a chisel. Landing gear struts molded into the L.G. doors, a laughable ejection seat that looks NOTHING like the depiction in the instructions, and really crappy soft plastic with a really rough surface. Still, I got it for the livery (Starblazers) and decided to do it anyway. That is, until I started decaling and found the decals SO fragile, that they shattered as soon as I laid them down and tried to position them. The four wing panel decals each had several cracks running through them even before I started to cut them off the sheet. I'm going to try to find a better Starblazers decal sheet, but quite frankly, it's not worth wasting it on this kit. Mister Craft's F-84G has been consigned to the waste basket. I won't be purchasing any more kits from this Chinese P.o.S. manufacturer! I'll get another Tamiya kit instead!

Erik De Smet
Yes, indeed a terrible kit. The kit seems to be a copy of the very old FROG kit, and the molds are still used and re-issued by several POLISH brands , including Mistercraft, Big Model etc. with equally poor decals. The Tamiya kit is by far the best, but is sold out almost everywhere. The Academy/Italeri is also good but hard to find, The heller kit is obsolete too. Have a look at my album : Thunderjet comparative build : Thunderjet comparative build | Album by opadesmet (1:72)

Colin
I feel your pain. Out of the two Mister Craft kits that I have tried (a Harrier and a SU-20), both had horrible mismatch between the instructions and the parts that were actually included. The Harrier kit even had the wrong amount of pieces advertised on the box (over 30 pieces less than advertised). You really get what you pay for with this brand.

gorby
Nice work!

Ben M
Looks great so far.

Lost_Erik
Good stuff!

Doubtingmango
Nicely done!

DerMattes
Following.

Ekki
Watching too.

CaptGPF
Same! Want to see how this turns out!

Nicolas
Following too.

Patrick Hagelstein
Interesting! 👍

Łukasz Gliński
Joining the party 👍

Mid Franconian
➡️🍿🛋️‼️

Thomas Kolb
Very nice cockpit! How do you find the 3D decals, are they worth the extra cost?

Falk Röllig
Welcome mates. In 1:72 scale 3D decals are a way better than pe and my hands are to shaky to paint. I use them for most of the models with open canopies. For inflight models and with pilots i think it's not necessary. With Kelik and Eduard 3D i'm not always happy, but Quinta for me it's the first choice.

Gergő Takács
Nice! I take a seat. I have a same project right now.

Finn
Following

Martin
Good Start!

Ekki
Following

Finn
Me too

Guy Rump
Me as well. 👍

DerMattes
Following as well.

Glynn Jacobs
VERY nice work!

Cristian A
Excellent project, watching. The Argentine Étendard aircraft were effective in causing significant damage during the Falklands/Malvinas conflict.

Michael Kohl
Following

Duster_d
Modeling is enough for today. I'll continue tomorrow.

Martin
Looks very promising!

Gerald
Hello Welcome here 🙂

JimboHUN
thanking you kind Sir

Thomas Kolb
This looks like a fun project! I will definitely take a seat!

DerMattes
Welcome and thank you 🙂

Bernd Grün
Schöner Start! Bin dabei.

Michael Rotthowe
Since I have started the exact same kit, turning it into a Marineflieger 104 with Kormorans, I will most definitely be following 🙂

DerMattes
Danke Bernd 🙂
@Michael I only have the kit without the Marineflieger decals, hence the Peddinghaus ones. I 3d printed the Kormorans with the specific pylons for the F-104G. They were designed by cults3d.com/@Sufa312 after photos I have taken at the Wehrtechnische Studiensammlung in Koblenz. I think he did a great job and the files are free 🙂

Ekki
Taking a seat.

Guy Rump
Following. 👍

S M
Following!

DerMattes
Welcome guys and thank you for your interest 🙂
Started working on the ejection seat. Decided to add the PE to the seat from the kit and see how this will look. Alternatively I have a resin MB MK.GQ-7(A) from Aires, but this thing does not look very different from the kit's seat. And the straps, etc. are PE as well.

Christian Lehmann
👍

Martin
Good Start!

Desert Marlin
The REEDOAK 3D Printed Pilots are awesome!

Desert Marlin
This project will have both pilots on the intercom and watching the engine startup process. That is why the same type figure is used in both cockpits. They both monitor the engine to ensure that the EGT and RPM is increasing appropriately. Each has their hand on the control stick to be able to open their MIC as they confirm everything is normal at start. The plan is to have the aircraft loaded with a Nuke (Apache Cruise Missile?). Seems appropriate to me for the days we live in now...

Desert Marlin
Have to pause this one until I get the BIG ED kit #33216...

Treehugger
Maybe go for resin seats as well?
Seems like kit plastic never can compete with resin seats. 🙂

Though, I no longer crave for resin interior for the cockpit because of the work, but seats are ok.

Desert Marlin
I'll paint these up and see if I can tolerate them. If they are too bland, I have time to change my mind! Thanks for the idea!

Desert Marlin
Great video of the weapon that goes with this version of the Mirage 2000N

Youtube Video

Desert Marlin
Time to return to the 2000N... Let's Nuke something!

Desert Marlin
I got the ResKit Mirage 2000N Cockpit Set (Detailed Version).

Desert Marlin
As I have begun work on this kit, I am yet again struck by the lack of information in the variations and options provided in the kit. For example, the tail tip is not called out that applies to the 2000N version. While the nose of the 2000D is provided in the kit, it has to be modified to make it correct for the 2000N. Oh bother…

Desert Marlin
Selected "most appropriate" tail tip and mounted the correct nose to fuselage.

Desert Marlin
Okay, now I'm excited to get some paint on this cockpit!!! ResKit, you guys have done some great work with your 3D Resin Printing!

Desert Marlin
I'm back to it!

Treehugger
Oh, did you fiddle with the nose part to make it match the N version, or did you have to buy aftermarket nose for the N version? I have this kit in my stash, but haven't really looked any it yet.

Desert Marlin
I'm using the D nose but converting it to an N version. I'm also closing the "sucker doors" on the inlets to represent an engine that is not yet started... I'm assuming initial hydraulic power is applied from the APU and auxiliary hydraulic pumps have brought the gear door up. I'm going to close the speed breaks for pre-engine start configuration...

Eric Thornton
Looks like BAM has some corrected noses still need the N one. Maybe reach out to him. I could use the corrected nose for this kit also. The Reskit stuff looks amazing.

bam-models.com/produ..2000-corrected-nose/

Desert Marlin
Thanks for the heads up! The BAM nose looks fantastic! Sadly, the 2000N nose has a pitot tube and does not have the RDY antenna lines. It seems that much of the 2000N systems are somewhat earlier than the -5 systems. Everything I can find on the 2000N seems to be somewhat austere compared with the 2000-5. The ResKit cockpit is worth every penny!

Mr D
Like it 😀👍
Nice when the pilot looks like he's actually doing something and engaged with the craft.

Desert Marlin
Thanks. It's really sad to remove detail from the ejection seat, but that is the only way to get the pilot in place...

Ben M
The pilot looks amazing.

Desert Marlin
The pilot is from REEDOAK. They have several different figures in various poses so the realism can be developed based on the aircraft scenario. This model is being build to represent events just prior to engine start.

Desert Marlin
Remaining cockpit items:
1. Glass
2. Decals on seats
3. A little more weathering
4. Fix pilot's France Flag
5. Add WSO's Right shoulder patch
6. Check that I can get the canopy actuators in after everything is assembled...
7. Add HUD glass

Martin
Cool project! I have my Popcorn ready, so I'll follow closely!

Guy Rump
Following. 👍

Nicolas
Me two.

Michael Schubert
Thanks, a little more work done on the cockpit this evening.. need to fire up my 3d printer soon for the jet exhaust but so far happy with how things are going together

Jennifer Franklin
Following, I am jealous that you have a 3D printer (soon, I will be joining you).

Mark Broughton
Great work so far looking forward to the rest of the model. Jennifer, having a 3d printer is a lot of fun, and also you can get some great prices on them now.

Jennifer Franklin
Bambu Labs came out with the A1 in November, which is only 500 CDN. They did a total recall on them in the last few weeks, but they expect to have them back on the shelves by May. I am waiting impatiently.

Michael Schubert
Took me a little while to get back on this, cleaned out the 3d printer and printed out the jet exhaust replacement parts.. now to prime and continue assembly...

Edouard Carr
Following also!