Nyhetsstrøm
Print Scale 1:72
Moaskela til et nytt fotoalbum
7 bilder
Sepecat Jaguar GR1 'Desert Cat'
1:48
Excellent fit ?
Prosjekt: Sepecat Jaguar GR1 'Desert Cat'
14 July, 09:18
Thomas Espela til et nytt fotoalbum
20 2 September 2020, 19:44
TreehuggerLooks similar to the one seen in the movie 'The Finest hours' (2016).
imdb.com/title/tt2025690
20 May 2022, 06:04
Thomas EspeThanks for the likes, all!
@Treehugger - yes, the movie is based on a rescue in 1952 by CG36500 (en.wikipedia.org/wiki/SS_Pendleton#Loss). The kit is not of that actual boat, but the same type (en.wikipedia.org/wiki/Lifeboat_(rescue)#36'_(foot)).
@Thomas - oh yes, it worked very well debonding the CA, I used 3/4 of a bottle to get rid if it all.
20 May 2022, 12:49
Andy WW1There's something extra nice about old kit rescue, looks good I shall follow along. Liking that wave base a lot 👍
20 May 2022, 13:32
Thomas EspeThanks, Łukasz and Andy.
The waves are made from 2-3 layers of tissue paper and watered down PVA.
The base itself is XPS with balsa framing.
20 May 2022, 14:02
Thomas EspeUploaded some images of the finished project. Quite happy with. The pictures are not that great though, I'm no photographer, but they give an impression of what the end result is.
22 September 2023, 10:29
Heikki Lankinenla til et nytt fotoalbum
19 bilder
M1A1 SA in Ukraine workshop - WIP
1:35
"UKR" looks like It's been welded by summer trainee, but I'll go with it!
Prosjekt: M1A1 SA-UKR Abrams tank
2+ 14 13 May, 19:17
Desert Marlinla til et nytt fotoalbum
51 bilder
Israeli P-51D D-191 (2302) [COMPLETED]
1:32
A really pretty Scheme!
Prosjekt: P-51D Israeli D-191 (2302)
43 14 April, 21:47
Desert MarlinWell, the polycap that is supposed to link/sync the left and right elevators fell out during the process of joining the fuselage halves. So I had to saw out the little housing that was supposed to hold the polycap in place and set it manually. Looks like I have one "unforced error" so far...
26 April, 22:57
RandoThat Merlin is looking great. Looks like it came with the kit? Must be a lot easier than old resin, lol
27 April, 00:09
Desert MarlinIt's close to time to add the canopy and mask for paint. Lots of weathering yet to go. And the gun bays are looking a bit bland. Needs some additional paint and wiring.
1 May, 06:15
Desert MarlinTime to close up the cockpit and prep for paint. Going to be one of those traditional natural metal schemes with lots of wear and tear...
3 May, 05:06
RandoYep agreed Ky, my next P-51 will definitely be a Tamiya. How did detailing the gun bays go Marlin?
3 May, 14:37
Desert MarlinStill working on them. The fit has had only one issue that was even close to being worth mentioning. The right wing gun port on the leading edge did not fit perfectly. So I have had to do a little filling on the undersurface. The underwing scoop was almost an issue but seems to have settled into place. WARNING: one must fit the AILERONS BEFORE THE FLAPS. Otherwise the photo etched hinge does not get locked into place by the steel shaft from the outboard end of the flap. Missed this so it was unforced error #2...
3 May, 20:53
Desert MarlinOkay, after looking at some of the real aircraft, I am not sure there is any detail needed except to weather the bay and guns. I was expecting some electrical or other pipes/wiring, but alas, there does not appear to be any...
3 May, 21:41
Desert MarlinI'm back! So the masks provided are intended to be applied to the outside surface. However, it's really hard to mask the interior surface, so I cut the masks and applied them to the inside of the glass and then used Scotch tape for the outside. Leaving the interior a little "over masked, the black primer added to the outside with the flat black interior will create a nice effect overall.
2 June, 23:44
Desert MarlinBack at it! Prop is done, not yet weathered. Needs some scuffing along the leading edges.
1 July, 04:14
Desert MarlinI'm using Alclad and Metalizer. Sadly, my collection of Metalizer is shrinking. My choice for masking tape is 3M PostIt Notes. They work really well on the soft surface of Alclad Primers and Paints. Looking to seal it up next and start the process of marking/weathering.
4 July, 17:04
JohnI love the finish of Metalizer but hoo boy is it fragile. I hear you on supply. I'm all out of aluminum; stainless steel and jet exhaust are all that's left. 🙁
Your IDF Mustang is looking great, however!
4 July, 18:02
CaptGPFGoing to steal your post it notes trick for my next metallic project. Even i]with Xtreme Netal paints, I still have to wait a couple of days after I seal it with gloss - thanks Marlin!
5 July, 15:40
/no/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=no
35
35
/no/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo