The build

1
January 28, 2019
The mixed bag starts here : The cockpit is super pretty and detailed. But you need to add some sprue under the control sticks, otherwise they'll tickle the pilots' underknees...
2
January 28, 2019
3
January 28, 2019
Again in the bomb bay : really nice oob but... the rotary launcher is poorly designed, it's 2 component pieces ploting actively to not align properly
4
January 28, 2019
... and the socket is too shallow. No biggie, you just need to strengthen it with some metal wire.
5
January 28, 2019
6
January 28, 2019
In this case a simple paper clip 🙂
7
January 28, 2019
... held in place with putty to avoid wiggly lost pieces in the inside later when the fuselage is glued together.
8
January 28, 2019
This is how the instructions would have you glue in the cockpit. Dont! if you do you'll have to deal with a pretty nasty gap with the upper fuselage.
9
January 28, 2019
10
January 28, 2019
11
January 28, 2019
Dry fit. Not much will be seen anymore... BTW i had to sand quite many inside parts to get the 2 fuselage halves to align properly.
12
January 28, 2019
Same for the engines, very nice details that'll disappear in the bowels of the beast !
13
January 28, 2019
This is how i would recommend (and did) glue the cockpit and the intake trunks for best fit and maxium bond.
14
January 28, 2019
Next the wing. I found it best to 1. glue the upper wings to the upper fuselage then 2. glue the lower wings and only 3. glue the lower fuselage. Best possible fit imho.
15
January 28, 2019
The lower fuselage with weight hold in place with putty. The white card is meant to reinforce the trap doors to the engines, as i elected to shut them up.
16
January 28, 2019
What did i get my self into....
17
January 28, 2019
Primed Tamiya Sea Blue, Light Grey for the RAM panels.
18
January 28, 2019
Oh the brilliant masks by New Ware. Pretty usefull as the decal sheet oob is quite basic with no RAM stencils. Very easy application of the great many stickers!
19
January 28, 2019
Took only 45 min to mask the upper and lower side. Those masks are really worth investing into.
20
January 30, 2019
21
January 30, 2019
Marbling done
22
January 30, 2019
23
January 30, 2019
And main coat in very thin layers. The mix is TF-54 , TF-77 and TF-08 in ratio 4:1:1
24
January 30, 2019
25
July 9, 2019
This actually - sort of - worked.
26
July 9, 2019
27
July 9, 2019
28
July 9, 2019
29
July 9, 2019
Bad case of silvering...
30
July 9, 2019
... that i havent yet figured out how to overcome. Suggestions welcomed.
31
July 9, 2019
32
December 22, 2019
Half a year after, back with new decals. Had to sand the top surface down (though most the original paint job survived somehow).
33
December 22, 2019
So far worth the effort i d say. Some fading and a final matt coat should provide an adequate result 🙂
34
December 22, 2019
Next time i ll paint the walkways and mask them before the base coat. Those long, thin and fragile decals are no fun to apply 🙁 (tombe fair the Begemot decal sheet performed over all very well)
35
July 11, 2020
36
July 11, 2020
37
July 11, 2020
38
July 11, 2020
39
July 11, 2020
40
July 11, 2020
41
July 11, 2020
42
July 11, 2020
43
July 11, 2020
44
July 11, 2020
45
July 11, 2020
46
July 11, 2020

Kommentarer

3 28 January 2019, 21:59

Dave Flitton
Watching!!

29 January 2019, 14:02

Xander Jansen
following

30 January 2019, 06:52

Berger Steve
Bravo. C est vraiment top

9 July 2019, 16:46

Łukasz Gliński
Following too

10 July 2019, 12:06

Vince Venezuela
It took about half a year to muster the courage to come back to this model, and try to save it from its very bad case of silvering. After taking advice and ordering a fresh set of decals, and after several hours of sanding down without hurting the original paint job too much, followed by more hours of touch ups and yet more hours of new decaling, the intermediate result os not that bad! Next step three more coats of gloss, a mist of base coat to fade the white of the new decals, a matt finished and we ll call it done 🙂

22 December 2019, 23:30

Vince Venezuela
Thanks i ll give it a try!

23 December 2019, 11:34

Black Baron
Stalking

28 January 2020, 14:28

Łukasz Gliński
That's a very nice progress. How did you fix the silvering issues?

28 January 2020, 14:32

Sven Schönyan
Nice to see someone else dealing with this beast!

Greeat result so far. I like the mottling and the ram panles! I think I should get some of the ram panel masking, too.

28 January 2020, 14:53

Vince Venezuela
And finally done, after a third sanding and a third decal sheet... the first attempt to fix the silvering failed miserably, with results worse than the application. For this last try, i only took care of the worst decals (the walkways and id numbers on the central top section). And switched gloss varnish from Life color to Tamiya acrylic. Also cut out the middle transparent parts of the decals. Still not perfect but now acceptable (from a distance and without excessive lightning)😉 looks like a B-2 at least!

11 July 2020, 08:18

Sven Schönyan
Very nice you´ve done it! Loks great!

11 July 2020, 08:58

Album info

So far a mixed bag of a kit.
The fit is generally pretty decent and the pieces nicely and fairly detailled.
And on the plus side... it's a FR%ç*"KING AWESOME B-2
But there are plenty "meh" and "duh" moments so let's dig into it^^

B-2A Spirit

46 bilder

1:72

Påbegynt

1:72 B-2A Spirit RAM PANELS kabuki masks (New Ware NWAM0361)

Alle album

Se alle albumer »