Mitsubishi Ki-46 Shitei III Dinah Recon PlaneSe: Lysbildefremvisning Mosaikk Liste 1January 9, 2020started with the main landing gear, doesn't always have to be the cockpit... 2January 9, 2020can be bettered in a simple way I think, just scraped the seams... 3January 9, 2020Some scraping with the tip of a knife later... 4January 9, 2020same trick here 5January 9, 2020and this could also be made a bit better... 6February 14, 2020Resin Cockpit set.... missing and broken parts 7February 14, 2020parts fairly equal 8February 14, 2020but resin part has shrunk 9February 14, 2020Plastic part fit is ok. So time to make some hybrid cockpit parts 10February 14, 2020original cockpit section 11February 14, 2020started the rumble 12March 1, 2020ready for paint 13March 1, 2020ready for paint 14March 1, 2020ready for paint 15March 1, 2020ready for paint 16March 2, 2020prepared the flaps 17April 21, 2020Added the brake waire and some bands in tape 18April 21, 2020Lost the original part, so remade it, could be done better, but it is hardly visible in the end 19April 21, 2020ready for primer 20April 21, 2020and afterwards 21April 21, 2020rear cockpit in base colors 22April 21, 2020Front cockpit in basecolors, a lot of details to be added 23April 21, 2020Seats in basepaint 24April 21, 2020the knobs, a lot of these to go around... tried painting them first and thicken the knobs before placing them 25April 21, 202010 on this piece alone... Honey, what did you do all evening, well euh, I detailed a few mm's.. 26April 21, 2020all knobs in place and touched up ... 27April 21, 2020engines ready for mounting... after mounting, hardly anything will be seen 28April 21, 2020started rivetting the wings 29April 21, 2020 30April 21, 2020 31April 23, 2020interior received some chipping and a wash 32April 23, 2020Photographer station ready for mounting 33April 23, 2020cockpit too 34April 23, 2020and the IP-panel 35April 23, 2020dryfit 36April 23, 2020dryfit 37April 23, 2020dryfit 38April 23, 2020dryfit 39April 23, 2020dryfit 40April 28, 2020for rivetting, draw the lines on the hull and wings with a pencil 41April 28, 2020then follow the lines with a rivetting tool 42April 28, 2020removed the wingtip lights 43April 28, 2020dryfit of the main clear parts, looks like an aircraft now 44April 28, 2020little distortion 45April 28, 2020here too, surprise !!! 46April 28, 2020even within a half a mm... 47April 30, 2020replacement wingtip light, basic shape, drilled a small hole and painted it red for the light 48April 30, 2020glued in place and ready to sand 49April 30, 2020underway 50April 30, 2020and ready 51April 30, 2020canopy taped in. maybe correction needed on one sticker 52April 30, 2020hopefully a better view on the rivetting 53April 30, 2020last dials added 54April 30, 2020other glass parts added 55April 30, 2020PE-plates for flap-housing added Kommentarer9 January 2020, 12:20Bart Goesaertcockpit ready for paint...1 March 2020, 21:13Bart Goesaertflaps ready for mounting2 March 2020, 21:47Bart Goesaertbasepaint on the interior...21 April 2020, 06:32David DeavallLooking great so far21 April 2020, 07:54Bart GoesaertThx David22 April 2020, 06:39Daniel KlinkFolliwing 👍 Great start Bart23 April 2020, 21:05Bart GoesaertThx Daniel24 April 2020, 06:28Bart Goesaertlooking more and more lika an aircraft... glass panels are very thin and distorted.. any tips?28 April 2020, 06:48Project infoMitsubishi Ki-46 Shitei III Dinah Recon Plane55 bilder1:48Påbegynt1+Alle albumSe alle albumer »