Wiadomości

Finn
Following

Jennifer Franklin
me too

Dietmar Bogatzki
taking a seat

Landlubber Mike
Thanks guys! Hope I make it worth your while!

Nicolas
Following

Neil
Me too 👍

Landlubber Mike
Welcome aboard Nicolas and Neil! Thanks for your interest.

Lochsa River
have to sit in...this is in the stash...I was looking at it yesterday...

Lochsa River
A tip...others who built this kit had trouble around the cockpit....

Guy Rump
Following! 👍

Carlo
Nice, a flying boat. Hope this(or Sword) kit gets re-issued one day soon..

Alec K
Taking a seat.

Landlubber Mike
Thanks for following guys. Lochsa, you're right about the canopy. There are fit issues in general with this kit - most of which aren't too difficult to deal with - but the canopy is a bit of a mess. I'm not really looking forward to that part of the build.

Robert Podkoński
Taking a seat here too!

Landlubber Mike
Thanks for joining Robert!

Michael Kohl
Didn't know the subject, like the projekt, love to follow.

Landlubber Mike
Thanks Michael - glad to have you along!

Ben M
💺

Zbynek Honzik
Taking a seat!

Landlubber Mike
Thanks Ben and Zbynek, welcome aboard! Thanks for looking in!

Alec K
Nice detailing and progress 👍

Transall NG
A nice and strong landing gear !

Landlubber Mike
Thanks guys! Transall, it seems a lot stronger than the kit parts which were made from pretty thin plastic.

Pietro De Angelis
Beautiful work, congrats!

Landlubber Mike
Thank you Pietro! Still a long way to go. In the middle of priming the fuselage and having gap and other problems popping up. This is the build that never seems to end 🙁

gorby
Amazing work on the landing gear.

Landlubber Mike
Thanks Gorby! This was my first time trying to scratch build landing gear. Took me probably 20 hours 🙁 I ended up using Albion Alloys brass tubing for a lot of it, along with music wire, copper wire, plastic tubing, and other materials. I've bumped it a few times already and it is very stable so fingers crossed it makes it to the finish line!

Mr D
Nice 😀👍 a water-bird , nice work and like the extras

Landlubber Mike
Thanks Mr D! Really appreciate it!

Jennifer Franklin
I love all the scratch building, especially the landing gear; it is very nice! It's a great result.

Landlubber Mike
Thank you very much Jennifer!

Michael Kohl
Time to replace the teaser picture with one of your build. 🙂

Landlubber Mike
That might jinx me!

Michael Kohl
Oh yeah. You gotta be super-careful with that. This site is full of black magic. Pssst. Between us: I know for sure because it's the only explanation how some guys here achieve their otherworldly results.
Happy modelling - but watch your back 😉

Landlubber Mike
Yeah, I know what you mean. Some people here are ridiculously talented!

I ended up finishing the JRS-1 tonight. Finally pictures in my album. And Michael, I did replace the teaser picture with my final build - now that it's done and stored in my glass case, much less risk of jinxing myself!

gorby
WOW Stunning result Mike!
Looks like you might be one of those ridiculously talented people. 😉

Guy Rump
Excellent modelling. 👍

Lost_Erik
Fantastic collection.

gorby
They are all works of art. Beautiful models.

Doubtingmango
So I just finished this little Italian job. The decals came out with a lot of the edges showing, which then got a lot worse when I added some washes. I used Microset on the decals, and then sealed them with Tamiya semi-gloss before the washes, but it actually looks like the washes got under the decals. Any thoughts?

Bogicevic Vladimir
It looks like you haven't spray gloss coat before you applied decals. Or decals didn't set well. There are two solutions. One is lacquer thinner. Put the thinner with fine brush in dots over the place where you have silvering. Thinner should destroy the film. If it raises paint under, just leave it, it will settle back. Important thing here is that, once you applied thinner, you shouldn't touch decal for something like 20 minutes, at least. Second way is mix of sugar and water, half - half. You make a hole with a needle on the decal, than you put mix on the top. It should enter in the space between decal and paint and, when drayed, make a gloss film in between them which will act as a gloss under the decal. Wipe excess mix with wet cloath and you are done.

Mr James
How annoying. I've never heard of the sugar water trick from Bogicevic. I'll be interested if this works. If the thinner, sugar trick fails, what else can you do but use a scalpel to cut around them, since you've sealed it,

Mr James
Oh, nice paintjob by the way

Doubtingmango
Thanks mates! I believe Bogicevic is right. I think I did fail to gloss coat before the decals. I think I'll try the sugar water first

Bogicevic Vladimir
Ok. There are few small tings I should add then. Heat the water first, when hot it will disolve sugar beter and apply it while it's still warm, it will have more viscosity. Make small hole or slice with modeling knife, put few drops of mix on the top and let it dry. You will see emidiatly if it's penatrating. When dry, wipe carefully excess mix with moist cloth. Repeat where neaded. I know it sounds ridiculous, but it worked for me many times.

Doubtingmango
Thanks Bogicevic! I'll give it a shot. If it doesn't work I'll try the lacquer thinner technique. I love this site!

Mark Sherwood
Where the *uck's this been hiding. Very nice build Mr Mango and I hope the decal solution from Bogicevic work's out🤞

Doubtingmango
Thanks Mark! So I punched some holes in the decals and applied the warm sugar water, but unfortunately it did not seem to make a noticeable difference. I decided my best shot was to just grab the scalpel and remove the decals, which was very easy. Bogicevic said the solution would get under the decals! I have successfully applied new decals, and my little Italian job is now base-worthy. New pics to come.

Bogicevic Vladimir
Well, you find a solution, which is the most important thing. I can not know why something that worked for me many times does not work for you in this case. Maybe that what I think is silvering is residual glue from decal paper. Who knows... Anyway, good luck with your project.

Doubtingmango
Thanks Bogicevic! You were definitely part of the solution

John
All's well that ends well. 👍 Mango, your builds have me hankering to do some armor but I still have commitments to do a couple more a/c. When I do get a chance, part of me wants to start small with a Pz IV, but another part says go for broke and do a Maus!

gorby
Very nice work!

gorby
Very nice. Beautiful scheme.

Spanjaard
it is a beautiful job Martin!

Martin Oostrom
Thank you buddy!

gorby
Amazing result! Very impressive looking model.

Villiers de Vos
Fantastic work.

gorby
Very nice dio Mick.