Wiadomości

Skyhiker
Oh, this looks like fun!

Chris Parsons
Oh ya!
Built a couple of Broplan vac kits, a real challenge but great for the feeling of overcoming a challenge and creative accomplishment

Thomas Kolb
OMG, what a challenge! 🙂 Those panel lines look quite uneven, will you try to rescribe them or just take them for what they are? In any way, I am super curious how these sheets of plastic can be turned into a model, so I will watch with interest!

DuperScale
Welcome mates, the panellines are aweful but the material is so thin, i'm scarred that i cut right trough it when i try to rescribe them.

Łukasz Gliński
Another BroPlan fan, welcome to the club 😄

Nicolas
Following. Got my first vacu kit this weekend. I hope I can learn something here.

Robert Podkoński
Ambitious project! Watching.

Chris Parsons
Hi DuperScale, I built a couple of Broplan vac ATR kits, converting one 72 500 to a 42 300. A few pics of the work in my "albums" if you're interested in the kind of model you can achieve from a Broplan kit with a bit of work…sweat and tears, foul language, alcohol and time….

Cristian A
Following along.

Michael Kohl
Mee too.

J35J
Following with intrest! 👍🏻

Finn
This will be good

Ben M
👀

Treehugger
DuperScale, how about scribing into a layer of primer paint?
This way, scribing should be a lot easier afaik, scribing into the primer layer of paing, and not plastic.
This guy on youtube did this, on regular plastic models though.

Treehugger
As for the clear parts, I wonder if it could be done this way
1) Cut out a square/rectangle shape, removing the oval form from windows. The larger the hole the better, to create some extra space around the old window shape. Enough space to work with putty later on.
2) Glue in a flat thin strip of transparent styrene on inside of model.
3) Glue in a square/rectangle shape transparent styrene, outside the model, laminated with the existing strip of transparent styrene on inside, so double layered.

If keeping the new window parts larger than the old window shape it should be easier to use some putty after adding masking tape that have the shape of the old windows. The larger these new outer square/rectangle window shapes are, the easier it is to add putty to create a smooth surface, then hopefully the center part is clear enough, to mask off the final shape of the old window shape, before painting.

Afaik a common issue using Mikro Kristal Klear is that you can't sand the clear part afterwards, because the clear part is like rubber iirc. You can iirc easily remove this clear part though, just poke/pull it out. Unsure if there would be any residue left after removing the rubber like liquid clear stuff after it dries.

Treehugger
Another thing one could do with clear parts an idea:
1) Glue in a long strip of transparent styrene on inside of plane.
2) Add some kind of epoxy or something that can be sanded, without the epoxy damaging the underlying transparent styrene.
3) Idea is to use the liquid stuff to fill in the perfectly shaped holes for the windows, then sand the liquid stuff flush after it dries.

What won't work imo, is doing multiple rounds of adding liquids to create some goo that goes transparent. I think if you sand this stuff multiple times adding more liquid stuff, you get a flawed result I think. I tried something like that with gloss varnish, trying to build up a solid clear shape. Did not work as expected.

Treehugger
In this thread, and in photo #13, the guy apparently put tape outside, and poured clear resin on the inside to fill the window holes. Unsure if such resin will react and maybe eat up or warp any thin parts ala vacuum kits. I guess this can be tested with some scrap plastic if having some piece left over.

Boeing 737-530 Smart Wings 1:144 | Album by Zbynek (1:144)

Łukasz Gliński
The UV transparent resin is usually sandable (to some degree), maybe that might help?
Similarly to Treehugger I'd reinforce it with a transparent styrene from the inside of the fuselage anyway.
Or you might leave the windows open and fill them with Kristal Klear after painting - this is what I did on my Jetstream, Avanti & Yak-40. But if you want to seal it with gloss varnish, remember to keep very thin layers (guess how I learned it 🙂).
[img1]
Blue Jetstream (SP-KWN) | Album by Woody (1:72)
Avanti! | Album by Woody (1:72)

DuperScale
Hi, thanks for the input mates. I'm quite happy with the kristal clear on the small windows and i think i do it like Lukasz said. After everything is done i do the windows as the last step.

The windscreen window could work but i think i used little to much of the kristal clear.

Mr D
Good to see a vacform 😃👍

Cuajete
Well done so far 👍

David Taylor
Watching.

J35J
Great work so far with the vac👍🏻

Mr D
Like the cockpit..👍
Lots of work but doing a 👍 job... Be rewarding when done.

Cuajete
Great (hard) job so far. Go on!

Guy Rump
Following. 👍

Chris Parsons
Very nicely done and great progress!
Keep up the great work

Roland Sachsenhofer
These pictures are the start of a model project that I had long shied away from with respect: the kit parts promised a lot of fun and a highly interesting aircraft as a result, but also a lot of 'toil and trouble'. On the other hand: the adventure simply beckons.... 🙂
Here you can see the parts in almost raw condition, I only started to detail a little with round and flat wire. The tricky question was how to treat the sensitive and already somewhat battered transparent part of the unusual cockpit glazing. I decided to cut off the two side parts, mask the inside and outside of the windows and only attach the central clear part at the very end. I like the pictures with the over-designed radial engine: what a power-to-weight ratio for these racing machines!
The last two pictures show the current state of construction and detailing.... Well, we'll see...

Robert Podkoński
Taking a first row seat!

Roland Sachsenhofer
Feel very welcome of course! 🙂

Roland Sachsenhofer
There she is now - at least on her own two feet, even if the appearance with engine and mighty cowling - not to mention the upper wing - will change a lot. The construction steps up to this point were accompanied by a lot of sanding, but the accuracy of fit turned out to be surprisingly good.

Skyhiker
Ok now that's one interesting plane. Certainly not a Laird a**. What a huge engine!

Roland Sachsenhofer
You're right!
A friend asked if I was building a flying washing machine - in fact, the empty mount for the huge motor still reminds me of it. All the more so now that everything is white: it went well with all the white that Martin Mars is currently applying and forms a good basis for the following 'lemon yellow'.

Skyhiker
Looks a bit like a cement mixer to me, but I can see a washing machine in there.

Roland Sachsenhofer
Thank you Skyhiker, Cement mixer - I'm laughing my arse off, the Solution is obviously an inspiring sight: how apt!
It's probably time for the massive cowling with the mighty radial engine to go on the front end. One step towards this is the colour yellow, which will remain on the wings and tailplane. I would like to use Gunze's 'Emerald Green' for the fuselage colour.

Roland Sachsenhofer
From this morning with freshly applied decals: everything seems to shimmer and shine appropriately - but it turned out that the decals are absolute 'self-destructors'. The ones you can see here on the model fortunately went reasonably well, but the large markings on the wings and fuselage were beyond repair: just crumbs. Now I'm looking for someone who might be able to make me some painting masks on a PC. Luckily I scanned the decal sheet beforehand.

Skyhiker
Gosh that's lovely.

Lex Jassies
I always enjoy the surprise you reveal to us. Often with a type of aircraft that I had never seen before. Please keep it up! 👍

Robert Podkoński
The colours are just psychodelic... I love it!

Ben M
Beautiful paintwork!

I don't know if this helps but I've sent scans of decals to stsdecals before and they were able to make replacements for the ones that shattered.

Lex Jassies
By the way, I really like that "Skyways Inc." logo

Roland Sachsenhofer
Hi mates, I'm sure you can imagine how motivating your reactions are - thank you very much! I'll try that, Ben, thanks for that too!

Juergen Klinglhuber
Looking gorgeous !! let me know if you are succesful with stsdecals, I might have other contacts too.

Simon Nagorsnik
Aussie M1- follow this!!

Mirko Römer
Welcome Simon 👍 More specific modifications will follow.

Simon Nagorsnik
Oh yes, modifications are good and you have found a good source of inspiration there😁

David Taylor
Thought they had Leopards,I'm in.

Łukasz Gliński
Once you posted pic #1, we are all waiting for that fancy tent to be included 😛

Mirko Römer
If Hobby Boss will release the announced Leopard 2A6 CAN, I might consider buidling such an umbrella! But for god's sake this will take much longer than Hobby Boss claims! 🙂

To be honest, I have only one picture of the Ozzy umbrella...

Łukasz Gliński
toadmanstankpictures..abrams_australia.htm
So now, you have at least few more 😛
PS. there seems to be a special stand for it too: ozarmour.com.au/stor..-umbrella-stand.html

Tom B.
Interesting variant of the M1 you got there 👍 Following along!

Mirko Römer
Thanks mates! Very interesting pictures, who knows...👍😁

Simon Nagorsnik
Nice conversions!

Mirko Römer
Black base colour, some lighted AK Australian green. Needs even more lightening... The installation of the tracks was quite fiddly but finally it looks much better than the oob ones.

Mirko Römer
Decals arrived today, looking nice! Went back to black priming, didin't like the green yet and will start with black.

Finn
Looking good

Mirko Römer
Basic colouration and filter applied

Burkhard D
Great job on the camo!

Mirko Römer
Thanks Burkhard!

Mirko Römer
Besides the umbrella...done

Guy Rump
Great job and well deserved trophy! 👍

Thomas K.
Gratuliere! 👍