Wiadomości
Jeroenchciałby nabyć ten przedmiot
Versuchsflakwagen 8.8 cm Flak (41/37) auf Sonderfahrgestell Pz.Sfl. IVc tracks
Friulmodel 1:35
ATL-111 2016 Nowe formy Więcej niż jeden temat (2)18 October, 21:30
ModelSvit 1:72
penublychciałby nabyć ten przedmiot
SAS& LRDG COMBO KIT - Chevrolet WA & Jeep
Dogfight Workshop 1:48
48A20 2024 Nowe części Więcej niż jeden temat (2)18 October, 21:24
Xa Charoznaczył ten przedmiot jako wystawiony na sprzedaż
Merkava Mk.IV
Friulmodel 1:35
ATL-99 
18 October, 21:22
Augie 2025chciałby nabyć ten przedmiot
Well Known
K2/Y Ambulances (Limited Edition Special Boxing) Gecko Models 1:35
35GM0070 2022 Nowe formy 18 October, 21:22
Qwertzeldodał nowy album.
13 zdjęć/zdjęcia
Revell Rosenbauer GFLF Simba 8x8
1:24
Before and after
Projekt: Revell Rosenbauer GFLF Simba 8x8
7 7 October, 13:54
Martin OostromI have been drooling over this kit since it was new, so definitely following
7 October, 14:21
BozzerYeah, I agree with Martin. This has always been a kit, I wanted to get my hands on. I actually saw the built model, at Bolton IPMS in January. Those tyres are amazing and the vehicle itself, looked almost space-like.
13 October, 06:42
Petr Krepsdodał nowy album.
13 zdjęć/zdjęcia
ERA-3B "Whale" Skywarrior
1:48
I’ve started with front wheel bay, I have used some Eduard’s PEs and some wires.
Projekt: ERA-3B “Whale” Skywarrior
Scratchbuilt
6 8 October, 16:31
H Katododał nowy album.
3 18 October, 18:54
Landlubber MikeWow, nicely done! Do you mind me asking what paints/colors you used for the finish and roof? Looks great!
Also, how did you do the license plate? Looks very clean.
Thanks!
18 October, 20:33
H KatoThank you for your comment! The body is GSI Creos #8 Silver sprayed with #101 Smoke Gray. The roof is Gaianotes CB-25 Desert Orange 33825.
The license plate was made by cutting a piece of Tamiya plastic sheet to size and sticking the included decal on it.
18 October, 21:17
NLAWScametovisitdodał nowy album.
28 16 July, 13:41
NLAWScametovisitSorry about the slow rate of updates everyone. I hurt my back at the gym so I'm having to avoid being hunched over at the modeling bench this week.
19 July, 14:02
NLAWScametovisitOK! Back at it with the interior. This kit is definitely a jump in difficulty from the last one. PE is definitely difficult, and if you're doing this kit, make sure you frequently fit check the flight seats and how they'll mount to the bulkheads!
7 August, 15:57
NLAWScametovisitAAAAAND I hurt my back again pushing too hard at physical therapy. :/ more delays
22 August, 19:14
NLAWScametovisitthe detailing on this kit is really lovely, but the fitting of the parts is really bad. And advice on fixing the massive panel gaps in pic 43 to 47 is appreciated.
3 September, 22:27
MoritzIs the top portion already glued on? If not, try adding some bracing with some cut sprues to force the sides apart. Right about where the kink/end of the doghouse is.
Is the aft bulkhead of the crew cabin causing the problem? If that is glued to both sides, forcing the sides apart may not work.
5 September, 04:03
NLAWScametovisitVery good advice. Had to pry it apart but addint braces definitely helped!
5 September, 18:58
Anatolii SmyshliaievIf still relevant.
Pic 43-45. Before gluing the fuselage roof to the lower part, I glued 2 spacers from sprue scraps between the walls.
Pic 46 and 47.
I simply cut off the inner side of the hood wall, leaving the outer side untouched, achieving a tight fit along the outer surface. And I puttyed a little bit on the front of the hood.
24 September, 08:14
Augie 2025chciałby nabyć ten przedmiot
60‘~70’s Saigon Shuttle Motor-Tricycle Depot and a take break drive [2 kits In 1 box]
Gecko Models 1:35
35GM0113 2024 Nowe części 18 October, 21:16
/pl/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=pl
35
35
/pl/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo