Wiadomości
Maik Berlin
dodał nowy album.
dodał nowy album.
51 22 February, 16:16
Frank Spahr
dodał nowy album.
dodał nowy album.
8 zdjęć/zdjęcia
HMS Cleopatra completed1:350
The vessel is shown in a moderate sea state, but without a really dramatic effect. To me, it´s more pleasing and effecti...
Projekt: HMS Cleopatra
10 22 May 2021, 13:12
Treehugger
I am sure I looked at the wip photos some time earlier, but I am wondering: How do you shape the bigger wave frequencies, and how do you shape the smaller wave frequencies?
I am sure I looked at the wip photos some time earlier, but I am wondering: How do you shape the bigger wave frequencies, and how do you shape the smaller wave frequencies?
22 May 2021, 13:24
Frank Spahr
Thanks a lot to you all, much appreciated! I produce the wave patterns of my bases by heat application only. I use a gas burner (only with proper ventilation and very carefully!) to shape the troughs of the waves, after marking the approximate shape of the hull on the foam board. Having done the wave pattern, I only then cut the base to size and only then make the cutout for the hull.
Thanks a lot to you all, much appreciated! I produce the wave patterns of my bases by heat application only. I use a gas burner (only with proper ventilation and very carefully!) to shape the troughs of the waves, after marking the approximate shape of the hull on the foam board. Having done the wave pattern, I only then cut the base to size and only then make the cutout for the hull.
22 May 2021, 13:37
Frank Spahr
Danke Euch! Ja, Styrodur aus dem Baumarkt, so dünn wie es zu kriegen ist. Habe seit letztem Jahr ein Schneidegerät dafür, das hilft sehr.
Danke Euch! Ja, Styrodur aus dem Baumarkt, so dünn wie es zu kriegen ist. Habe seit letztem Jahr ein Schneidegerät dafür, das hilft sehr.
22 May 2021, 15:24
Frank Spahr
Making Waves 3 | Album by Frank Spahr (1:350-700)
Habe gerade Bilder vom Schneidegerät in das Album "Making waves pt. 3" eingefügt.
Making Waves 3 | Album by Frank Spahr (1:350-700)
Habe gerade Bilder vom Schneidegerät in das Album "Making waves pt. 3" eingefügt.
22 May 2021, 15:39
PM27
posiada ten przedmiot
posiada ten przedmiot
F-4E Phantom II [U.S. Air Force Fighter-Bomber]
Hasegawa 1:72
00332 (C2) 2008 Nowe pudełko (wznowienie) 12 September, 17:44
PM27
posiada ten przedmiot
posiada ten przedmiot
Atlantic, Wasp, Avenger, PC-7 MLD, KLu/Royal Netherlands AF
Dutch Decal 1:72
DD72100 2021 Nowe formy Więcej niż jeden temat (4)12 September, 17:43
UweR
ukończył ten element
ukończył ten element
Sd.Kfz.222
Leichter Panzerspähwagen (4x4) includes photo-etched parts & aluminium gun barrel Tamiya 1:35
35270 (35270•2500) 2003 Nowe części 12 September, 17:42
Frank Spahr
dodał nowy album.
dodał nowy album.
10 zdjęć/zdjęcia
Building the Revell Wind Class icebreaker - the completed model1:300
I closed the remaining gaps between the model and its base using heavy clear gloss acrylic medium. I then added the figu...
Projekt: WAGB Burton Island
45 11 December 2022, 12:16
Spanjaard
WOW, this is just magnificent! i love the look of the pieces of ice.
WOW, this is just magnificent! i love the look of the pieces of ice.
12 December 2022, 13:15
Frank Spahr
Thanks a lot! I made the penguins from styrene rod, sheet and a bit of dental casting wax.
Thanks a lot! I made the penguins from styrene rod, sheet and a bit of dental casting wax.
12 December 2022, 19:49
Frank Spahr
Thank you all! There are 2 WIP images in the third album on the building process.
Thank you all! There are 2 WIP images in the third album on the building process.
13 December 2022, 05:10
Lochsa River
building penguins is certainly holiday appropriate....add a santa!
building penguins is certainly holiday appropriate....add a santa!
13 December 2022, 15:01
Bernhard Schrock
Very cool idea and impressive work. I like the idea with the Pinguins!
Very cool idea and impressive work. I like the idea with the Pinguins!
13 December 2022, 20:44
Juskifo
Building the Revell wind class icebreaker part 3 - making the base | Album by Frank Spahr (1:300)
👍
Building the Revell wind class icebreaker part 3 - making the base | Album by Frank Spahr (1:300)
👍
14 December 2022, 05:38
Ralf Topeters
The ice looks terrific! So much authentic life on the dio in such a lifeless area of the planet. I was amazed and astound!!! 👍
The ice looks terrific! So much authentic life on the dio in such a lifeless area of the planet. I was amazed and astound!!! 👍
17 December 2022, 18:55
Frank Spahr
Thanks a lot, much appreciated! I guess I´ll bring all three icebreakers I built to the next show ...
Thanks a lot, much appreciated! I guess I´ll bring all three icebreakers I built to the next show ...
18 December 2022, 06:58
Sid de Koning
chciałby nabyć ten przedmiot
chciałby nabyć ten przedmiot
Eurofighter Wheel set
Wolf 3D Resin Parts 1:48
WOL480412 12 September, 17:42
Daniel Taft
chciałby nabyć ten przedmiot
chciałby nabyć ten przedmiot
Strategic Air Command B-1B Lancer (14 options) (Strategic camouflage scheme)
Caracal Models 1:144
CD144025 2022 Nowe formy 12 September, 17:41
Roland Sachsenhofer
dodał nowy album.
dodał nowy album.
24 zdjęć/zdjęcia
T-38A The White RocketNowy: 12 September, 17:34 1:48
Projekt: T-38A Talon 'The White Rocket'
11 1 September, 06:57
Roland Sachsenhofer
Besides Martin Mars, there are other projects going on - although 'side project' always sounds so disrespectful. In reality, these are models that really excite me, the kits are excellent, with a few goodies you can add a little more value, and the original machines are a dream anyway!
Just like here: I'll show you 'The White Rocket'! This T-38A Talon was used by the Mercury astronauts as a training device, another interesting story. The kit from Wolfpack is good, but a few etched parts from Eduard in the cockpit and above all the 3D print of the two jets at the rear increase the degree of realism even further.
Besides Martin Mars, there are other projects going on - although 'side project' always sounds so disrespectful. In reality, these are models that really excite me, the kits are excellent, with a few goodies you can add a little more value, and the original machines are a dream anyway!
Just like here: I'll show you 'The White Rocket'! This T-38A Talon was used by the Mercury astronauts as a training device, another interesting story. The kit from Wolfpack is good, but a few etched parts from Eduard in the cockpit and above all the 3D print of the two jets at the rear increase the degree of realism even further.
1 September, 07:05
Roland Sachsenhofer
These five pictures show the latest status: the surfaces, decals included, are finished, now the assembly of the various antennas, sensors, landing gear, airbrakes, pitot tube, canopy.... canopy can begin! So, at least the final is already in sight 🙂
These five pictures show the latest status: the surfaces, decals included, are finished, now the assembly of the various antennas, sensors, landing gear, airbrakes, pitot tube, canopy.... canopy can begin! So, at least the final is already in sight 🙂
8 September, 15:54
Roland Sachsenhofer
This build has now come to an end: a generally pleasing modelling experience, even if I was a little disappointed with this - for me - first Wolfpack kit: the fit of the parts was wonderful, the detailing was pleasing - for example in the cockpit area and the well-represented complex hinge mechanisms of the two cockpit canopies. But then: the undercarriage, airbrakes, the turbine outlets... it was all rather 'meagre'.... Accordingly, some improvements were needed here: a cockpit interior set from Eduard and an etched parts set that helped to detail the undercarriage and - very helpfully - the airbrakes. The fabulous nozzles from ResKit were also a really good investment! I love the decals and also the decal version from Wolfpack: in the look presented here, this T-38A 'The White Rocket' was flown by Deke Slayton and 'Wally' Shirra in the astronaut training of the Mercury programme - a fact that fascinated me.
This build has now come to an end: a generally pleasing modelling experience, even if I was a little disappointed with this - for me - first Wolfpack kit: the fit of the parts was wonderful, the detailing was pleasing - for example in the cockpit area and the well-represented complex hinge mechanisms of the two cockpit canopies. But then: the undercarriage, airbrakes, the turbine outlets... it was all rather 'meagre'.... Accordingly, some improvements were needed here: a cockpit interior set from Eduard and an etched parts set that helped to detail the undercarriage and - very helpfully - the airbrakes. The fabulous nozzles from ResKit were also a really good investment! I love the decals and also the decal version from Wolfpack: in the look presented here, this T-38A 'The White Rocket' was flown by Deke Slayton and 'Wally' Shirra in the astronaut training of the Mercury programme - a fact that fascinated me.
12 September, 17:40
Dan Bacon
dodał nowy album.
dodał nowy album.
14 2 November 2020, 23:36
Dan Bacon
Pz.Kpfw.38(t) Ausf. B Hobby Boss Kit - Panzerbefehlswagen 38(t) Command Tanks SdKfz 266 (Fu5 and Fu6 radio sets with two rod aerials or SdKfz 268 (Fu5 and FuG 7 FM radio transceiver). Built to the point of now I must select a specific type. Original wanted to finish it with large frame aerials (SdKfz 267) but can't turn the turret to allow one of engines hatches modeled open to see the details. So the two (SdKfz 266 or 268) both use aerial rods and don't prohibit turning the turret and leaving an engine view.
Pz.Kpfw.38(t) Ausf. B Hobby Boss Kit - Panzerbefehlswagen 38(t) Command Tanks SdKfz 266 (Fu5 and Fu6 radio sets with two rod aerials or SdKfz 268 (Fu5 and FuG 7 FM radio transceiver). Built to the point of now I must select a specific type. Original wanted to finish it with large frame aerials (SdKfz 267) but can't turn the turret to allow one of engines hatches modeled open to see the details. So the two (SdKfz 266 or 268) both use aerial rods and don't prohibit turning the turret and leaving an engine view.
22 November 2020, 22:27
Dan Bacon
Starting another tank to go along with a 1940 France time period - Panzer IV Ausf. D - older Tristar kit 35023, so once finished have some German tank figures to go with vehicles
Starting another tank to go along with a 1940 France time period - Panzer IV Ausf. D - older Tristar kit 35023, so once finished have some German tank figures to go with vehicles
19 January 2021, 00:49
Pietro De Angelis
I had the pleasure of admiring it just now, wonderful work, congratulations!
I had the pleasure of admiring it just now, wonderful work, congratulations!
12 September, 17:40
/pl/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=pl
35
35
/pl/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo