Wiadomości

Giorgos
Watching!

Martin Oostrom
I spent a couple of hours cleaning up some parts that I cut of the frame

Bozzer
These curbside chassis, really upset me. Just like the Volvo VN. If the manufacturer, went to the trouble, of making an engine, and separate frame parts, with other kits, then why would they cheap out, on kits like these? I love what you're doing with this though. Keep the pictures coming, buddy 👍

Martin Oostrom
I didn't put up pictures of all the cutting and sanding. A summary:
All parts are cut, sanded and glued where possible. Only a few drops of filler were needed.
The cab consists of 10 parts that need to be positioned just right. **** job, but I think I managed.
Next up: Primer.

Martin Oostrom
And primer is on after a monster session. 200ml primer + 50ml SLT = just enough.
Primer is zero paints grey. But a dirty grey.

bughunter
Watching!

Martin Oostrom
Tamiya Bright Red for the chassis and Zero stone grey as main colour for the interior

Martin Oostrom
The Zero stone grey was a bit depressing, so I mixed a batch 50/50 with white to lighten things up a bit.
Tamiya aluminium was airbrushed, and Tamiya black as well.
Done with airbrushing for now. Letting the paint cure before decalling.

Qwertzel
Looking great so far!

Bozzer
Bravo mate!
Are those bolt heads, part of the kit?

Martin Oostrom
Thanks lads. The bolt heads are kit parts. Just moulded on.

Bozzer
That's pretty good moulding. I thought they were PE mate.
I'll get some pictures up myself, tomorrow, of what I've been up to?
It's been a rollercoaster, that's for sure!

Goldman
Great progress with the DAF

I do hope Revell will re-release all of its classic and colorful kits like this one. It will looks amazing with all the decals.

Martin Oostrom
Started with the decals. They're a bit older and fragile. Should have read the instructions better. Would have made life a bit easier now.
I don't know what Revell were thinking, but some of the curves are too steep for these decals. It takes a lot of softener, a hairdryer and a boatload of patience to get them right. Even then they tore in places. And I've only done 5 pieces.

Bozzer
Sorry to hear about your bad experience mate.
However, it's definitely made a difference, and I know, that it looks bloody fantastic!
This is why I'm not a big fan of decals. It's the worst part of any build, for me. Hence why I push myself, with my airbrushing? But, I have to be in the correct mood, in the correct conditions.
The decals on my Turnpiker, were terrible. The amount of decals softener that I used, started to affect the clear coat. Next time, I'm going to airbrush everything, and then put them both together, so you guys can give me your honest verdict.
But to try and airbrush those beautiful decals, that you have there, would take me years!
Do you think, you would have been better trying to copy them on your own decal paper, and trying it that way?

bughunter
What I hate most about working with decals is the fact that there are no spare ones (at least for older, no more available kits).
So I wish you a huge amount of patience and luck! Take care, it will look great 👍

Martin Oostrom
The overall quality of the decals is well enough. Thin, almost no decal film on the edges. It's just that on the rear of the cab, the trenches are so deep. Luckily this is the only part that has this. The roof has some extending bits, but there are seperate decals for those.
My life would have been a bit easier if I'd read the instructions more carefully. Revell wants you to decal some pieces, before glueing. That way all edges are nicely covered. I'm an advanced modeler, so I just did my thing...

The artwork on this one is a bit too complicated to airbrush, it would take me more than a few years.
It might take some time, but I'll finish this job in the end 😄