Build Log
![Album image #1 Album image #1](/albums/img/0/1/8/572018-46713-38-720.jpg)
Assembly, pretty typical
![Album image #2 Album image #2](/albums/img/0/1/6/572016-46713-91-720.jpg)
Upgraded to actuated hands
![Album image #3 Album image #3](/albums/img/0/2/8/572028-46713-25-720.jpg)
M16A2 printed from Shapeways
![Album image #4 Album image #4](/albums/img/0/9/7/572097-46713-65-720.jpg)
Aftermarket rocket pod, terrible kit.
![Album image #5 Album image #5](/albums/img/0/8/6/572086-46713-30-720.jpg)
So many cones.
![Album image #6 Album image #6](/albums/img/0/9/3/572093-46713-84-720.jpg)
Need something to mount, since it was meant for under a wing
![Album image #7 Album image #7](/albums/img/0/9/5/572095-46713-27-720.jpg)
Kitbashed together
![Album image #8 Album image #8](/albums/img/5/7/5/574575-46713-22-720.jpg)
Reference photo for a CH53 helicopter flare dispenser
![Album image #9 Album image #9](/albums/img/0/9/1/572091-46713-51-720.jpg)
Scratchbuilding a flare/chaff dispenser
![Album image #10 Album image #10](/albums/img/0/9/4/572094-46713-73-720.jpg)
![Album image #11 Album image #11](/albums/img/0/9/8/572098-46713-81-720.jpg)
![Album image #12 Album image #12](/albums/img/0/9/9/572099-46713-31-720.jpg)
![Album image #13 Album image #13](/albums/img/0/8/8/572088-46713-38-720.jpg)
![Album image #14 Album image #14](/albums/img/0/9/0/572090-46713-19-720.jpg)
Primed, everything is getting a rust primer. Re-used some rocket noses from the pod kit
![Album image #15 Album image #15](/albums/img/0/8/9/572089-46713-78-720.jpg)
Undocumented prior to this is a gunmetal put down lightly over the primer, then vallejo chipping medium over that. The lightness of the gunmetal allows the rust primer to peek through from certain angles, it is more impressive in motion.
![Album image #16 Album image #16](/albums/img/0/9/2/572092-46713-31-720.jpg)
Custom accessories got primed
![Album image #17 Album image #17](/albums/img/0/9/6/572096-46713-52-720.jpg)
Used 3 colors on top of the base coat. The brown used a larger stencil size and went down first, subsequent ones were smaller. Both sizes from Fallout Hobbies, great vinyl stencils.
![Album image #18 Album image #18](/albums/img/0/8/5/572085-46713-38-720.jpg)
Upper torso, mid camo
![Album image #19 Album image #19](/albums/img/5/5/6/574556-46713-95-720.jpg)
1:6 action figure accessories. The slide actuates, and the magazine is removable. I ended up not using these cuz the scale was just a tad off, and the model was getting too cluttered.
![Album image #20 Album image #20](/albums/img/5/5/7/574557-46713-87-720.jpg)
1:6 scale Ka-Bar, sheath clasp is magnetic
![Album image #21 Album image #21](/albums/img/5/5/8/574558-46713-80-720.jpg)
The chipping of the camo areas was harder than the base coat, likely due to much thicker paint. I struggled a lot with paint curling when trying to chip larger flat sections. Tapping with a toothbrush gave best results.
![Album image #22 Album image #22](/albums/img/5/5/9/574559-46713-11-720.jpg)
More examples of curling
![Album image #23 Album image #23](/albums/img/5/6/0/574560-46713-30-720.jpg)
Likely the worst of it, I'm glad this supposed to be a heavily weathered build.
![Album image #24 Album image #24](/albums/img/5/6/1/574561-46713-38-720.jpg)
Army Star stencil cut from frisket
![Album image #25 Album image #25](/albums/img/5/6/2/574562-46713-84-720.jpg)
Before my first attempt at an oil pin filter for rust and fading
![Album image #26 Album image #26](/albums/img/5/6/3/574563-46713-60-720.jpg)
Oil Pin Filter in progress
![Album image #27 Album image #27](/albums/img/5/6/4/574564-46713-69-720.jpg)
This photo is terrible, but the right arm is weathered, the left one is not.
![Album image #28 Album image #28](/albums/img/5/6/5/574565-46713-35-720.jpg)
I think i'm going to use weathering master on the raw steel of the inner frame
![Album image #29 Album image #29](/albums/img/5/6/6/574566-46713-79-720.jpg)
![Album image #30 Album image #30](/albums/img/5/6/7/574567-46713-30-720.jpg)
![Album image #31 Album image #31](/albums/img/5/6/8/574568-46713-81-720.jpg)
I think the edges of the chipped areas may have gotten worse during the turpenoid application. I wonder if the satin varnish coat i put down after chipping was insufficient to protect it.
![Album image #32 Album image #32](/albums/img/7/7/6/600776-46713-89-720.jpg)
I wanted to build a more sophisticated base.
![Album image #33 Album image #33](/albums/img/7/7/7/600777-46713-43-720.jpg)
Initial attempt at rice paddy terrain, but...
![Album image #34 Album image #34](/albums/img/7/7/8/600778-46713-17-720.jpg)
I didn't like that color scheme, so I reversed it
![Album image #35 Album image #35](/albums/img/7/7/9/600779-46713-65-720.jpg)
Each plant is mascara brush bristles in hot glue, painted.
Komentarzy
4 February 2019, 12:45