Bf 109F-4/Trop Rote 2

1
February 17, 2019
Project inventory
2
February 21, 2019
Sidewall detail comparison
3
February 21, 2019
Succesful dry fit
4
February 21, 2019
5
February 21, 2019
Rudder pedals installed
6
February 21, 2019
Comparison Aires vs. Hasegawa's IP
7
February 27, 2019
Headrest with PE attachments and holes drilled in IP
8
February 27, 2019
PE added
9
February 27, 2019
Missing trim chain added from twisted copper wire - ready for primer!
10
February 27, 2019
No idea what that's for??
11
February 28, 2019
Black base
12
February 28, 2019
Fuel inspection added from stretched clear sprue
13
February 28, 2019
RLM66 base
14
February 28, 2019
blend coat and highlights added
15
February 28, 2019
A little bit too bright right now, but clear coats and the rather small fuselage opening will tone it down
16
February 28, 2019
Dry fit on the IP, acetate backed with white colour
17
March 4, 2019
Details painted, some touch ups needed on the fuel line
18
March 4, 2019
19
March 4, 2019
20
March 4, 2019
Green fabric belts vs. PE belts - what to choose?
21
March 4, 2019
Chain drilling the fuel port
22
March 4, 2019
After lots of scraping and sand ing: fuel port installed
23
March 4, 2019
Minor modification on the Aires cockpit rear wall
24
March 5, 2019
Chipping on the seat, floor and trim wheels
25
March 5, 2019
Comparison Hasegawa vs. CMK
26
March 5, 2019
27
March 5, 2019
Brake line from Hasegawa, looks toyish to me -> will be replaced
28
March 5, 2019
Some panel lines and panels filled on the wings
29
March 5, 2019
There's a piec of plastic for the bulged wheel well ceiling. Fit is horrible, but luckily invisible on the finished plane
30
March 7, 2019
Aires seatbelts assembled, not as fiddly as expected
31
March 7, 2019
Everything in place, dust pigments on the floor and seat
32
March 7, 2019
Middle brown wash on the seatbelts
33
March 7, 2019
IP finished
34
March 7, 2019
Fuselage buttoned up and cockpit put into place
35
March 7, 2019
Revi finished up, IP is a tad too low but collied with the sidewall. Should be invisible once the canopy is in place
36
March 7, 2019
The only real fit issue on the Hasegawa kit
37
March 10, 2019
Issue solved
38
March 10, 2019
Rear compartment door added
39
March 10, 2019
Drain pipes added
40
March 10, 2019
Hasegawa exhausts
41
March 10, 2019
Brassin exhausts
42
March 10, 2019
Canopy masked - hours of fiddling!
43
March 10, 2019
It's coming together
44
March 11, 2019
Exhaust comparison: Hasegawa/Barracuda/Eduard
45
March 14, 2019
Hasegawa wingtip light
46
March 14, 2019
Inserted clear sprue
47
March 14, 2019
Brake line added
48
March 25, 2019
Barrcuda exhausts with heat shield from styrene
49
March 25, 2019
Port exhausts with thinned heat shield
50
March 25, 2019
And primed
51
March 25, 2019
Little ghost seam on starboard
52
March 25, 2019
Still work to do on the port side
53
March 29, 2019
Black base
54
March 29, 2019
Almost forgot the stiffener plates
55
March 29, 2019
Bad reaction from the Alclad filler and the black base -> sanding
56
March 29, 2019
Not much effort on the wheel wells
57
March 29, 2019
The ejector pins won't be seen, tried to keep the RLM02 translucent
58
March 29, 2019
White marble coat on the spinner and all the other withe parts, white and yellow for the cowl
59
March 29, 2019
Maybe a tad to much colour on the fuselage band, the colour variation isn't wuite visible in the picture
60
March 29, 2019
Maybe a little bit better on the underside
61
March 30, 2019
Underside camo: RLM76, don't like the Gunze shade, it's almost RLM65ish, 10% light grey didi the trick
62
March 30, 2019
Marble coat
63
March 30, 2019
Blend coat on
64
March 30, 2019
Lots of contrast here!
65
April 3, 2019
RLM79 marble coat applied
66
April 3, 2019
I kept it quite heavy on the sides because the RLM80 mottle will add a lot of contrast
67
April 3, 2019
Not sure on the upper wing mottle - Eagle cal suggest early JG27 style blotches. The original looks more like a mottle.
68
April 4, 2019
RLM79 is on!
69
April 4, 2019
I kept it quite thin to have more contrast when the green is added
70
April 4, 2019
Same for the wings, just the wing root collected too much paint but there will be the exhaust stain, so I don't mind
71
April 9, 2019
First test cut with Tamiya masking sheet - looks promising!
72
April 9, 2019
Unfortunately the crosses came out 2mm too big, despite the correct size in the cutting program
73
May 1, 2019
New masks cut from Oramakask 810
74
May 1, 2019
75
May 1, 2019
masked up for the white
76
May 1, 2019
White marble with off white blend coat
77
May 2, 2019
The final result - not too bad for a first try
78
May 5, 2019
79
May 8, 2019
White and red + white marble for insignia/codes
80
May 8, 2019
All painted and ready for mottling
81
May 10, 2019
Start on the camouflage
82
May 12, 2019
right hand side painted, repairs on the insignia are necessary
83
May 12, 2019
wing camo
84
May 12, 2019
I'll call it: the glamour shot
85
May 19, 2019
86
May 19, 2019
87
June 20, 2019
Putting on the stencils
88
June 20, 2019
Mr. Mark softer ate right through two of the Hasegawa decals -> sanding and repainting..
89
June 26, 2019
90
June 26, 2019
Salt fading - salt grinded over the wet surface
91
June 26, 2019
the result with a light grey on the horizontal surfaces
92
June 26, 2019
and in close up
93
June 27, 2019
preparation for oil dot filtering
94
June 27, 2019
dots placed
95
June 27, 2019
working the colours into the surface, blended right afterwards with thinner
96
June 27, 2019
filter on the left wing vs. previous state on the right wing
97
June 29, 2019
underside washing in place; kept it quite subtle
98
June 29, 2019
the upper surfaces as well - I went with a dark brown with some raw umber in it
99
June 29, 2019
and that's how it looks from a normal vieweing distance
100
June 30, 2019
flat black on the Master MG17 barrels, prepraing for the metal look
101
June 30, 2019
quick spyshot from the bench with the flat coat on
102
July 1, 2019
small stuff for the antenna wire
103
July 1, 2019
everything in place with the antenna line from Uschi
104
July 1, 2019
and here it's in fnished state
105
July 1, 2019
stretched sprue as a light bulb
106
July 1, 2019
Master MG17 barrels - painted flat black, metallic effect applied with lead
107
July 1, 2019
gun stains
108
July 1, 2019
exhaust stains - highly thinned black, followed by dark brown and greyish brown
109
July 1, 2019
canopy holder
110
July 1, 2019
and put into place
111
July 2, 2019
112
July 2, 2019
113
July 2, 2019
114
July 2, 2019
115
July 2, 2019
116
July 2, 2019
117
July 2, 2019
118
July 2, 2019
119
July 2, 2019
120
July 2, 2019

Komentarzy

4 17 February 2019, 15:12

Rui S
Nice. Watching😎

17 February 2019, 20:33

Joachim F.
Thanks! It might take some time - at least until my 1/48 109 is finished - to get started

18 February 2019, 10:30

Rui S
Very nice progress.The streched clear sprue (great idea), the chain, the acetate (the white behind is not painted is it?) Lot's of detail 👍 Looking great.

28 February 2019, 15:39

Joachim F.
The white is painted but only to pop out the printed detail (in black)

28 February 2019, 18:44

Rui S
But It is such an incredible small detail? They look like decal or stencil...

28 February 2019, 23:13

Joachim F.
It's a little bit hard to describe. There's a good photo in this review of the Aires Ki-84 cockpit:
largescaleplanes.com../review.php?rid=1672

3 March 2019, 07:09

Rui S
Thanks for sharing😢

3 March 2019, 12:44

Alec K
Cool project, following 👍

3 March 2019, 17:00

Joachim F.
Thanks - stay tuned😉

4 March 2019, 19:40

Daniel Klink
Georgeous execution...

4 March 2019, 19:45

Holger Kranich
I will follow this build for sure!

5 March 2019, 13:47

Spanjaard
looking good, very nice cockpit

6 March 2019, 09:31

Joachim F.
Thank you very much mates.
The latest cockpit shots are online.

7 March 2019, 13:58

Spanjaard
👍

8 March 2019, 14:42

Soeren R.
Count me in😉

14 March 2019, 11:57

Holger Kranich
Looks very promising to me!

29 March 2019, 19:30

Clifford Keesler
Following.

30 March 2019, 18:36

Richmond
Superb paintwork

31 March 2019, 11:58

Joachim F.
Thanks guys - it'll take some days to get the upperside camo done. A little hand injury is making the mottling a real pain.

31 March 2019, 17:38

ForestFan
Looking great so far

31 March 2019, 18:58

Erik Leijdens
Beautiful paint job !

4 April 2019, 19:25

Olivier
Fabulous interior !

9 April 2019, 19:26

Clifford Keesler
Looking awesome so far.

10 April 2019, 00:12

Holger Kranich
Is that a pre-cut masking sheet?

10 April 2019, 09:53

Joachim F.
Thanks mates!
@Holger: No - I did cut the masks with a Silhouette Portrait plotter - at least I tried!

10 April 2019, 19:05

Alec K
I just got the Cameo plotter, thinking about cutting masks on it as well. Looks like there will be challenges 😄

11 April 2019, 12:50

Joachim F.
I had a discussion on largescaleplanes on this and one problem is the Tamiya sheet. It's just too tacky - I ordered Oramask 810 and will do another mask set with this material. It's supposed to be close to the vinyl of the montex masks

11 April 2019, 16:43

Rui S
Nice progress 👍

6 May 2019, 20:37