Tunguska, W-model 1/72
![Album image #1 Album image #1](/albums/img/7/9/4/593794-11032-40-720.jpg)
Basic hull as per kit, doesn't fit the upper hull
![Album image #2 Album image #2](/albums/img/7/9/5/593795-11032-16-720.jpg)
almost a mm has to disappear from both sides
![Album image #3 Album image #3](/albums/img/7/9/6/593796-11032-38-720.jpg)
rear plate doesn't fit too
![Album image #4 Album image #4](/albums/img/7/9/7/593797-11032-13-720.jpg)
Preparation of the necessary cuts
![Album image #5 Album image #5](/albums/img/7/9/8/593798-11032-13-720.jpg)
dryfit
![Album image #6 Album image #6](/albums/img/7/9/9/593799-11032-99-720.jpg)
the furthest sidewall is too long
![Album image #7 Album image #7](/albums/img/8/0/1/593801-11032-96-720.jpg)
removed the inside material
![Album image #8 Album image #8](/albums/img/8/0/3/593803-11032-12-720.jpg)
dryfit of the rear plate. aligned it to preserve the details. There's still a 4mm gap
![Album image #9 Album image #9](/albums/img/8/0/0/593800-11032-13-720.jpg)
Rear plate cut in half
![Album image #10 Album image #10](/albums/img/8/0/2/593802-11032-12-720.jpg)
upper part glued in place
![Album image #11 Album image #11](/albums/img/8/0/4/593804-11032-24-720.jpg)
first glued the outer parts in place, then centered the mid part
![Album image #12 Album image #12](/albums/img/8/0/5/593805-11032-73-720.jpg)
some necessary filling was needed...
![Album image #13 Album image #13](/albums/img/8/1/3/593813-11032-31-720.jpg)
this sidewall protrudes about 0.5mm... more filling and sanding...
![Album image #14 Album image #14](/albums/img/8/6/2/595862-11032-33-720.jpg)
Rocket launcher tubes are a bit... euh... distorted... Awaiting some 2.4/2.5mm round styrene to scratch these
![Album image #15 Album image #15](/albums/img/8/6/3/595863-11032-47-720.jpg)
rear is round
![Album image #16 Album image #16](/albums/img/8/6/4/595864-11032-50-720.jpg)
cut off the ends, overall shape on this side is oval...
Comments
5 April 2019, 07:46
![](/profiles/img/user-s.jpg)
Started this new one from W-model. To be honest... a bit of a let down, a lot of rework is needed. Had contact about it with the manufacturer, and they will upgrade the molds. They also offered new parts, but I wanted to try to solve it, and have the new parts as a back-up plan...
5 April 2019, 08:00
![](/profiles/img/26775-480-s.jpg)
I'm following!
You have done a lot of reworks still at the beginning of the build! It will be a really sweating work! I hope at the end it will be a fun!
5 April 2019, 14:31
![](/profiles/img/user-s.jpg)
Thx guys... Also hope it will pay off in the end.
@Dave, it is a new kit, think I have one of the first made...
5 April 2019, 15:23
![](/profiles/img/user-s.jpg)
Started work on the rocket launchers... think these will need to be rebuilt to...
11 April 2019, 10:48