A-4F, 1:144
![Album image #1 Album image #1](/albums/img/6/4/6/806646-11032-12-720.jpg)
Main parts
![Album image #2 Album image #2](/albums/img/6/4/7/806647-11032-27-720.jpg)
rest of the parts
![Album image #3 Album image #3](/albums/img/6/4/8/806648-11032-24-720.jpg)
decals from the kit
![Album image #4 Album image #4](/albums/img/6/4/9/806649-11032-25-720.jpg)
Cut out the slots
![Album image #5 Album image #5](/albums/img/6/5/0/806650-11032-18-720.jpg)
wing halves joined
![Album image #6 Album image #6](/albums/img/6/5/1/806651-11032-84-720.jpg)
flare dispensers need to be recessed
![Album image #7 Album image #7](/albums/img/6/5/2/806652-11032-89-720.jpg)
first mark the size with a scalpel, next put the blade with the straight edge to the outside and deepen the borders. That way you create a kind off barrier when you scrape/cut away the inside.
![Album image #8 Album image #8](/albums/img/6/5/3/806653-11032-80-720.jpg)
ready for dryfit
![Album image #9 Album image #9](/albums/img/6/5/4/806654-11032-35-720.jpg)
and glued
![Album image #10 Album image #10](/albums/img/6/5/5/806655-11032-81-720.jpg)
Not a big fan of prepainted cockpits, but in this case it saves a lot of work....
![Album image #11 Album image #11](/albums/img/6/5/6/806656-11032-23-720.jpg)
Cockpit fitted and openings in the wings filled with putty. droptanks are dryfit. These consist of 3 parts, and the tailpart has some serious sinkmarks...
![Album image #12 Album image #12](/albums/img/8/6/2/809862-11032-34-720.jpg)
PE wheelbays assembled and main hull parts assembled
![Album image #13 Album image #13](/albums/img/8/6/7/809867-11032-49-720.jpg)
this join is a hard one to clean up, so scraping, adding CA, scraping sanding.... to achieve a presentable result...
![Album image #14 Album image #14](/albums/img/8/6/3/809863-11032-51-720.jpg)
satisfied
![Album image #15 Album image #15](/albums/img/8/6/4/809864-11032-55-720.jpg)
plugs in place, 20mm guns removed, sanded smooth and tested with paint...
![Album image #16 Album image #16](/albums/img/8/7/1/809871-11032-39-720.jpg)
ready
![Album image #17 Album image #17](/albums/img/8/6/8/809868-11032-76-720.jpg)
started removing some parts from te seat to replace them with PE
![Album image #18 Album image #18](/albums/img/8/6/5/809865-11032-43-720.jpg)
![Album image #19 Album image #19](/albums/img/8/7/4/809874-11032-34-720.jpg)
and with all belts etc added
![Album image #20 Album image #20](/albums/img/8/6/6/809866-11032-75-720.jpg)
prepainted PE is euh... very delicate to work with....
![Album image #21 Album image #21](/albums/img/8/7/5/809875-11032-44-720.jpg)
and bangseat in place... also the hud was added
![Album image #22 Album image #22](/albums/img/8/6/9/809869-11032-69-720.jpg)
original canopy
![Album image #23 Album image #23](/albums/img/8/7/3/809873-11032-61-720.jpg)
and some carefull cutting later
![Album image #24 Album image #24](/albums/img/8/7/0/809870-11032-48-720.jpg)
![Album image #25 Album image #25](/albums/img/8/7/2/809872-11032-55-720.jpg)
one tiny thing...
![Album image #26 Album image #26](/albums/img/2/9/7/811297-11032-16-720.jpg)
added some wire to the front legg
![Album image #27 Album image #27](/albums/img/2/9/8/811298-11032-82-720.jpg)
and to the main leggs too
![Album image #28 Album image #28](/albums/img/2/3/6/813236-11032-62-720.jpg)
basecolors
![Album image #29 Album image #29](/albums/img/2/3/7/813237-11032-30-720.jpg)
washed
![Album image #30 Album image #30](/albums/img/4/7/1/824471-11032-94-720.jpg)
![Album image #31 Album image #31](/albums/img/4/7/3/824473-11032-30-720.jpg)
So I cut the original part in pieces, drilled a small hole (0.5mm in a 0.6mm plastic part...) not that deep, but...
![Album image #32 Album image #32](/albums/img/4/7/2/824472-11032-67-720.jpg)
bended it according to the drawing
![Album image #33 Album image #33](/albums/img/4/7/4/824474-11032-40-720.jpg)
glued all parts into place and bummer... to long, bend isn't good etc... why a wrong template then???
![Album image #34 Album image #34](/albums/img/4/7/5/824475-11032-69-720.jpg)
and adapted
![Album image #35 Album image #35](/albums/img/1/5/4/825154-11032-43-720.jpg)
Reworked the refueling probe... could be done better. Had to heat the brass, it couldn't be bent in such sharp corner without breaking... The material get's softer, hence I loose my rigidity... the wifey will be pleased ... 😉
![Album image #36 Album image #36](/albums/img/1/5/3/825153-11032-24-720.jpg)
it is small: 84mm
![Album image #37 Album image #37](/albums/img/1/5/5/825155-11032-28-720.jpg)
canopy added... was a dread... seat sat a little to heigh, so had to file a bit off... then this breaks off, that breaks off, then this again...
![Album image #38 Album image #38](/albums/img/1/5/6/825156-11032-57-720.jpg)
al closed up... to rework the scribing or not... detail is pretty soft
Comments
2 10 July 2020, 07:00
![](/profiles/img/26441-134-s.jpg)
Oh, I've got five of these in the stash... sign me up for the how to course.
18 July 2020, 12:08
![](/profiles/img/user-s.jpg)
thx Lukasz.
Next up was the refueling probe. That was a plastic part, mainly 0.5mm diameter, that needed to be bent... recipe for disaster I thought, so I've replaced it with some brass rod (more solid then copper wire)
The template from Eduard isn't up to scale, and shows the wrong bend so I had to change in the end...
11 August 2020, 14:29
![](/profiles/img/user-s.jpg)
Redid the refueling probe... it extended too far, and still wasn't right... then closed the canopy before painting... did some dryfitting before, but the seat was a tad to heigh, so had to remove it, some unwanted thing were also removed in the process, so from an easy job to a full afternoon... finally it was closed up... now, deepen the panellines or not...
12 August 2020, 14:37
![](/profiles/img/user-s.jpg)
Something went wrong with my AB and it spilled a lot of Paint on the model. Now I'm busy restoring the damage done before going on with the paintjob.
31 August 2020, 13:26