Notícias
Dom S.
possui este item
possui este item
"Short sleep Panzergrenadier"
Power Naps of Panzergrenadiers 1 driver, 1 Feldwebel and 4 figure Panzergrenadier. SOGA Miniatures 1:35
SOGA-13 2017 Produto novo 12 August, 15:41
CF104
possui este item
possui este item
S-3 "Late" Engine Fan & Inlet Set For 48th ESCI/AMT/Italeri S-3 Vikings
Sierra Hotel Models 1:48
48404 2010 Produto novo 12 August, 15:39
CF104
possui este item
possui este item
Lockheed
S-3 Viking - Landing Gear for ESCI, Italeri Scale Aircraft Conversions 1:48
48006 200x Produto novo 12 August, 15:39
Simon Nagorsnik
adicionou um novo álbum de fotos.
adicionou um novo álbum de fotos.
7 11 August, 15:27
Mr D
Nice little job, fiddly to do l built a ship n it was difficult, l had to get a tweezers set.
Good stuff 👌
Nice little job, fiddly to do l built a ship n it was difficult, l had to get a tweezers set.
Good stuff 👌
11 August, 15:45
Skyhiker
adicionou um novo álbum de fotos.
adicionou um novo álbum de fotos.
15 imagens
Foke Wulf 190 F-8 (1997 tooling)Novo: 12 August, 15:37 1:72
Primer is on. A few minor adjustments are needed around the canopy.
Projeto: Focke-Wulf Fw 190 F-8
18 1 August, 17:22
Skyhiker
For a relatively new kit I am surprised on how much flash and fitting issues this kit has.
For a relatively new kit I am surprised on how much flash and fitting issues this kit has.
2 August, 04:46
Skyhiker
It's really hard for me to fight off the urge to correct the structural issues with this kit. But I promised myself I would make this one out of the box.
It's really hard for me to fight off the urge to correct the structural issues with this kit. But I promised myself I would make this one out of the box.
2 August, 11:32
Patrick Hagelstein
I've seen that promise before Skyhiker! 😂 Good luck keeping this one OOB! 😉👍🏼
I've seen that promise before Skyhiker! 😂 Good luck keeping this one OOB! 😉👍🏼
2 August, 20:39
Sergio Ordonez
Mate, I think you should put the windshield uspside down. The ángel does not cope with the real one as I see on photographs.
Mate, I think you should put the windshield uspside down. The ángel does not cope with the real one as I see on photographs.
2 August, 20:52
Skyhiker
Unfortunately it looks even worse the other way around. The idiot engineers at Revell should be fired.
Unfortunately it looks even worse the other way around. The idiot engineers at Revell should be fired.
2 August, 21:04
Sergio Ordonez
Well, I had some work with French engineers and I know shit happens. Could you take a photo with this one in the other position?
Well, I had some work with French engineers and I know shit happens. Could you take a photo with this one in the other position?
2 August, 21:09
Sergio Ordonez
drive.google.com/fil..J9/view?usp=drivesdk
The windshield is not an isoscelles triangle so the windshield has not a 45 degree ángel over the capot. Please, see these example of a TA-152 (and please, mind It is 35 years old and I was only 13 when I drestroyed It).
I think an easy solution can be made. I do not want any mate to be anoyed by an engineering issue. I had them everyday (it's my job, Factory engineering problem solving, known as 'shit managing") and It can destroy your mojo.
drive.google.com/fil..J9/view?usp=drivesdk
The windshield is not an isoscelles triangle so the windshield has not a 45 degree ángel over the capot. Please, see these example of a TA-152 (and please, mind It is 35 years old and I was only 13 when I drestroyed It).
I think an easy solution can be made. I do not want any mate to be anoyed by an engineering issue. I had them everyday (it's my job, Factory engineering problem solving, known as 'shit managing") and It can destroy your mojo.
2 August, 21:23
Skyhiker
After several hours of sculpting I got the canopy to fit better. I will continue with it tomorrow.
After several hours of sculpting I got the canopy to fit better. I will continue with it tomorrow.
3 August, 02:12
Sergio Ordonez
Your mojo works, mate! Now you have became a great problem solver!
On the other hand, I think another 3D engineering guy needs to stop drinking and 20 years of 2D drafting. The fitting is worse than I could imagine. But I see is no a problem for a seasoned mate like you. Great work, mate!
Your mojo works, mate! Now you have became a great problem solver!
On the other hand, I think another 3D engineering guy needs to stop drinking and 20 years of 2D drafting. The fitting is worse than I could imagine. But I see is no a problem for a seasoned mate like you. Great work, mate!
3 August, 05:17
Nicolas
Following. I build this kit several times in older versions. The fit of the canopy is realy sh*t. My solution was (with about 10 years) to sand the backside of the windshild till it fitted. Of corse so most of the frame is missing.
Following. I build this kit several times in older versions. The fit of the canopy is realy sh*t. My solution was (with about 10 years) to sand the backside of the windshild till it fitted. Of corse so most of the frame is missing.
3 August, 05:31
Thomas Kolb
What a struggle! It reminds me of some Heller and Amodel kits. But it looks that you manage to coax it into shape!
What a struggle! It reminds me of some Heller and Amodel kits. But it looks that you manage to coax it into shape!
3 August, 07:11
Skyhiker
Sergio the TA 152 had a very different canopy than the 190. The 152 was designed for high altitude flying, was pressurized and had double panes.
Sergio the TA 152 had a very different canopy than the 190. The 152 was designed for high altitude flying, was pressurized and had double panes.
4 August, 10:03
Sergio Ordonez
Thanks you, Skyhiker: I think I can remember now, as I researched about FW190 and TA152 black in the 90's. Also, canopy is bubble-shapped. Sorry, my FW190 Mustang have been gone forever, I expent the night trying to find It, just to find my solution, but I think only the reta of the TA152 has survived.
Thanks you, Skyhiker: I think I can remember now, as I researched about FW190 and TA152 black in the 90's. Also, canopy is bubble-shapped. Sorry, my FW190 Mustang have been gone forever, I expent the night trying to find It, just to find my solution, but I think only the reta of the TA152 has survived.
4 August, 14:05
Mr D
You done a better job of the seat belts than l did 🤣. The cockpit glass on my model was not very clear!
Looking good, ... Thanks for uploading 👍👍👍
You done a better job of the seat belts than l did 🤣. The cockpit glass on my model was not very clear!
Looking good, ... Thanks for uploading 👍👍👍
11 August, 15:13
Skyhiker
Mr D did you also have so much trouble with the canopy? I read in the kit review at the bottom of the page that it was bad. I really wish the reviews would be moved up because I always forget about them. It took me quite a while to get the canopy to work. It needed a lot of reshaping to look right.
Mr D did you also have so much trouble with the canopy? I read in the kit review at the bottom of the page that it was bad. I really wish the reviews would be moved up because I always forget about them. It took me quite a while to get the canopy to work. It needed a lot of reshaping to look right.
11 August, 17:40
Skyhiker
I decided to make my own blueprint for this plane. So, that's taking up a lot of my time at the moment.
I decided to make my own blueprint for this plane. So, that's taking up a lot of my time at the moment.
11 August, 17:42
Mr D
Hi, yes l had trouble too, l did a dry fit before paint, and l had to take a combination off the glass n some off fuselage, and had to use a bit of UV clear resin.
I got it to fit in the end, but it's not very clear to see through.
I had a bit missing of my engine fan too, had to make it up with super glue gell.
Hi, yes l had trouble too, l did a dry fit before paint, and l had to take a combination off the glass n some off fuselage, and had to use a bit of UV clear resin.
I got it to fit in the end, but it's not very clear to see through.
I had a bit missing of my engine fan too, had to make it up with super glue gell.
11 August, 17:48
Skyhiker
adicionou um novo álbum de fotos.
adicionou um novo álbum de fotos.
9 imagens
Tic Tac UAP (Scratch build)Novo: 12 August, 15:34 1:72
Primer down and ready for some paint!
Projeto: Tic Tac UAP
Scratchbuilt
9 31 July, 21:12
Skyhiker
Welcome gents. I'm not sure if these are the guys with the probe or if they're the ones who steal cows. They definitely don't want to be taken to our leader.
Welcome gents. I'm not sure if these are the guys with the probe or if they're the ones who steal cows. They definitely don't want to be taken to our leader.
2 August, 04:43
Cdallas2
adicionou um novo álbum de fotos.
adicionou um novo álbum de fotos.
10 imagens
Choo-chooNovo: 11 August, 21:27 1:87
Weathering and coal car left
Projeto: Big Boy Locomotive
12 7 July, 06:16
Cdallas2
Decided not to get too far before assembling and painting sections. Lots of parts look VERY similar so confusing myself could be an issue.
Decided not to get too far before assembling and painting sections. Lots of parts look VERY similar so confusing myself could be an issue.
8 July, 05:11
Christian W » Solicitações de recursos
I found an issue: when I look up a model kit (for example "revell shelby series" - SCM Search: revell shelby series) I get an overview like supposed. Then I scroll down to the section with projects. In this case there is only one listed. But I know, that my brother built two.
I switch to the kit (07379) and there are his two project (Shelby Series 1 (Revell 07379, 1:25))
So the listing in the overview has some missing projects. 🙂
I found an issue: when I look up a model kit (for example "revell shelby series" - SCM Search: revell shelby series) I get an overview like supposed. Then I scroll down to the section with projects. In this case there is only one listed. But I know, that my brother built two.
I switch to the kit (07379) and there are his two project (Shelby Series 1 (Revell 07379, 1:25))
So the listing in the overview has some missing projects. 🙂
Implementado
1 15 January, 06:05
scalemates
We only find projects based on their title/description and not based on the brand of a kit.
The reason you find one because it has "Revell" in the title
I'll see if I can make this automatic
We only find projects based on their title/description and not based on the brand of a kit.
The reason you find one because it has "Revell" in the title
I'll see if I can make this automatic
20 January, 15:33
Christian W
Maybe you can use the connection of a kit (number) to a project? Would this be possible?
From the doing the member is able to connect several kits to any project. So maybe the other way round (read out, which connections a kit to what project(s) or (?) album it has) can solve that?
Can you follow my thoughts?
Maybe you can use the connection of a kit (number) to a project? Would this be possible?
From the doing the member is able to connect several kits to any project. So maybe the other way round (read out, which connections a kit to what project(s) or (?) album it has) can solve that?
Can you follow my thoughts?
24 January, 22:08
Martin Oostrom
adicionou um novo álbum de fotos.
adicionou um novo álbum de fotos.
54 imagens
WIP Köln trailerNovo: 12 August, 15:26 1:24
Mr Topcoat acrylic gloss, straight from the can
Projeto: DAF 95 XF & Trailer "Köln Truck"
21 16 May, 18:27
Bozzer
I'm glad to see, that it's not just me, who does all this type of prep work. I've spent far too much time and money, on tools, gizmo's and fabrication of various things, just to try and speed up this process. Yet, I still end up falling back to the back of a #11 knife blade!
I'll hang around for this one mate, mainly to see the outcome of those amazing decals. But also to watch how the trailer goes together?
I helped my son build the Spacecab, way back in the early 2000's. He didn't enjoy it and abandoned his efforts 🙁 No wonder he became a plumber 😛
I'm glad to see, that it's not just me, who does all this type of prep work. I've spent far too much time and money, on tools, gizmo's and fabrication of various things, just to try and speed up this process. Yet, I still end up falling back to the back of a #11 knife blade!
I'll hang around for this one mate, mainly to see the outcome of those amazing decals. But also to watch how the trailer goes together?
I helped my son build the Spacecab, way back in the early 2000's. He didn't enjoy it and abandoned his efforts 🙁 No wonder he became a plumber 😛
16 May, 23:58
Martin Oostrom
Kerry Cox taught Peter Hardy and Peter taught me: "Better remove those lines, you'll always know they're there."
I mostly use the cutting edge of the blade to scrape, I'll try the back sometime.
I assembled the chassis today and it seems perfectly straight. A lot of work remains before I can start on the decals.
Kerry Cox taught Peter Hardy and Peter taught me: "Better remove those lines, you'll always know they're there."
I mostly use the cutting edge of the blade to scrape, I'll try the back sometime.
I assembled the chassis today and it seems perfectly straight. A lot of work remains before I can start on the decals.
17 May, 20:51
Bozzer
If you draw the edge, of the back of the blade, it gives you a nice smooth, flat surface. It also doesn't dull your sharp blade? After a while, it becomes second nature. I have found, that those nasty mold lines, show up even more, when paint is applied? Even when I glue two parts together, it's always the back of the knife, that deals with the seam. You should definitely try it, and see if you notice the difference.
If you draw the edge, of the back of the blade, it gives you a nice smooth, flat surface. It also doesn't dull your sharp blade? After a while, it becomes second nature. I have found, that those nasty mold lines, show up even more, when paint is applied? Even when I glue two parts together, it's always the back of the knife, that deals with the seam. You should definitely try it, and see if you notice the difference.
17 May, 22:21
Martin Oostrom
The doctor is in 😄
I managed some work on the axles Tuesday evening and I had half a day to myself yesterday. So I built the box with a lot of added plastic to get everything squared. I'll be sanding the outside and I don't want the thing to fold.
The mudflaps were unconvincing , so I went to town on them. Your opinions please?
The doctor is in 😄
I managed some work on the axles Tuesday evening and I had half a day to myself yesterday. So I built the box with a lot of added plastic to get everything squared. I'll be sanding the outside and I don't want the thing to fold.
The mudflaps were unconvincing , so I went to town on them. Your opinions please?
26 May, 07:56
Bozzer
I've heard of guys, filling in reefers, with expanding foam?
I've never personally done it, because I like the option of opening doors. Those mudflaps look so much better now, too.
I've heard of guys, filling in reefers, with expanding foam?
I've never personally done it, because I like the option of opening doors. Those mudflaps look so much better now, too.
26 May, 19:34
Martin Oostrom
Mmm, insulation foam in a reefer….
There is/was a load of cyanide in that stuff. Not something I want to emit in my hobby room.
My 2k also contains cyanide, but those vapours are mainly vented outside
Mmm, insulation foam in a reefer….
There is/was a load of cyanide in that stuff. Not something I want to emit in my hobby room.
My 2k also contains cyanide, but those vapours are mainly vented outside
27 May, 14:05
Bozzer
I have never checked mate, and I've used it for sealing gaps, etc, for decades? However, I've definitely not used it on any models. In fairness though, all my current reefers are from AMT. I love the fact that they use 1 piece plastic, for the sides, base and top. It definitely makes them sturdy. I do have a few Italeri reefers though, and I was thinking about lining them with thin plastic? I don't want to compromise the look, so I thought maybe some 1mm sheet, would work? What do you think mate?
I have never checked mate, and I've used it for sealing gaps, etc, for decades? However, I've definitely not used it on any models. In fairness though, all my current reefers are from AMT. I love the fact that they use 1 piece plastic, for the sides, base and top. It definitely makes them sturdy. I do have a few Italeri reefers though, and I was thinking about lining them with thin plastic? I don't want to compromise the look, so I thought maybe some 1mm sheet, would work? What do you think mate?
27 May, 20:21
Martin Oostrom
Lining with 1mm sheet is a possibility, but … see my new picture. On both sides there are two half rods running the whole length of the trailer and the ceiling is littered with protruding ejection marks.
The floor is smooth as the ejection marks are on the underside.
This Revell edition has water slide decals, the Italeri reefer I have has two big stickers for each side. Will be hell to line up, so I'll probably paint something.
Lining with 1mm sheet is a possibility, but … see my new picture. On both sides there are two half rods running the whole length of the trailer and the ceiling is littered with protruding ejection marks.
The floor is smooth as the ejection marks are on the underside.
This Revell edition has water slide decals, the Italeri reefer I have has two big stickers for each side. Will be hell to line up, so I'll probably paint something.
27 May, 20:54
Bozzer
On large decals, it's best to cut them into 3. It just makes things easier. I honestly wouldn't have a clue what to do with stickers though? That's exactly what I have, on my Smokey and the Bandit 2 trailer.
Which reminds me...
Jerry from Modeltruckin, is retiring. Last orders are being taken upto end of July. Get them decals ordered mate, before you can't get them again!
On large decals, it's best to cut them into 3. It just makes things easier. I honestly wouldn't have a clue what to do with stickers though? That's exactly what I have, on my Smokey and the Bandit 2 trailer.
Which reminds me...
Jerry from Modeltruckin, is retiring. Last orders are being taken upto end of July. Get them decals ordered mate, before you can't get them again!
27 May, 21:26
Bozzer
I just took a closer look at your pictures. I see those rails now. I'm guessing that they were a feature, to stop pallets from ramming up tight to the side, on the 1:1 version? The injection pin marks, I can Dremel away. You've actually got me thinking about digging out one of my reefers now, lol
I just took a closer look at your pictures. I see those rails now. I'm guessing that they were a feature, to stop pallets from ramming up tight to the side, on the 1:1 version? The injection pin marks, I can Dremel away. You've actually got me thinking about digging out one of my reefers now, lol
27 May, 21:34
Martin Oostrom
In the real one, there will be a strip with slits to secure the cargo. But those are generally not that high and low. See picture.
In the real one, there will be a strip with slits to secure the cargo. But those are generally not that high and low. See picture.
28 May, 06:00
Bill Newcomer
Late to the party. (I have been really busy with my wife's garden and my 1:1 car) Following. Making your box square and straight looks like quite the endeavor.
Late to the party. (I have been really busy with my wife's garden and my 1:1 car) Following. Making your box square and straight looks like quite the endeavor.
31 May, 04:12
Martin Oostrom
Dry fitting the door showed a small gap between them. I later added a strip of styrene to the back. Stiffening the doors by accident.
I removed the moulded rear lights, only realising too late that they're hollow. A thin sheet of styrene helped. I also glued a strip to the storage bins. Too much sanding otherwise. Now all trailer parts are ready for painting.
Dry fitting the door showed a small gap between them. I later added a strip of styrene to the back. Stiffening the doors by accident.
I removed the moulded rear lights, only realising too late that they're hollow. A thin sheet of styrene helped. I also glued a strip to the storage bins. Too much sanding otherwise. Now all trailer parts are ready for painting.
16 June, 18:25
Lode Schildermans
Definitely impressed, Martin. Smart building by improving stability in the beginning of the build. I particularly like the improvements with styrene
Definitely impressed, Martin. Smart building by improving stability in the beginning of the build. I particularly like the improvements with styrene
17 June, 06:17
Bozzer
I wonder if that PE is going to be the bars and locking system, for the back doors?
I wonder if that PE is going to be the bars and locking system, for the back doors?
18 June, 02:24
Martin Oostrom
Primer's on! It took over 4 hours to paint the truck and trailer in my tiny booth.
Primer's on! It took over 4 hours to paint the truck and trailer in my tiny booth.
18 July, 16:19
Lode Schildermans
But the result is a success. Looking forward to see your progress of this big one
But the result is a success. Looking forward to see your progress of this big one
19 July, 05:39
Martin Oostrom
First colours are here. Tamiya bright red, Tamiya silver and not shown, Tamiya aluminium straight from the can on the reefer itself.
First colours are here. Tamiya bright red, Tamiya silver and not shown, Tamiya aluminium straight from the can on the reefer itself.
19 July, 13:50
Martin Oostrom
For the first time in forever I follow the colour callouts from the instructions, and now my choices are excellent. Makes me wonder…
Enjoy the colours while you can, this thing will be wrapped in decals when she's done.
For the first time in forever I follow the colour callouts from the instructions, and now my choices are excellent. Makes me wonder…
Enjoy the colours while you can, this thing will be wrapped in decals when she's done.
20 July, 08:31
Bozzer
Lol, maybe because it's more true to life?
Although I have to admit, I've crawled under a few trailers, and they were all the same, light rust/brown colour. Even on fleet management, the chassis and underneath, never get washed. I do a lot of work for a global logistics company and their trucks always look clean, but they're not. My brother works for a national retailer, driving big rigs. I asked him when he washes the underside of his trailer? His answer was priceless, but unfortunately, unprintable 😉
Lol, maybe because it's more true to life?
Although I have to admit, I've crawled under a few trailers, and they were all the same, light rust/brown colour. Even on fleet management, the chassis and underneath, never get washed. I do a lot of work for a global logistics company and their trucks always look clean, but they're not. My brother works for a national retailer, driving big rigs. I asked him when he washes the underside of his trailer? His answer was priceless, but unfortunately, unprintable 😉
20 July, 13:50
Martin Oostrom
I actually had red oxide primer in mind for the red parts, but didn't at the last moment!
I also never wash the underside of my car. And I've worked in port, so I can imagine some colourful language.
Done with airbrushing for now. Only some detail painting to do.
And after curing, it's decals time!
I actually had red oxide primer in mind for the red parts, but didn't at the last moment!
I also never wash the underside of my car. And I've worked in port, so I can imagine some colourful language.
Done with airbrushing for now. Only some detail painting to do.
And after curing, it's decals time!
20 July, 14:11
Bozzer
Mate, please do as Goldman suggested on your other thread, and take pictures of these?
It's definitely worth a try? I can't bear to hear the screams, if the decals spray doesn't work.
We need you to be successful on this, to raise the bar, and give the rest of us, something to reach for?
God speed, my friend, and good luck 👍
Mate, please do as Goldman suggested on your other thread, and take pictures of these?
It's definitely worth a try? I can't bear to hear the screams, if the decals spray doesn't work.
We need you to be successful on this, to raise the bar, and give the rest of us, something to reach for?
God speed, my friend, and good luck 👍
3 August, 21:11
Martin Oostrom
It seems to work on the first two pieces 🤞🏻
I'll let these cure for a while, to avoid moving them when doing the two large decals
It seems to work on the first two pieces 🤞🏻
I'll let these cure for a while, to avoid moving them when doing the two large decals
4 August, 11:33
Spanjaard
mission accomplished my friend, well done!!! now let's do (tomorrow?) the other side 🙂
mission accomplished my friend, well done!!! now let's do (tomorrow?) the other side 🙂
4 August, 16:40
Bozzer
Sorry for the FB link, but I think that looks awesome! And really, they made it look so easy?
Sorry for the FB link, but I think that looks awesome! And really, they made it look so easy?
4 August, 21:40
Bozzer
Martin, you pulled it out of the bag!
I was nervous for you, on those big decals, but mate, you made it look like a pro!
Kudos to you, and I hope you celebrate with a few cold beers!
Martin, you pulled it out of the bag!
I was nervous for you, on those big decals, but mate, you made it look like a pro!
Kudos to you, and I hope you celebrate with a few cold beers!
4 August, 21:44
schecter87
As I can see - you're using Micro Sol solution. Have you tried Tamiya Super Strong in a black bottle (It should be used carefully and needs a bit of experience to use, but it softens decal very fast)? When I first used Mark Fit Super Strong, it was like a revelation to me 🙂 But I never used Micro Sol, so I don't know of how it works.
As I can see - you're using Micro Sol solution. Have you tried Tamiya Super Strong in a black bottle (It should be used carefully and needs a bit of experience to use, but it softens decal very fast)? When I first used Mark Fit Super Strong, it was like a revelation to me 🙂 But I never used Micro Sol, so I don't know of how it works.
5 August, 10:40
Martin Oostrom
That truck is awesome Bozzer! Really enjoyed that video.
Only the starboard large decal left 🤞🏻
And then hoping that the clear coat won't do anything funny. I got two spray cans of Mr Top Coat gloss. According to the internet, that should do fine 🤞🏻
Hi Scheckter, I use a combination of micro sol and heat. Apply some Sol, let it work a little, press with a soft brush or que tip. Repeat a hundred times or more to get everything where I want it.
I'm careful with these old decals and extra hot decal softener.
That truck is awesome Bozzer! Really enjoyed that video.
Only the starboard large decal left 🤞🏻
And then hoping that the clear coat won't do anything funny. I got two spray cans of Mr Top Coat gloss. According to the internet, that should do fine 🤞🏻
Hi Scheckter, I use a combination of micro sol and heat. Apply some Sol, let it work a little, press with a soft brush or que tip. Repeat a hundred times or more to get everything where I want it.
I'm careful with these old decals and extra hot decal softener.
5 August, 15:00
Martin Oostrom
Clearcoat with Mr Topcoat acrylic gloss. straight from the rattle can, due to spray booth size limitations. Not so sure yet about the result.
Clearcoat with Mr Topcoat acrylic gloss. straight from the rattle can, due to spray booth size limitations. Not so sure yet about the result.
12 August, 15:28
CF104
possui este item
possui este item
BAE Lightning - Seat with Safety Belts
Quickboost 1:48
QB 48 301 12 August, 15:23
/pt/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=pt
35
35
/pt/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo