Notícias

Greg Baker
After a quick study of Uwe's album… here we go!

Robert Podkoński
Taking a seat!

Alex K
So do I!

Uwe Kaeding
Go for it Greg - not much room for wiring though! I also thought you'd go for one of the AVI/LF styrene kits.

Greg Baker
If I hadn't got excited and spent $35 on this kit 5 years ago after seeing your build, I probably would've gone with the styrene - they do look really good. Oh, well, we work with what we've got...

Of course... that's only until I figure out that the correct version of the Puss Moth is the Mk. V and not the Mk. XIV and then I can't unsee the problems... 🙂

Greg Baker
As for the wiring, I've drilled out the engine cowling to create enough room to slot in the DC motor. It's VERY tight and I was very careful not to breach the surface. I haven't tested it yet, but I think I was able to get close enough. The small DC motors always have such a small shaft, which can be helpful but sometimes creates a challenge. I'll run two thin wires out and then hide them behind a small, scratchbuilt control panel. Then under the styrene floor and down through a hole in the underside of the fuselage. I'll have to put a resistor on it in the base, otherwise the motor will likely spin this little plan apart. 🙂

Живко Джаков
This is interesting! I'm following. I have a question. How do you connect the motor to the propeller?

Greg Baker
Because I can't quite get the DC motor out of the engine cowling due to the size, I'll have to add a styrene rod to the propellor and then have it go into the cowling. To attach it to the motor itself, I'll likely drill a small hole (about the same diameter as the DC motor shaft) into the short styrene rod and then fit it to the motor shaft with a tiny bit of CA glue (making sure not to get the glue INTO the motor itself). Then I'll glue to styrene rod to the propellor. It'll be tricky to keep everything centred, otherwise the spin will be off. I'll take lots of pictures to show the process... if it works. 😉

Живко Джаков
I am asking about the centering. I have some experience with DC motors. I have several similar ones collected from children's toys, but I dare not try.

Finn
Joining

Greg Baker
Centering... well now... usually what I do is drill a hole as close to the centre as I can manage it... then I drill a little bit this way... then a little bit that way... then I slice the rod until I get a bit that is arguably in the centre...

Then I ignore the wobble. 🙂

Thomas Espe
👀

Greg Baker
Alright. Some progress. I have out some of the cockpit to make room for the extra windows. I was as eloquent as Uwe, so I covered my mistakes up with some thin sheet polystyrene. Put in some wires to reinforce the wings, and got the propeller spinning. So far so good, I think.

Matthew A
Cor

Cuajete
I can't miss this!

Greg Baker
Wings attached and engine mounted.

Casey Beckett
OOH. An Omega kit - I have one of their BN Islanders - Watching this one.

Greg Baker
Got the fuselage more or less put together and painted the interior. Next up will be fitting in the windows… if I'm not back in a day or two, notify the authorities. 😉

Живко Джаков
If I have to report you missing to North Shore Rescue it will be easy.

Cuajete
The frame of those windows seems very fragile being resin. You have great skill, Greg!

Greg Baker
Thanks Cuajete - the resin is quite tricky to work with and I had to add in some extra windows, so it was a bit touch and go. I did copy Uwe's idea to use some wire supports to both hold the wings on and provide some structural stability. The only problem is that I put one of them in the wrong spot and had to cut it out to remove and replace it.

Skyhiker
I made it just in time.

Greg Baker
After an enormous amount of fiddling, I finally got the windows in place and Tintin, Snowy, and the medical kit seated. Now I can start to close it up. Thanks god.

Erik De Smet
Nice project again. A resin kit is always tricky and the tiny parts fragile, especially the u\c. Luckily this one will be flying. btw , Greg, do you mind making the propeller spinning in the opposite direction, so that it pushes itself in place ? I did it on some of my models, it is hardly visible . The main advantage is that you don't need to glue the propeller to the motor axle with ca, just a little bit of tacky paste inside the propeller tube will be enough.

bughunter
Greg is building an Omega resin bird 👍 I have some in my stash - in 1:48 as usual - but have not started one until now.

Greg Baker
You're right, Erik. I replaced almost the entire upper canopy framing with polystyrene and wire. I had to add some windows to this kit and wanted some consistency in the thickness of the frame. It was tricky to get everything glued in place, but I got it done more or less to my satisfaction. I'm hesitant to add the u/c elements because they seem rather fragile, but you're also right that it being in-flight will help a lot.

Greg Baker
I'm intrigued by the opposite spinning propellor idea. I can see where that might make things easier. Hmmmm...

Lode Schildermans
I'm in

Nicolas
Missed this one. Joining the fun.

Greg Baker
You haven't missed much... I had to redo much of the canopy... updated photos coming soon~

Lode Schildermans
I'll take a seat as well 🙂

Greg Baker
And... we're back. As I mentioned, the canopy basically fell apart while trying to install the windows, but it seems to be stable now. I also added a small tail wheel (as in the reference image) that I scavenged from the spares box. Next up, paint it pink and fix any issues that reveals. 🙂

Spanjaard
I will seat next to Lode 🙂

Cuajete
Great, Greg! 👍

gorby
Nice work on what looks like a challenging kit.

Moreno Baruffini
Wow, very nice work 👍🏻

Greg Baker
The first of my "back to school" photo album updates. This was a really challenging kit to build. I'm not sure how Uwe did such a great job on his version... The canopy/wing spar almost defeated me. The clear parts are a lot less clear than I would've liked, but at least you can tell who's flying the plane, right?

Cuajete
Great job for this hard kit, Greg. Good paint finish. Definitely much better with the wire crossbars and can see perfectly who is inside 👍
Congrats!

bughunter
You finished this kit to a nice looking miniature diorama 👍
The Omega resin kits seems to be not that easy. I have some in my stash - one day in future I will try one.

Greg Baker
Thanks guys! I can honestly say, the Omega resin kit left a lot to be desired. It might have gone together more easily if I hadn't carved out a larger cockpit area and added the cross bars. That really set me back a lot. Also, the surface in many areas (especially the wings) was not particularly clean. Defects in the mould made for odd blobs and scratches that needed to be sanded or filled to the best of my abilities.

Greg Baker
Just to show the propellor in action:

Youtube Video

Cuajete
Great, Greg! 👍

Robert Podkoński
Great job indeed, Greg!

Ian Doody
Next 1/72 Bandai Star Wars kit, B-Wing. Think I want this to be different to the movie one, so possibly Green or Blue Squadron, or something else, not sure. Just snapped most of it together, to get a clue about sub assemblies, and where the paints going. The Sullustian Pilot is teeny tiny, eeny weenie.

Gareth Lloyd
Nice 😎
Green squadron is a good one to go for, I've made one of those. The grey blue and light grey stripes front and back are good masking practice😊and gives plenty of weathering options.

Treehugger
I think maybe this is the special edition, with the alternative pilot figure.

Treehugger
Q: I've always wondered, how long is the B-Wing model in 1:72 scale?

Gareth Lloyd
@Treehugger, I'm guessing you mean from the top of the cockpit to the big cannons at the 'bottom'? Although it can fly in pretty much any orientation.
Quick measurement on My Bandai ones gives roughly 24cm (9.45 inch)

Ian Doody
B-Wing Cockpit and the Galaxies smallest Sullustan Pilot, Bien Numb. Looks like I'm going for Orange Squadron with this one. It's amazing he is painted at all, 1/72 really is too small for me now.

Ian Doody
That's it for today, I'm going in a totally different direction to the boxart version. Thinking Brown Two lol 😆 or a member of Orange Squadron. I'll see where I end up.

Finn
Looking good, will follow

Ian Doody
Not much done on this recently, as I've not been in the mood. A very long way still to go, just blocking in basic colours still. But, it does look like a B-Wing.

Gareth Lloyd
Looking for inspiration? This was mine : [img1] (still trying to push you towards a Green Squadron 😉 )

Ian Doody
For the moment, this project is now on hold, until inspiration hits me again. At a future point, I'll pick it back up and finish it. But for now I have to get back to my F1 kits.

Ian Doody
1/90ish Bandai Slayn & Korpil A/SF-01B B-Wing Heavy Assault Starfighter. End of day one. So far, so cool. New lighting, and brand new painting chair, seem to be working together. Really like the direction this one's going. "Orange 5" Rogue Squadron.

Jennifer Franklin
Following

Ian Doody
Cockpit almost done. Definitely liking this one, a lot more interesting than the movie version. This is one knackered B-Wing.

Ian Doody
That's it for another day. Fitted the sensor pods to the neck engine area. Looking nice so far.

Nathan Dempsey
Looking great 👍🏼

Freak
Incredible worn paint look! Can you share some of your process?

Ian Doody
@Freak it's just washes, lots of watered down washes, hand painted scratches, and chips, smudged hobby paint. mushed together.

Lost_Erik
Awesome! Great progress!

Skyhiker
Love this

Ian Doody
Engines done on the Bandai B-Wing. And making a start on the lower wing body. Trying to make it look like it's had a few parts replaced from other ships, and has seen a fair few battles. A veterans ship, kept going with whatever the crew chief can get her hands on.

Ian Doody
This is the last post for the next two weeks on the B, work will continue, and I'll finish it up after my Birthday, probably first week of March. Just blocking in colours and weathering with washes as I go. Then I'll go back over it with chips, and finally add decals and ID markings.

Jennifer Franklin
Happy Birthday

Your modeling work is looking good. Look forward to your return.

Lost_Erik
🙂 Happy Birthday!

CaptGPF
Happy birthday! Now get back to that B-Wing! 😜
Kidding aside, may you have many more years doing what you love.

Rui S
Great weathering 👍

Ian Doody
WIP, 1/72 Bandai B-Wing Heavy Assault Starfighter, painting it as a member of Rogue Squadron. Bored of creamy grey Star Wars stuff. Adding paint that I think makes it interesting to look at, so breaking up large areas with scuffs, scratches and mud splats, rust patches. This is all basic areas, I'll add the Squadron markings eventually.

Vincent
Very interesting paint choice!! Great weathering also!

Lost_Erik
👍 Loving your progress and paint / pallet choices!

Ian Doody
Rogue Squadron B-Wing Heavy Assault Starfighter. A bit more painting and weathering done today. Quite pleased how different it looks to the stock B. More to come, have the main lower wing area to do, then weapons, then Squadron ID markings.

Ian Doody
I'll be taking a look at this tomorrow ,time to finish it off.

Nicolas
Following

Robert Podkoński
Watching too.

Kees Borgers
Me too.

Mr D
Nice one 👍👍 Good job coming along 👌

Ian Doody
Made a start on the 1/32 Trumpeter F4F-4 Wildcat, I'm having my wings permanently folded, this is just all dry fitted so far, I'll add more detail later when the wing is added. No point cleaning up the inside part of the wing of ejection holes, as this will be hidden behind the wing. Think it looks ok so far.

Ian Doody
So today I've semi painted up the other sides wing root fold system. And started dry fitting the engine. Need to pick a scheme from the Techmod decals at some point, thinking of 1 or 4 so far.

Ian Doody
Ooh landing gear and engine support structure. Just needs a few touchups, thats it done for now, have to glue it all up straight away, doing it later would be a pain in the ass. Looks ok, I'm no expert on these things. Just for fun build in-between other stuff.

Ian Doody
I think, as an engine that'll do really, don't need anymore detail on it. Couldn't see it if it was there anyway. I'll paint the rear bank of cylinders, but that's probably it.

Ian Doody
That's all for today, making the most of what you get in the kit, only added bits of wire, no sense going mad with detailing parts you wont see. Prop tomorrow, finish the rear bank of Cylinders, and make a start on the cockpit. Looking nice so far, looks like an engine to me.

Ian Doody
Engine, exhaust manifold system and front bulkhead done. For what you can see, the kit parts are good enough. No point spending lots of money on a resin engine. Just some wire and a bit of paint.

Rui S
Looking special 👍 I'm in 😎

Guy Rump
Looking good and detailed build notes, following. 👍

Ian Doody
That's it for today, don't think I can handle seatbelts as well. So far so good, looks like a cockpit, when it's in the plane, you won't see anything. I tarted up the kit seat, as I couldn't stomach making the PE eduard one.

Rui S
hum, hum 😎 looking good 👍

Ian Doody
So I can do seat belts, but I hate doing seatbelts, not brilliant, but for all you'll see, it'll do me. My fear of PE is lessening, I'm getting a bit more confident each time, next the top straps. Then I can tackle the joining of the fuselage halves together, which is tricky on the 1/32 Trumpeter F4F-4 Wildcat, as a few parts need extra sanding to fit. Looks ok to me so far.

Ian Doody
Seatbelts done, that'll do. With my eyesight it'll look amazing from far away lol 😆 but for me, as a learning exercise, looks fine. I would wholeheartedly recommend HGW Laser seatbelts, they make it a lot easier.

Ian Doody
Tomorrow I'll make a start on the Empennage and getting everything to fit. I'm not using any of the PE hinges either. Then wings.

J35J
Great work and progress so far!👍🏻

Ian Doody
Back to the 1/32 Wildcat. Start of paint.

Ian Doody
Hmm, this is going to be interesting. As usual no idea what I'm doing, just riding by the seat of my pants. I'll try and block in all the colours then look into weathering. Who knows how this'll look.

Ian Doody
Well, it's blueish grey now, or greyish blue. Because I'm a cantankerous stubborn fool, I paint everything with brushes, Main colours blocked in, teeny tiny fiddly bits added, now I've just got to build some more layers up, start lightening and shading areas. It won't be brilliant, but it may look good on my shelf. Which is the main thing, due to lack of space, pretty much all the aircraft I'm going to build will have folded wings.

Mr D
Very nice, the wing internal colour looks spot on👌, l tried mixing this colour but struggled to get right tone.
Nice looking kit, what do you make of the Trumpeter kits??
Good luck with the next steps 👍👍

Ian Doody
Hello Mr D, so far I've only looked at early Trumpeter kits, panel lines are a bit too light for me, the early ones have gimmicks like working wing folds, and the PE hinges, but they build up quite well, and to me look like what it says on the box. I've got a lot more Trumpeter and Hobby Boss kits to build up in the future.

Ian Doody
As is my usual way, I have absolutely no idea what I'm doing, just going with the flow, it seems to want to be like this.
A very, very long way to go still, it'll be a lot lighter than it is now, and not so stark. I know, I shouldn't weather it until later, but i can't help it, it's a curse.

Mr D
It's a cracking looking model 👍👍
The weathering is looking good nice balance.
The internal metal parts ....the yellow/green..Did you mix or have the colour ready in a bottle

Ian Doody
Mr D, the green is just mixed up as and when I need it, it's just a caramel mixed with green paint.

John
Looking good, Ian!

Mr D
Thanks Ian, good to know...l tried mixing from yellow n green but didnt look right.
Cheers 👍👍

John
Mr D, try black and yellow. It sounds strange but it works. The more yellow, the more like yellow zinc chromate it looks. More black gives you the OD version.

Ian Doody
Right, well that's that for a while, going to be taking a break from this for a bit. It's going in the right direction, but it's turning into a long term project, I'll come back to it in a few months time with fresh eyes.

Milos C
Hi mate,
do you still offer this model M113 FItter?
Can you sand me some actual photos of your model - how it looks like - sprue, box, decals... It is old model.
And post costs to Czech rep. and/or to some box to Zittau (GER).
Thank you
milos.ciniburk@gmail.com

Steffen
Hello, tomorrow you will receive pictures and the price for shipping.
Regards, Steffen

Neil
Thanks Villiers de Vos

Treehugger
Btw, there are two tiny thingies at both end of the big wings. These are nav lights of sorts. Red on the left side, and blue on the right side, according to some paint chart I've seen recently.

Neil
Hi Treehugger ? kind of you to offer advice... Excellent build help indeed. Thanks for the tip ?

Neil
Thanks Petr 👍

Gary Victory
Looking good Neil.

Neil
Thanks very much Gary, kind of you to comment 🙂 👍

Neil
Thanks for commenting Flight Line Media 👍

James C
Looking good and following 👍

Neil
Cheers James 🙂

Neil
Thanks Roland 👍🙂

Jos Jansen
Oh wow...missed this one...following mate!

Andrew Horton
Wow! I look forward to seeing this build completed.

Mirko Römer
You can never have enough Viggens... 👍

Neil
Thanks Jos 👍 🙂 and Flight Line Media 👍

Neil
I agree Mirko! 💯👍

Konrad -
Awesome Neil!!

Neil
Hi Konrad 🙂 thanks very much 👍

Robert Podkoński
Viggen in yellow and blue!!! I love it! Watching with pleasure, Neil.

Neil
Excellent! Welcome aboard Robert 👍🙂

Neil
Hi all 🙂 I've finally got around to taking 'reveal' pictures for many of my previous build albums. I shall be updating each and including a few build notes in the description too - especially on the bits I messed up!

Here is my version of that 'Blu Petter' kit for the Airfix Saab Viggen completed in 2021. Excuses alert! It wasn't the best fitting kit, being an earlier Airfix effort.

Thanks to all who showed interest and liked, it's greatly appreciated 👍

Robert Podkoński
Looks perfect, Neil. Congrats!

Neil
Thanks Robert. you're too kind mate 🙂 👍

Christian
Hey Neil, really nice Viggen!

Neil
Cheers Christian! 😁

Jennifer Franklin
Very nice Neil, looks amazing.

James C
Congrats mate, that's a stunning finish 👍

Neil
Thanks Jennifer!

Spanjaard
very nice result in this old kit, love it.

Neil
Thanks James C 👍 and to those who've liked!

Neil
Thanks very much indeed for saying that Spanjaard, appreciate it 🙏🙂

Robin (WhiteGlint)
Wow! Great looking Viggen. Vibrant Blue and yellow

Neil
Thanks very much Robin! 🙂

gorby
WOW! Amazing result Neil.

Neil
Thanks very much Gorby. Much appreciated 👍

Gary Victory
Really nice finish Neil. That blue really pops..👍. Great work Sir.

Daniel
Quite an eye catcher, very nice work 👍

CaptGPF
Loved the coloring and restrained weathering. Very well done!

Neil
Hi Gary, Daniel and CaptGPF, thanks very much mates. Really appreciate you talented bunch commenting. I too love the kit colour scheme on this one and with hindsight; and an acceptance of some kit flaws, in my opinion it builds up into a pretty decent kit for an older Airfix one 👍 Thanks also to all those who've liked my efforts here too 🙂

Shar Dipree
Very nice viggen. Good work! 👍

Neil
Thanks very much Shar 🙂👍 and thanks to others for the recent likes also 👍

Jennifer Franklin
I love the blue, it's remarkable.

Neil
Thanks very much Jennifer 🙂

Rando
Majestic!

Neil
Thanks mate! 👍

Cuajete
Interesting... Following!

Gerald
Hello Welcome here 🙂