Notícias
Simon Nagorsnik
adicionou um novo álbum de fotos.
adicionou um novo álbum de fotos.
13 29 June, 18:00
Tom B.
From what I´ve seen that should be a great little kit... for a hopefully fun and non-problematic build 👍 Will definetly grab this kit myself in time!
From what I´ve seen that should be a great little kit... for a hopefully fun and non-problematic build 👍 Will definetly grab this kit myself in time!
1 July, 09:41
Simon Nagorsnik
Hey guys, you´re welcome for sure!
@Tom B. : Well, I wasn't entirely convinced of the kit, I have to say.
I have noted a rough summary in the album info if you are interested.
Hey guys, you´re welcome for sure!
@Tom B. : Well, I wasn't entirely convinced of the kit, I have to say.
I have noted a rough summary in the album info if you are interested.
1 July, 15:15
Tom B.
Honestly did not expect the shortcomings you listed from what I´ve seen of the parts yet, so thanks for the heads-up 👍
Honestly did not expect the shortcomings you listed from what I´ve seen of the parts yet, so thanks for the heads-up 👍
1 July, 20:09
QQWAGG
quer este item
quer este item
British dispatch rider Taking carrier pigeons to front line
Copper State Models (CSM) 1:35
F35-059 2024 Produto novo 6 July, 19:20
QQWAGG
quer este item
quer este item
British dispatch rider With a basket of pigeons
Copper State Models (CSM) 1:35
F35-060 2024 Produto novo 6 July, 19:20
Todd Blakeslee
possui este item
possui este item
Kevin Harvick's
#29 Goodwrench Service Plus 2001 Chevy Monte Carlo Revell 1:24
85-2372 2001 Novos decalques 6 July, 19:14
Thomas Ehrensperger
quer este item
quer este item
F.F.G. Berlin B9 German Experimental Plane for Test Pilot in Lying Position
Kora Models 1:48
4809 200x Mudança ??? 6 July, 19:07
Tom B.
adicionou um novo álbum de fotos.
adicionou um novo álbum de fotos.
10 imagens
"Ditched in Normandy" - 15cm Panzerwerfer + Humber Scout Car1:72
Finished!
Projeto: Ditched in the Normandy
18 24 June, 19:22
Tom B.
Heyo all! I have not really posted anything about this particular project yet, even though is has been holding me up for quite a bit of time now...
As modellers, our hobby naturally includes a lot of problem-solving and some challenges and maybe I should not be complaining, but it felt like this particular project trew a bunch of sticks and stones in my path:
Firstly, the resin Humber Scout Car was abit of a challenge with all the sanding and cutting that comes with these types of kit... apparently taking the place of the instructions, which I did not get any of. With a bit of research however, it was overall ok to build.
Secondly, the Roden Panzerwerfer has rubber tracks which I knew were too short beforehand. Thus I first bought a 3D printed replacement running-gear from FC Modeltrend. That piece however turned out to be an example of how not to do 3D-printed products: it sat on the plate without any angle and was a single piecewith two tracks, the suspension and some chassis-parts... how does one support such a print? Apparently not correctly, as the supports along the side-details of the wheels and suspension parts were partially "molten" into the details which in the end prevented me from using this piece. If you have a micro-drill, calm hands and a lot of time, one could "carve out" the supports and reinstate the details, I suppose... For me, switching to a Modelltrans-set (one piece running gear for each side) was the order of the day. It is not perfectlycast either, but after some adjustment, I made it fit the Roden kit. Using the PE-set and doing the interior took a lot of time as well, but that was largely fine.
As said, maybe I am complaining too much and in that case do take these notes as a simple report on the difficulties experienced so far in this project... rant is over 👍
Heyo all! I have not really posted anything about this particular project yet, even though is has been holding me up for quite a bit of time now...
As modellers, our hobby naturally includes a lot of problem-solving and some challenges and maybe I should not be complaining, but it felt like this particular project trew a bunch of sticks and stones in my path:
Firstly, the resin Humber Scout Car was abit of a challenge with all the sanding and cutting that comes with these types of kit... apparently taking the place of the instructions, which I did not get any of. With a bit of research however, it was overall ok to build.
Secondly, the Roden Panzerwerfer has rubber tracks which I knew were too short beforehand. Thus I first bought a 3D printed replacement running-gear from FC Modeltrend. That piece however turned out to be an example of how not to do 3D-printed products: it sat on the plate without any angle and was a single piecewith two tracks, the suspension and some chassis-parts... how does one support such a print? Apparently not correctly, as the supports along the side-details of the wheels and suspension parts were partially "molten" into the details which in the end prevented me from using this piece. If you have a micro-drill, calm hands and a lot of time, one could "carve out" the supports and reinstate the details, I suppose... For me, switching to a Modelltrans-set (one piece running gear for each side) was the order of the day. It is not perfectlycast either, but after some adjustment, I made it fit the Roden kit. Using the PE-set and doing the interior took a lot of time as well, but that was largely fine.
As said, maybe I am complaining too much and in that case do take these notes as a simple report on the difficulties experienced so far in this project... rant is over 👍
24 June, 19:41
Alec K
Looks great so far! I certainly appreciate your report as it highlights challenges one can encounter: so rant away 🙂 👍
Looks great so far! I certainly appreciate your report as it highlights challenges one can encounter: so rant away 🙂 👍
25 June, 13:37
Tom B.
Appreciate your interest mates 👍 maybe I´m able to get the groundwork ready to paint with some additional scatter and some static grass
Appreciate your interest mates 👍 maybe I´m able to get the groundwork ready to paint with some additional scatter and some static grass
25 June, 14:15
/pt/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=pt
35
35
/pt/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo