Stearman PT-13, Revell 1/72
![Album image #1 Album image #1](/albums/img/3/1/7/912317-72216-49-720.jpg)
![Album image #2 Album image #2](/albums/img/2/9/9/871299-72216-44-720.jpg)
Some rework required to fit the Yahu instrument panel.
![Album image #3 Album image #3](/albums/img/3/0/2/871302-72216-38-720.jpg)
![Album image #4 Album image #4](/albums/img/3/0/0/871300-72216-50-720.jpg)
![Album image #5 Album image #5](/albums/img/3/0/3/871303-72216-34-720.jpg)
![Album image #6 Album image #6](/albums/img/3/0/1/871301-72216-22-720.jpg)
![Album image #7 Album image #7](/albums/img/3/0/4/871304-72216-31-720.jpg)
Interior almost complete, with DDT tank
![Album image #8 Album image #8](/albums/img/0/8/7/872087-72216-51-720.jpg)
When I ordered the Dekno models 1/72 Lycoming I didn't expect to be so good.
![Album image #9 Album image #9](/albums/img/0/9/0/872090-72216-22-720.jpg)
![Album image #10 Album image #10](/albums/img/0/8/8/872088-72216-73-720.jpg)
Unfortunatelly Dekno does not include the exhaust collector. I used the kit part mostly to be sure for the symmetry of the 9 exhaust pipes.
![Album image #11 Album image #11](/albums/img/0/8/9/872089-72216-40-720.jpg)
![Album image #12 Album image #12](/albums/img/0/9/1/872091-72216-52-720.jpg)
![Album image #13 Album image #13](/albums/img/0/9/2/872092-72216-59-720.jpg)
![Album image #14 Album image #14](/albums/img/0/9/5/872095-72216-68-720.jpg)
Collector installed. A triangular part arount the prop hub serves as the base for the collector, same as in real engine. Ready to glue the pipes
![Album image #15 Album image #15](/albums/img/0/9/3/872093-72216-44-720.jpg)
Pipes glued to collector. Thick cyano will glue the other end to cylinder head and act as a "filler".
![Album image #16 Album image #16](/albums/img/0/9/4/872094-72216-47-720.jpg)
The small oil pipes on cylinder heads made from a piece of copper wire. After the cyano glue was set the parts of wire between cylinders were removed.
![Album image #17 Album image #17](/albums/img/0/9/6/872096-72216-61-720.jpg)
The main exhaust made from 2mm styrene rod heated to bend as required. Remain to install the small oil tubes between cylinders at the rear of the cyl heads.
![Album image #18 Album image #18](/albums/img/9/1/5/895915-72216-19-720.jpg)
ResKit resin P-51 wheels were used as a substitute for the kit's very mediocre parts.
Rim covers were made from plasticard and a new tail gear from brass rod.
Rim covers were made from plasticard and a new tail gear from brass rod.
![Album image #19 Album image #19](/albums/img/9/1/4/895914-72216-91-720.jpg)
Basic painting with MrColor C329 and rigging started. Cabane struts replaced with aeroclub airfoil strut, kit parts are too short and thick.
![Album image #20 Album image #20](/albums/img/9/1/7/895917-72216-47-720.jpg)
Revell's 1/48 instructions used as a rigging guide
![Album image #21 Album image #21](/albums/img/9/1/6/895916-72216-43-720.jpg)
Rigging complete. After 24 hours (to be sure cyano has set) I will trim and sand the rigging holes as required.
![Album image #22 Album image #22](/albums/img/3/1/0/912310-72216-49-720.jpg)
Engine painted and installed
![Album image #23 Album image #23](/albums/img/3/1/1/912311-72216-70-720.jpg)
"Thermal aerosol spraying" exhaust built from styrene rod.
![Album image #24 Album image #24](/albums/img/3/1/4/912314-72216-83-720.jpg)
Exhaust installed
![Album image #25 Album image #25](/albums/img/3/1/2/912312-72216-44-720.jpg)
Exhaust collector installed on engine.
![Album image #26 Album image #26](/albums/img/3/1/3/912313-72216-50-720.jpg)
DDT ram air driven pump built from scratch.
![Album image #27 Album image #27](/albums/img/3/1/5/912315-72216-60-720.jpg)
Pump installed
![Album image #28 Album image #28](/albums/img/3/1/6/912316-72216-40-720.jpg)
Pump installed
![Album image #29 Album image #29](/albums/img/3/1/8/912318-72216-89-720.jpg)
All decals applied. My design, custom printed by LM decals
![Album image #30 Album image #30](/albums/img/5/8/0/913580-72216-49-720.jpg)
![Album image #31 Album image #31](/albums/img/5/7/9/913579-72216-39-720.jpg)
![Album image #32 Album image #32](/albums/img/3/6/7/1671367-72216-12-720.jpg)
![Album image #33 Album image #33](/albums/img/3/6/4/1671364-72216-16-720.jpg)
![Album image #34 Album image #34](/albums/img/3/6/9/1671369-72216-97-720.jpg)
![Album image #35 Album image #35](/albums/img/3/6/5/1671365-72216-19-720.jpg)
![Album image #36 Album image #36](/albums/img/3/6/8/1671368-72216-22-720.jpg)
![Album image #37 Album image #37](/albums/img/3/6/6/1671366-72216-28-720.jpg)
![Album image #38 Album image #38](/albums/img/3/7/0/1671370-72216-72-720.jpg)
![Album image #39 Album image #39](/albums/img/3/7/2/1671372-72216-45-720.jpg)
![Album image #40 Album image #40](/albums/img/3/7/1/1671371-72216-11-720.jpg)
![Album image #41 Album image #41](/albums/img/0/2/9/1077029-72216-37-720.jpg)
Comentários
46 4 November 2020, 22:21
![](/profiles/img/13136-468-s.jpg)
Great cockpit detail, Elias! Looking forward to watching your progress!
5 November 2020, 18:40
![](/profiles/img/72216-801-s.jpg)
Thanks for your encouragement 🙂
Next comes the engine, 3D printed by Dekno models. No need to comment the level of detail compared to the stock piece. Some extra work required for the exhaust collector ring and pipe. I will suggest dekno to include this part in the future.
7 November 2020, 00:12
![](/profiles/img/44957-709-s.jpg)
Great progress! Now, with the rigging nearly done, bring on the TAS stuff😉
18 December 2020, 19:11
![](/profiles/img/13136-468-s.jpg)
Tires look great, and Excellent work on the rigging, Elias! Much respect for doing double wires in 1/72!
19 December 2020, 18:48
![](/profiles/img/44957-709-s.jpg)
The scratch-built spraying equipment turned out great - the air-driven pump, in particular, is a little gem! 👍
11 January 2021, 16:09
![](/profiles/img/72216-801-s.jpg)
I think this is enough with this old kit 🙂
That was a very special project requiring more time for research than for building. A lot of fun! 🙂
25 January 2021, 23:34
![](/profiles/img/44957-709-s.jpg)
Ok, κάτι κατάφερες! 😛 No, seriously, great work on an obscure (up to now😉😢 subject! Two thumbs up 👍 👍
26 January 2021, 00:07
![](/profiles/img/103381-754-s.jpg)
Thank you; I will look into it; always wanted to try to do some rigging; it really adds an extra element to it
24 September 2021, 21:17
![](/profiles/img/72216-801-s.jpg)
Ευχαριστω!
Και το ΡΤ-17: Stearman PT-17 Kaydet Revell 1/48 | Album by EliasK (1:48)
29 September 2021, 16:05
Album info
Stearman PT-13, Revell 1/72. Malaria control duster, Greece 1948.