Kawasaki C-1
![Album image #1 Album image #1](/albums/img/7/4/2/1124742-47247-73-720.jpg)
A very expensive and time-consuming kit to produce, hahaha!
![Album image #2 Album image #2](/albums/img/9/7/9/1124979-47247-12-720.jpg)
The landing gear must be made by yourself, as the kit is basically made in flight.
![Album image #3 Album image #3](/albums/img/9/7/5/1124975-47247-70-720.jpg)
The front wheels, in particular, require a sculptural skill.
I need to get our hands on a chisel...
I need to get our hands on a chisel...
![Album image #4 Album image #4](/albums/img/9/7/8/1124978-47247-50-720.jpg)
The starboard side has been cut open.
The C-1's landing gear is not pulled up vertically like the C-130's, so it takes up a lot of space.
The C-1's landing gear is not pulled up vertically like the C-130's, so it takes up a lot of space.
![Album image #5 Album image #5](/albums/img/9/8/1/1124981-47247-26-720.jpg)
The thickness of the wings is not uniform!
I'm in trouble...
I'm in trouble...
![Album image #6 Album image #6](/albums/img/9/8/0/1124980-47247-35-720.jpg)
In addition, the vortex generator is missing due to a molding defect.
I'll have to chop up some plastic plates.
I'll have to chop up some plastic plates.
![Album image #7 Album image #7](/albums/img/9/7/6/1124976-47247-47-720.jpg)
I worked hard and installed 2/3 of the landing gear.
However, after I took the photos I realised that the starboard main gear was installed in the wrong position, so I corrected it.
However, after I took the photos I realised that the starboard main gear was installed in the wrong position, so I corrected it.
![Album image #8 Album image #8](/albums/img/6/2/5/1127625-47247-57-720.jpg)
It is roughly this size.
It is smaller than the C-130 and about the same size as the An-72.
It is smaller than the C-130 and about the same size as the An-72.
![Album image #9 Album image #9](/albums/img/6/8/2/1125682-47247-12-720.jpg)
The gear bay on the port side has also been opened.
The resin is thicker than on the starboard side...
The resin is thicker than on the starboard side...
![Album image #10 Album image #10](/albums/img/6/8/1/1125681-47247-34-720.jpg)
Make the bulkheads as appropriate.
![Album image #11 Album image #11](/albums/img/6/8/0/1125680-47247-89-720.jpg)
With this gap it's impossible to get in-flight pressurisation...
![Album image #12 Album image #12](/albums/img/6/7/9/1125679-47247-78-720.jpg)
There is a Japanese proverb that says, "When the impossible is done, the reasonable is pulled in."
![Album image #13 Album image #13](/albums/img/2/7/4/1127274-47247-31-720.jpg)
The gaps in the main wings are carefully filled.
This is because the work of correcting the thickness of the wing is continuously subjected to strong force...
This is because the work of correcting the thickness of the wing is continuously subjected to strong force...
![Album image #14 Album image #14](/albums/img/6/7/6/1125676-47247-69-720.jpg)
Create the APU system.
This kit really only shows the general shape of the C-1, so it is up to me to reproduce the details.
This kit really only shows the general shape of the C-1, so it is up to me to reproduce the details.
![Album image #15 Album image #15](/albums/img/6/7/7/1125677-47247-70-720.jpg)
The whole picture is now clear.
From a distance it looks good, but up close it's quite rickety.
Fixing this is the goal now!
From a distance it looks good, but up close it's quite rickety.
Fixing this is the goal now!
![Album image #16 Album image #16](/albums/img/2/7/6/1127276-47247-50-720.jpg)
This is terrible...
![Album image #17 Album image #17](/albums/img/2/7/7/1127277-47247-95-720.jpg)
That's about it!
![Album image #18 Album image #18](/albums/img/6/7/8/1125678-47247-96-720.jpg)
If there is a gap, the fuselage can break with the slightest impact.
Fill the gaps with high density epoxy putty and go to bed.
Fill the gaps with high density epoxy putty and go to bed.
![Album image #19 Album image #19](/albums/img/2/7/1/1127271-47247-21-720.jpg)
Even the JT8D engine is jamming.
![Album image #20 Album image #20](/albums/img/2/6/9/1127269-47247-65-720.jpg)
The JT8D will now have normal thrust.
![Album image #21 Album image #21](/albums/img/2/7/2/1127272-47247-92-720.jpg)
Not only the nozzle but also the body is rattling...
![Album image #22 Album image #22](/albums/img/2/7/0/1127270-47247-33-720.jpg)
I sanded the windows and stuff.
![Album image #23 Album image #23](/albums/img/2/6/8/1127268-47247-26-720.jpg)
Most of the parts have been glued together.
I would like to paint the parts in separate pieces and then assemble them, but the gaps are so big that I can't do that.
I would like to paint the parts in separate pieces and then assemble them, but the gaps are so big that I can't do that.
![Album image #24 Album image #24](/albums/img/2/6/7/1127267-47247-62-720.jpg)
The gaps were filled with epoxy putty and filed.
I'm tempted to paint the surfacer here, but there are still a few parts that I haven't fitted yet.
I'm tempted to paint the surfacer here, but there are still a few parts that I haven't fitted yet.
![Album image #25 Album image #25](/albums/img/2/6/5/1127265-47247-31-720.jpg)
That's right, 30 vortex generators per side, 60 on each side!
![Album image #26 Album image #26](/albums/img/2/6/4/1127264-47247-65-720.jpg)
I did my best to plant them.
![Album image #27 Album image #27](/albums/img/2/6/6/1127266-47247-78-720.jpg)
I took a commemorative photo with Hasegawa's 1/200 C-1, which I have been using as a replacement for the instruction manual since my work has progressed considerably.
![Album image #28 Album image #28](/albums/img/8/8/8/1127888-47247-42-720.jpg)
At last we have painted the surfacer!
I don't like to use it unless it's an injection kit with a strong moulding colour or resin kit , as I always have trouble adjusting the consistency.
I don't like to use it unless it's an injection kit with a strong moulding colour or resin kit , as I always have trouble adjusting the consistency.
![Album image #29 Album image #29](/albums/img/8/8/6/1127886-47247-75-720.jpg)
Walkway painted. (by Mr. Colour No. 317)
![Album image #30 Album image #30](/albums/img/8/8/7/1127887-47247-81-720.jpg)
I painted the first colour of the camouflage.
This tricolour camouflage needs to be considered carefully because the colour of the sand yellow varies from time to time and fades rather severely with sun exposure.
This tricolour camouflage needs to be considered carefully because the colour of the sand yellow varies from time to time and fades rather severely with sun exposure.
![Album image #31 Album image #31](/albums/img/2/3/1/1128231-47247-52-720.jpg)
I painted the second colour of the camouflage.
I don't know... we're painting camouflage by atmosphere...
I don't know... we're painting camouflage by atmosphere...
![Album image #32 Album image #32](/albums/img/2/3/2/1128232-47247-35-720.jpg)
I painted the third colour of the camouflage.
![Album image #33 Album image #33](/albums/img/2/3/3/1128233-47247-77-720.jpg)
All masking has been removed.
![Album image #34 Album image #34](/albums/img/2/3/0/1128230-47247-99-720.jpg)
Painting of the gear bay and engine nozzle.
I secretly painted the underside too!
I secretly painted the underside too!
![Album image #35 Album image #35](/albums/img/2/2/7/1128227-47247-15-720.jpg)
Masking is a pain in the ass.
![Album image #36 Album image #36](/albums/img/2/2/9/1128229-47247-36-720.jpg)
The nose has turned black ˙ᴥ˙
I wonder if it would make a difference if I sprayed it with a matte spray...
I wonder if it would make a difference if I sprayed it with a matte spray...
![Album image #37 Album image #37](/albums/img/0/1/6/1129016-47247-93-720.jpg)
I sprayed the surface with clear to prepare it for the decals.
This should reduce the silbering phenomenon somewhat.
This should reduce the silbering phenomenon somewhat.
![Album image #38 Album image #38](/albums/img/0/1/5/1129015-47247-62-720.jpg)
And here I have yet another problem!
The emblem of the 2nd Transport Air Wing has a section bordered in white.
This decal has a white layer as a base, but the border is transparent!
Why? !
The emblem of the 2nd Transport Air Wing has a section bordered in white.
This decal has a white layer as a base, but the border is transparent!
Why? !
![Album image #39 Album image #39](/albums/img/0/1/4/1129014-47247-61-720.jpg)
I had no choice but to make a stencil and paint it white.
![Album image #40 Album image #40](/albums/img/0/1/3/1129013-47247-64-720.jpg)
The result was not much spillage.
![Album image #41 Album image #41](/albums/img/0/1/2/1129012-47247-30-720.jpg)
I did it!
I got the result I was hoping for.
I got the result I was hoping for.
![Album image #42 Album image #42](/albums/img/0/1/1/1129011-47247-70-720.jpg)
All the decals were applied and the glossy spray painted.
Now it's ready for weathering!
Now it's ready for weathering!
![Album image #43 Album image #43](/albums/img/0/1/0/1129010-47247-53-720.jpg)
Mission complete!
![Album image #44 Album image #44](/albums/img/0/0/9/1129009-47247-85-720.jpg)
![Album image #45 Album image #45](/albums/img/0/0/7/1129007-47247-92-720.jpg)
![Album image #46 Album image #46](/albums/img/0/0/6/1129006-47247-82-720.jpg)
![Album image #47 Album image #47](/albums/img/0/0/8/1129008-47247-62-720.jpg)
Comentários
24 10 December 2021, 11:57
![](/profiles/img/102691-453-s.png)
Nice project but looks like a lot of work.....🤔
I'm looking forward to seeing what you make of it- good luck!
10 December 2021, 19:29
![](/profiles/img/82560-921-s.jpg)
Good lord, this is a Herculean effort! The thickness of those fuselage halves! Very impressive work so far
14 December 2021, 17:53
![](/profiles/img/102691-453-s.png)
really nice camo pattern!
good masking work
still follow your project 😃
16 December 2021, 21:40
![](/profiles/img/14105-839-s.jpg)
You have certainly beaten that kit into a very acceptable shape. It is looking great
16 December 2021, 21:46
![](/profiles/img/57594-145-s.jpg)
What a cool camo! I like it a lot! And what a huge job with this resin kit, amazing effort.
16 December 2021, 22:07
![](/profiles/img/27826-126-s.jpg)
Fantastic job for this kit. I hope someday any plastic's brand release ones in this scale.
Congrats!
17 December 2021, 19:02