Work In Progress(Plarz/Italeri)

1
January 17, 2023
Start with front bay.
2
January 22, 2023
jet nozzle sanded to look thinner.
3
January 22, 2023
These places are difficult to sand.
4
January 22, 2023
mmm.
5
January 22, 2023
need to loosen contact here
6
January 22, 2023
7
January 22, 2023
8
January 22, 2023
9
January 22, 2023
10
January 22, 2023
11
January 22, 2023
12
February 6, 2023
Set left engine cover ~0.5mm back to match mild lines.
13
February 6, 2023
Fan blades also need repositioning.
14
February 8, 2023
utilized power of boiled water to bend plastic plate.
15
February 8, 2023
utilized power of math and CA glue.
16
February 8, 2023
fan blade position adjusted to 14.7mm behind intake lip. need some putty and sanding.
17
February 14, 2023
now look allowable
18
February 14, 2023
fill the gaps
19
February 24, 2023
This portion is much simpler than academy :⁠-⁠)
20
February 24, 2023
cut AN/ALR-46 antenna, which is replaced by much smaller AN/ALR-69
21
March 20, 2023
removed a hydraulic link and added bases for harnesses.
22
March 28, 2023
sand front of body and upper wing. Wing tip.antenna attatched.
23
March 28, 2023
platz(eduardo) etching applied.
24
March 28, 2023
butt
25
April 11, 2023
Eduardo print etching appears not to be resistant to water. Control panel wobbled.
26
April 12, 2023
I tried decal softer for remedy, but result is worse.
27
April 12, 2023
repeated sanding and filling make engine pod surface fine.
28
April 12, 2023
I'll attatch square patch for access hatches.
29
April 23, 2023
Put etching HUD parts on cockpit.
30
April 23, 2023
Attatch wire mesh to the holes.
31
May 20, 2023
Peel off water-damaged coloured layer. すっきりしたぜ(l'll feel a whole lot better).
32
May 20, 2023
Brush xf-19 for decals to come.
33
May 20, 2023
re-revet
34
May 20, 2023
35
June 11, 2023
Recovered with decal from Academy kit. I engraved HUD mount area to avoid interfere with canopy
36
August 1, 2023
repair in progress for cracked intakes.
37
August 15, 2023
thanks to magnet in front wheel, the plane stand still withougt weigtht in nose.
38
August 15, 2023
Secure joint strength and cure injection failure.
39
August 21, 2023
add a little detail to the tail.
40
August 21, 2023
I am the Warlus.
41
September 3, 2023
42
September 3, 2023
Spray tamiya lp54 dark iron over silver-green.
43
September 3, 2023
masking ready for gunship grey area.
44
September 3, 2023
creos c338 to enhance contrast.
45
September 3, 2023
46
October 28, 2023
nearing completion.
47
October 28, 2023
48
October 28, 2023
I seem to lost HUD parts.
49
October 28, 2023
50
October 28, 2023
51
October 29, 2023
Managed to join the squadron badge I accidentally cut in two pieces.
52
October 29, 2023
snakehead done.
53
October 29, 2023
54
January 8, 2024
almost complete, pilot and pitot to be done

Comentários

25 17 January 2023, 15:52

Arthur Kirkland
完成するのが今からとても楽しみです！

22 January 2023, 14:35

Marek Valko
Size of the rivets on engine covers looks to much big. When I watched the review I was impresed but now when I am looking on this I am confused if I should to buy it.

23 January 2023, 07:08