Новостная лента

gorby
Looks like a very interesting build.

Doubtingmango
Watching

Ingmar Stöhr
Nice progress so far! Overall nice paintjob, but maybe try to use a little less paint on the railings. I see a lot of small paint balls forming there.

Guy Rump
Great job so far, following. 👍

Miguel Vaquero
Following!

Chrisswe
Thanks for your interest and comments. I did something wrong with the primer when painting the railings which caused the paint balls. Also I'm not great at working with PE yet and the glue residue is often visible even if try to paint over it. All in all I still think I'm making some improvements compared to my last build. Rigging will be my greatest challenge for this build.

Ingmar Stöhr
Ah, ok! Well yes, your glue is visible here an there, but otherwise I find your application of PE is not bad at all! What works for me with railings is to hold them in place with one hand (and tweezers) and with the other hand apply a tiny amount of very thin super glue from a piece of thin copper wire fixed to a toothpick as handle. This will instantly wick into the gap and also instantly fix the railing in place. After that I paint over the seam with the appropriate colour and mostly end up with very nice glue joints.

Chrisswe
That is probably the correct way to do it Ingmar. I find it difficult to only use the thin super glue as it has zero adhesive effect until it bonds. I use super glue gel to fix one end of the railing and then use your method for the rest.

Chrisswe
I'm testing a grey-brown panel liner instead of the black one I used for all of my last ship. It looks good closeup but might be to subtle when you look at the whole ship. Is it a bad idea to use anything else than black panel liner even on lighter colours when doing 1:350 scale?

Ingmar Stöhr
Actually super glue should set / cure / stick faster the thinner it is. A gel does lengthen the setting time. I start at one side, place the railing, put a tiny bit of thin super glue at the joint and it will typically set withing 2-3 seconds. Then I move a bit further down, align the PE, put glue there and so on. What also increases the setting time is a larger gap. If the gap ist very small and the glue very thin it will usually literally set instantly.

I like my wash with a lot of contrast. On my modern US Navy builds (kind of a medium gray) I will use blue-black panel line wash from AMIG. On a lighter gray, as with the superstructure on DKM units, that might be a bit to much contrast though.

Spanjaard
nice collection. is the decoration done with decals or painted? i am mostly talking about the very dark with light blue on the sides, and the golden decoration of the blue/purple

Jurgen Verhelst
On both cars are decals. The Skull on the Van is hand-painted.

Spanjaard
golden declal are an impresive work of decalling. really nicely done.
i am sorry, but I not see the skull in the van, maybe in the roof? i see something there, but the picture only shows the borders

Jurgen Verhelst
Indeed, Skull is on the Roof. I'll put a new picture.

Spanjaard
nice, thanks

Bob Hall
Sweet Rides ! Really Love the Blue on the 64 Mustang !

Alexander Grivonev
Great cars Jurgen!

Tom ...
Absolutely wonderful. I hope one day can have such a great collection. That's a lot of amazing work. Bravo!

Chris Greathouse
Awesome collection! I love the sparkly blue paint on #35 and your truck and trailer with cars, pic #42, is epic..

Thomas K.
Nice cars 👍

Dominik Weitzer
nice colection - so many different colors.
specially the bug (pic 22) and the yellow testarossa- beautiful! And the 328...love that.

Martin Oostrom
What I like most, is to see the evolution of your skills. Each new build shows you're getting better and better. Very nice 👍

Dominik Weitzer
nice update! The color from that lightblue Porsche 944 turbo looks like mine! Thats funny...

Villiers de Vos
A nice line-up.

George Williams
Such a varied collection it's hard to pick a favourite, but the Ford Escorts caught my eye.

Treehugger
Any relation to the movie Where Eagles Dare? 🙂

Steve
I think this is so cool!

Villiers de Vos
A very interesting subject.

Mr James
Looking forward to seeing this

Tim
Great film

Robert Podkoński
Taking a seat, of course!

bughunter
Welcome Robert! Which one you want to take, the yellow or a green one? 😉

Please do not miss the project description, for the _VERY_ important reason for this project!

Robert Podkoński
👍 A green one, please 🙂

Marcel Klemmer
Hi Frank, I am in and do not need a seat. 😉

Ludvík Kružík
I'll sit down too. If I'm not mistaken, one green seat is still open. 😉

Spanjaard
I am certainly in

Martin Oostrom
Green two for me

David H
Be rude not to join in. 👍🏻

gorby
I'll join the audience as well. 🙂

bughunter
Hello my friends! A warm welcome to each and every one of you!

Working on the parts of this kit can be considered bodily harm! The bright yellow hurts your eyes and you can't see any details or damaged areas that need work. I would have preferred a more common gray!

Michael Kohl
Moin Frank. Nimmst mich mit?

bughunter
Aber sicher doch, wenn Du eine wilde Fahrt aushälst 😉

Kenneth
Hallo Frank, the set with lap belts only could be intended for the US Navy variant of the Stearman, the N2S. Until US entry in WW2, US Navy aircraft mostly did not have shoulder belts. I read this in a review of a 1/32 Vought Kingfisher while looking for seatbelts and wondering about the same thing for my 1/32 Revell/ICM N2S Stearman kit.

Juergen Klinglhuber
Schau ich mir auch an,...

bughunter
Welcome! Thanks Kenneth! That makes sense, as the kit offers also a yellow Navy plane with red stripes. Luckily my wife want it blue-yellow. All the pictures I found shows also shoulder belts, but that was mostly still flying machines and I guess the shoulder belts was added later.
I had already downloaded the ICM manual as an additional reference and looked at reviews because of an oddity on the upper wing. More on this later.

bughunter
Because I was still in soldering mode after the seats, I immediately turned my attention to the tank on the upper wing. I like the look of the metal fuel tank now.

Robert Podkoński
Perhaps you will find my photos useful for your build:
Hangar 10 | Album by podkon

bughunter
Yes, definitely 👍 Thanks!

bughunter
Found a nice page: stearman-aero.com/

bughunter
The wing is yellow again, but now the look is better!
I used here MRP-142 Orange Yellow. If someone remembers my Piper: the yellow was "Dark Chrome Yellow" also from MRP. Even this one here called "Orange Yellow" it looks more yellow compared to the Piper.

Ben M
👀

Alec K
I was just wondering where the heck is Bughunter, and here he is! Lovely progress and topic, following of course 👍

bughunter
Welcome Ben and Alec!
The lower wing is now also painted yellow. I only not sure about the blue. I want to go with the darker later blue, tried AK Pure Blue, but I will also try others.

Jakub Fiala
Nice work on this interesting type of aircraft so far 👍 Following for sure!

Ben M
Love these old trainers. They used to show up at airshows a lot when I was a kid.

Greg Baker
Sign me up!

Zbynek Honzik
A joy and pleasure to follow such a project! 👍

Christoph Kunz
Ui, da habe ich den Start ja irgendwie verpennt. 🙁
Aber jetzt bin ich dabei.

Kenneth
Noch was, je nach dem, was das Vorbild ist: Part 71 in Point 4 of the instructions is in my opinion not correct for a WW2-era Stearman. Such a box typically houses a radio, intercom, transponder etc. on modern, restored examples

David Taylor
Watching.

bughunter
In the spirit of "Piano man": the regular crowd shuffled in ...
Welcome!
Oh, can someone wake up Kyle? 😉

Juergen Klinglhuber
Kyle! - come on, you will miss a good portion of the show and have to put the stool again in the back... 😉 Just kidding. It is never to late for a bughunter-show

bughunter
Kenneth, thanks for the hint! Interestingly the Eduard manual of the PE set here on SM told me to remove the mount points for this part 71. After that hint I checked some pictures of original machines and found the modern equipment. So thanks for the confirmation! After my PE set arrived I found out the remove of that mount points is missing in my paper version! Luckily I have checked the corrected online version first.

I would like to build a original equipped plane, but this is somehow limited. I have only the kit decals for a US Army plane "136" dated 1941. There is no serial number mentioned. I have not found photos of that plane yet. So I will build it according the information I have, with "educated guesses" on some points. Later more.

bughunter
I made the instrument panels. May be you know the Eduard sandwich method of multiple PE parts? Here we have a special thing!

Kenneth
Fuselage innner side colours are also totally wrong in the instructions (overall aluminium). See flugzeugforum.de/thr...103126/post-3062086 where I posted some thoughts about this.

The „thick" plate on the instrument panel which you chose is correct for the period, it's a padding saving an unfortunate student pilot's face when smashing it against the instrument panel…

bughunter
Kenneth, thank you very much for your great support 👍 Highly appreciated!
Now I understand, why the bolts of the instruments are hidden by this padding.
According to your picture I painted the fuselage halves bright linen and added the read brown tensioning varnish. It will not be very visible after closing the halves.

The inner structure is not in scale: much too thick! As it will be not very visible later I do not go the extra mile to replace the structure by brass wires!
Did someone say Jehovah? 😎

bughunter
The seat belts (what a fiddly job), the seats and the cockpit as a whole are finished. What beautiful interior!

Have I forgotten something, or can the fuselage halves be glued?

Ben M
Pancakes! (IYKYK)

gorby
Lovely work on the cockpit Bugs. 🙂

Kenneth
Looks perfect 👍 I was wondering whether there shouldn't be a fuel cock (the red lever on the lower left side in the front cockpit) in the rear cockpit as well, but found quite a few photos were this indeed not the case (but also some with one).

And while the ICM fuselage structure is indeed very delicate, it stops short of the rear cockpit!

bughunter
Thank you mates!
Beside the thick structure it is a nice kit (and Eduard PE set) with great fit. Sometimes even with the famous Tamiya click 🙂

@Ben Pancakes?! You say if you know you know, but I do not know 🙁
If you mean the upholstery of the seats - I think that this task was taken over by the parachutes.

bughunter
The kit includes a clear lamp to be installed on the back of the fuselage for Navy and Army. I have not found a reference photo.
Is this perhaps an anti-collision light on modern aircraft? Add it or leave it out?

Kenneth
That fuselage lamp (probably a modern strobe light) does not appear in the manual available on the Stearman Aero site (p. 105)… from which I've also just learned that the red lever I mentioned earlier is control lock and not a fuel cock.

bughunter
Thanks for the confirmation of my guess Kenneth! I glued stretched sprue into the socket for later sanding.

René "Lord Bilbo" Bartholemy
Bughunter "not going the extra mile"? 🤔
Usurper!
What have you done to the real Bughunter? 🤣

bughunter
Don't worry, I'm okay. I still go the extra mile, but where it makes sense and is visible.
The fuselage is now closed and other small things done.

Alec K
You are making a lightning progress Frank. I can barely keep up! The added detail is, as usual, superb 👍

babak chalangi
definitely watching this

bughunter
Alec, that is a Revell Level 4 kit with only 58 parts according to the box. Ok, the PE set and the belts doubles the number and there is room for a little scratch work, but the fit is fantastic! That saves a lot of time.
I have the Mr.Paint True Blue on order and hope it will arrive soon.