Новостная лента

Nicolas
Following

Dave Flitton
Watching. The build is great, so far.

Bruce Huxtable
Really liking all the extra care you are putting into this, and the 'soft' camo looks great 👍

Trez Mackenzie
Thanks Bruce - I must say it's been a bit of a struggle so my expectations are not too high for this build. More build experience required!

Neuling
Very good first impression! More photos please!

Thib
Thank you very much, more pictures are coming

Desert Marlin
The REEDOAK 3D Printed Pilots are awesome!

Desert Marlin
This project will have both pilots on the intercom and watching the engine startup process. That is why the same type figure is used in both cockpits. They both monitor the engine to ensure that the EGT and RPM is increasing appropriately. Each has their hand on the control stick to be able to open their MIC as they confirm everything is normal at start. The plan is to have the aircraft loaded with a Nuke (Apache Cruise Missile?). Seems appropriate to me for the days we live in now...

Desert Marlin
Have to pause this one until I get the BIG ED kit #33216...

Treehugger
Maybe go for resin seats as well?
Seems like kit plastic never can compete with resin seats. 🙂

Though, I no longer crave for resin interior for the cockpit because of the work, but seats are ok.

Desert Marlin
I'll paint these up and see if I can tolerate them. If they are too bland, I have time to change my mind! Thanks for the idea!

Desert Marlin
Great video of the weapon that goes with this version of the Mirage 2000N

Youtube Video

Desert Marlin
Time to return to the 2000N... Let's Nuke something!

Desert Marlin
I got the ResKit Mirage 2000N Cockpit Set (Detailed Version).

Desert Marlin
As I have begun work on this kit, I am yet again struck by the lack of information in the variations and options provided in the kit. For example, the tail tip is not called out that applies to the 2000N version. While the nose of the 2000D is provided in the kit, it has to be modified to make it correct for the 2000N. Oh bother…

Desert Marlin
Selected "most appropriate" tail tip and mounted the correct nose to fuselage.

Desert Marlin
Okay, now I'm excited to get some paint on this cockpit!!! ResKit, you guys have done some great work with your 3D Resin Printing!

Desert Marlin
I'm back to it!

Treehugger
Oh, did you fiddle with the nose part to make it match the N version, or did you have to buy aftermarket nose for the N version? I have this kit in my stash, but haven't really looked any it yet.

Desert Marlin
I'm using the D nose but converting it to an N version. I'm also closing the "sucker doors" on the inlets to represent an engine that is not yet started... I'm assuming initial hydraulic power is applied from the APU and auxiliary hydraulic pumps have brought the gear door up. I'm going to close the speed breaks for pre-engine start configuration...

Eric Thornton
Looks like BAM has some corrected noses still need the N one. Maybe reach out to him. I could use the corrected nose for this kit also. The Reskit stuff looks amazing.

bam-models.com/produ..2000-corrected-nose/

Desert Marlin
Thanks for the heads up! The BAM nose looks fantastic! Sadly, the 2000N nose has a pitot tube and does not have the RDY antenna lines. It seems that much of the 2000N systems are somewhat earlier than the -5 systems. Everything I can find on the 2000N seems to be somewhat austere compared with the 2000-5. The ResKit cockpit is worth every penny!

Mr D
Like it 😀👍
Nice when the pilot looks like he's actually doing something and engaged with the craft.

Desert Marlin
Thanks. It's really sad to remove detail from the ejection seat, but that is the only way to get the pilot in place...

Ben M
The pilot looks amazing.

Desert Marlin
The pilot is from REEDOAK. They have several different figures in various poses so the realism can be developed based on the aircraft scenario. This model is being build to represent events just prior to engine start.

Desert Marlin
Remaining cockpit items:
1. Glass
2. Decals on seats
3. A little more weathering
4. Fix pilot's France Flag
5. Add WSO's Right shoulder patch
6. Check that I can get the canopy actuators in after everything is assembled...
7. Add HUD glass

Martin
Cool project! I have my Popcorn ready, so I'll follow closely!

Laurent VILLANUEVA HELLER ForEver
great

Valters Orlovskis
So at last the most complicated part of kit (truck) is completed. Unfortunately couldn't get rid of "orange peel" effect on body, tried two times with different paint/warnish combinations (I wanted to achieve silky gloss finish), but result was almost the same. Anyway too much time is spent on this kit so I leave all as it.

Alexander Grivonev
Finish looks pretty decent👍 what paints did you use?

Valters Orlovskis
Thanks, Alexander!
For body I use Alclad Black Base + 3 wet coats of ModelMaster Sealer for Metalizer.

Valters Orlovskis
Really terrible kit. But at last it is finished!

Rafael Gonzalez
You did a fantastic work on it Valters, if is a terrible kit it doesn't show thanks to your skills 👌🏼👏🏼👏🏼👏🏼👏🏼

Neuling
Very well done!