Новостная лента

Guy Rump
Very nice build! 👍

CaptGPF
One word - perfect

Villiers de Vos
Very nice work and effects.

John
I am in awe of your metallic finishes. 👍

Mid Franconian
A pleasure to look at! I like the classic RCAF 104 loadout with 5 x BL755.

Michael Kohl
I love the canadian Starfighters. Great to see suchban excellent model of them.

gorby
I think you win this weeks prize for most heavy duty modelling tool. 😄
Looks a very interesting conversion.

Lenny Li
I think that kind of set up can tool a real bogie!!

Neuling
Watching .....................

Jakko ‌
> I think you win this weeks prize for most heavy duty modelling tool. 😄

Probably, yeah 🙂 It's a metalworking lathe, so a bit overkill for just turning down the seam on those wheels, but I didn't feel like aching fingers from scraping them down with a knife — I get those even when I hold them in a modelling vice, never mind just between my fingers.

> that kind of set up can tool a real bogie!!

Having seen a disassembled Sherman bogie up close, I must say I think this one is a size too small for that 😉

Ben M
👀 fascinating vehicle.

Mr D
Looking good, weld's coming on nice 👍

Ben M
How did you hold the wheels in the lathe?

Jakko ‌
@Mr D: that's not the welds yet, it's just the filler needed to plug the gaps 🙁 I'm still debating how to add all the weld seams.

@Ben M: An M2 screw, about 2 cm long, through the hole in the wheel, with a nut to tighten it. It needs to be fairly tight else chances are the wheel will stop as soon as the chisel hits it. On Asuka two-piece wheels, you need to do this before assembling the parts, because the hole on the piece to be glued in is smaller than on the part that has the tyre moulded on it.

Ben M
Thank you, I can envision the setup. I have a small lathe and arthritis in my hands, this technique could help me a lot. Thanks!

Mr D
Regarding weld's l have seen super glue used through a fine tip, you need steady hand n move in pattern to create weld.
Sorry l was looking at the resin 🤔🤣.
Good stuff be keeping eye
On progress 👍👍

Jakko ‌
@Ben M: What also works is a modeller's vice. Clamp the wheel in that, scrape down the seam with a straight knife over a third or so of the wheel, then unclamp and turn it, and repeat. If I scrape more than about two or three wheels by hand, my fingers ache enough that I have to stop, so the vice helps a lot. But you also get a lot of plastic scrapings all over your modelling area, so this time, I figured I'd put those in someone else's hobby room instead for a change 😉

@Mr D: Hahaha! The ones on the resin were put there by Resicast 🙂 But I'll now have to make ones that look similar, or at least not out of place next to them. I'm thinking a thin string of two-part epoxy, textured with a sharp tool.

gorby
I've just seen an Uncle Nightshift vid on adding weld seams:
Youtube Video

Jakko ‌
Thanks for that.

Mr D
Good video 👍, the finish on the flat plate work looks authentic, l think it's had better rough cast look from the brush stippling before he added the putty coat.
Good idea on the weld , epoxy putty best as regular epoxy levels out again.

Jakko ‌
I've begun to add the weld seams now — see photo 23 🙂 Basically, Magic Sculp two-part epoxy putty that I mixed up a very small amount of, then took even smaller amounts from that and rolled it as thin as I could in my hand before pressing it into the join between the parts. Getting it to stick there is tricky, especially once I began texturing it with the tip of a knife — it wants to adhere to skin and steel much better than to plastic, unfortunately 🙁 But with a bit of perseverance it does eventually stick.

Pietro De Angelis
Fantastic work, congrats!

David Taylor
really coming along.

Jakko ‌
Thanks 🙂

Robert Podkoński
I see some heavy duty equipment here and a lot of elbow grease... Good job so far, Jakko! Keep it up!

Jakko ‌
Thanks, though this is fairly straightforward. The most difficult part was finding a good way to curve the splash plates, really.

Pepe
Looking

gorby
You're doing some excellent work on this.

Jakko ‌
Thanks 🙂

Guy Rump
Looking great, following. 👍

Jakko ‌
Cool, nice to have you along 🙂

Mr D
Taking shape now, the green welding joints are looking a better medium.
Interesting to see an adaptation taking place of the original.
Thanks for your posts, good to see steps
👍👍👍

Christian
Hallo Stefan, hab das selbe Modell im Regal. Bin gespannt wie deine wird, soweit schaut das richtig vielversprechend aus. Und ich bekomme bei deinen Bildern richtig Lust, den Bau der Messerschmitt ebenfalls zu starten!

Christoph Kunz
Nice Idea with the tape and decal combo 👍

Stefan L.
@Christian Hallo Christian, bist jetzt sind mir bei dem Modell keinerlei Probleme aufgefallen, alles passt wunderbar zusammen , kann dir nur empfehlen das Modell zu bauen. Selbst wenn das Modell verglichen mit den neuen Tamiya oder Eduard Modellen weniger Details aufweist, macht es sehr viel Spaß diese Details selber hinzuzufügen und selbst wenn man die Details weglässt, ist das Modell sehr schnell gebaut und für den Preis meiner Meinung nach sehr zu empfehlen. Abgesehen davon sind die meisten neuen Bausätze der BF109 von der G Variante und nicht von der E Variante. Hoffentlich kann ich dich mit meinem Bau inspirieren, dein Modell auch anzufangen 🙂

Stefan L.
@Christoph Kunz thank you!

Christian
Schaut sehr gut aus Stefan! Die Sache mit den Nieten für meine E hat der Vorbesitzer meines Kits mit einem kompletten Satz Nieten Decals von HGW gelöst. Für andere Projekte hab ich auch schon über ein solches riveting Tool nachgedacht?! Hab jetzt einmal geplant, das Modell über den Winter zu bauen. Allerdings will ich vorher noch meine UH-1B und die MH-60K zu Ende bringen, bzw. diese parallel dazu bauen. Bis Mitte November bin ich noch sehr mit unserem Hausprojekt und der Landwirtschaft eingeteilt. Auf alle Fälle bin ich auf das Resultat deiner Bemühungen gespannt!!!

Desert Marlin
My favorite is the Emil variant.

Stefan L.
@Christian Ein solches Nieten Set habe ich auch gesehen aber um ehrlich zu sein, ist es mir nicht wert, den Preis des gesamten Modells noch einmal für Nieten zu zahlen. Gut für dich, dass der Vorbesitzer sie schon gekauft hat, ich würde sie auf jeden Fall benutzen, bin schon gespannt wie deine Emil aussehen wird!

Stefan L.
@Mark Lawrence since this is my first BF109, I'm no expert yet but I also like the Emil just simply due to the fact, that the Gustav variants seem to get build more often, which why I like seeing the Emil instead of yet another Gustav!

Desert Marlin
Those from the Schlachgater are also quite interesting.

Sergej I
Great progress, Stefan 👍

Stefan L.
@Sergej I, thank you so much!

John
Looks great Stefan and nice cockpit. Neat trick on the fishing line, thanks.

Stefan L.
@John thank you for your nice words! Always happy to spread some tips! 🙂

Marcin Dudek
Wow, thanks for the detailed description! I learned a lot only by reding. I'm looking forward for more.

Stefan L.
@Marcin Dudek I really appreciate your comment Marcin! I wasn't expecting that someone really reads all the stuff I write but seems I was wrong! It makes me really happy that you found some useful tips even though this is just my second proper model and I am far from being a somehow experienced modeler. Take care and keep modeling 🙂

John
For the boundaries since it's straight edge you can just touch it up with a post it note pretty easily.

Stefan L.
@John thanks for the tip! I would have masked it again but the post it method is much easier, didn't think of that, thanks alot!

Christophe
Thank you for sharing!

Stefan L.
@Christophe your welcome! Appreciate it and thanks for the comment!

John
Nice mottling Stefan. 👍

Stefan L.
@John thank you very much John!

Doubtingmango
Fantastic build with a great narrative filled with useful tips

Stefan L.
@Doubtingmango thank you for your kind words!

John
Looking really good!

Stefan L.
@John thanks!

Jennifer Franklin
That's a neat trick with the fishing line; lots of great detail on your work. Very nice work so far.

Stefan L.
@Jennifer Franklin thank you for the nice words 🙂 I'm really trying my best and hope that my increased experience will show at the end result, especially when compared to my first ever modelkit, the Eurofighter

TH SCALE MODELS (Thomas Haberl)
Looking good, especially knowing this is your second build. 1:48 is a good scale to start with. Thumbs up and keep modeling 👍

Stefan L.
@Thomas Haberl thank you very much! 🙂

Guy Rump
Looking great! 👍

Stefan L.
Thank you!! 🙂 @Guy Rump

Gerald
👍

John
Nice job on the exhaust/gun stains. 👍 You are right, you really can't go too thin on that mix. I'm cheap so I just use XF-1 (and other colors for allied planes that used leaded gas) thinned way down with isopropanol and make multiple passes until it looks right. I also add some pastel/pigment to give some body to the stain as well like you suggested. Looking good, Stefan!

Stefan L.
@John thank you!! Tonight I also used black pigment in the core and close to the gun barrels to give the stains a more interesting look, happy with the result, pictures will follow soon! 🙂 And thanks for the tips, appreciate them alot! 🙂

John
The heat staining is next-level, as is the whole finish.

Michael Kohl
Absolutely. Like it a lot.