Новостная лента
Desert Marlinдобавил новый фотоальбом.
51 изображения
Israeli P-51D D-191 (2302) [COMPLETED]
1:32
A really pretty Scheme!
Проект: P-51D Israeli D-191 (2302)
40 14 April, 21:47
Desert MarlinWell, the polycap that is supposed to link/sync the left and right elevators fell out during the process of joining the fuselage halves. So I had to saw out the little housing that was supposed to hold the polycap in place and set it manually. Looks like I have one "unforced error" so far...
26 April, 22:57
RandoThat Merlin is looking great. Looks like it came with the kit? Must be a lot easier than old resin, lol
27 April, 00:09
Desert MarlinIt's close to time to add the canopy and mask for paint. Lots of weathering yet to go. And the gun bays are looking a bit bland. Needs some additional paint and wiring.
1 May, 06:15
Desert MarlinTime to close up the cockpit and prep for paint. Going to be one of those traditional natural metal schemes with lots of wear and tear...
3 May, 05:06
RandoYep agreed Ky, my next P-51 will definitely be a Tamiya. How did detailing the gun bays go Marlin?
3 May, 14:37
Desert MarlinStill working on them. The fit has had only one issue that was even close to being worth mentioning. The right wing gun port on the leading edge did not fit perfectly. So I have had to do a little filling on the undersurface. The underwing scoop was almost an issue but seems to have settled into place. WARNING: one must fit the AILERONS BEFORE THE FLAPS. Otherwise the photo etched hinge does not get locked into place by the steel shaft from the outboard end of the flap. Missed this so it was unforced error #2...
3 May, 20:53
Desert MarlinOkay, after looking at some of the real aircraft, I am not sure there is any detail needed except to weather the bay and guns. I was expecting some electrical or other pipes/wiring, but alas, there does not appear to be any...
3 May, 21:41
Desert MarlinI'm back! So the masks provided are intended to be applied to the outside surface. However, it's really hard to mask the interior surface, so I cut the masks and applied them to the inside of the glass and then used Scotch tape for the outside. Leaving the interior a little "over masked, the black primer added to the outside with the flat black interior will create a nice effect overall.
2 June, 23:44
Desert MarlinBack at it! Prop is done, not yet weathered. Needs some scuffing along the leading edges.
1 July, 04:14
Desert MarlinI'm using Alclad and Metalizer. Sadly, my collection of Metalizer is shrinking. My choice for masking tape is 3M PostIt Notes. They work really well on the soft surface of Alclad Primers and Paints. Looking to seal it up next and start the process of marking/weathering.
4 July, 17:04
JohnI love the finish of Metalizer but hoo boy is it fragile. I hear you on supply. I'm all out of aluminum; stainless steel and jet exhaust are all that's left. 🙁
Your IDF Mustang is looking great, however!
4 July, 18:02
CaptGPFGoing to steal your post it notes trick for my next metallic project. Even i]with Xtreme Netal paints, I still have to wait a couple of days after I seal it with gloss - thanks Marlin!
5 July, 15:40
French camp 78владеет этим предметом
F-16D block 50 3D-Printed & coloured Interior on decal paper
Quinta Studio 1:48
QD48408 14 July, 04:18
French camp 78владеет этим предметом
McDonnell Douglas
F-4 Phantom II - FOD Covers for Zoukei-Mura 
ResKit 1:4814 July, 04:17
Eduardo Arguijoвладеет этим предметом
Marine Corps Bomber
SB2U-3 Vindicator VMSB-241, Battle of Midway Accurate Miniatures 1:48
480202 2005 Новые детали 14 July, 04:08
Richard Mortimoreпометил этот товар как заказанный
Fallschirmjäger 8cm Mortar Team (Italy 1944)
Dragon 1:35
6215 2004 Новая разработка Несколько моделей (2)14 July, 04:06
/ru/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=ru
35
35
/ru/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo