[Beemax] BMW M3(E30) - WIP
![Album image #1 Album image #1](/albums/img/8/1/8/1731818-37066-16-720.jpg)
Before I start, I duplicated the grill part because I thought I could use it on a very poor quality Fujimi kit.
BMW M3 Type E30 (Fujimi 12572, 1:24)
BMW M3 Type E30 (Fujimi 12572, 1:24)
![Album image #2 Album image #2](/albums/img/8/1/9/1731819-37066-75-720.jpg)
I removed protruding parts on the body.
![Album image #3 Album image #3](/albums/img/8/2/0/1731820-37066-19-720.jpg)
Fender was too thick, so I shaved it off thinly.
![Album image #4 Album image #4](/albums/img/8/2/1/1731821-37066-74-720.jpg)
I did the same thing to the rear fender.
![Album image #5 Album image #5](/albums/img/8/2/2/1731822-37066-34-720.jpg)
This kit can be manufactured in either #3 or #11.
In the case of vehicle #11, only one hole must be drilled in the marked area (refueling port?). (#3 requires two holes to be drilled)
In the case of vehicle #11, only one hole must be drilled in the marked area (refueling port?). (#3 requires two holes to be drilled)
![Album image #6 Album image #6](/albums/img/1/7/3/1732173-37066-57-720.jpg)
Scraped panel-line and sanded.
![Album image #7 Album image #7](/albums/img/1/7/4/1732174-37066-68-720.jpg)
Washed.
![Album image #8 Album image #8](/albums/img/1/7/5/1732175-37066-73-720.jpg)
The tow hook was too thick, so I sand it thin.
The thickness is not uniform, but it doesn't really matter since only the end will be visible anyway.
The thickness is not uniform, but it doesn't really matter since only the end will be visible anyway.
![Album image #9 Album image #9](/albums/img/1/7/6/1732176-37066-57-720.jpg)
The muffler was blocked, so I drilled deep.
Drilling the exact center of a cylinder cut at an angle is a bit stressful.
Drilling the exact center of a cylinder cut at an angle is a bit stressful.
![Album image #10 Album image #10](/albums/img/2/8/5/1733285-37066-44-720.jpg)
When I finished trimming the parts, it was only a handful. 🙂
![Album image #11 Album image #11](/albums/img/2/8/6/1733286-37066-34-720.jpg)
The antenna was too thick, so I decided to replace it with metal wire.
![Album image #12 Album image #12](/albums/img/2/8/7/1733287-37066-98-720.jpg)
The neck of the original part was cut off, and the stainless steel tube was cut and trimmed.
![Album image #13 Album image #13](/albums/img/2/8/8/1733288-37066-55-720.jpg)
I finished it by drilling a hole in the center of the root and inserting the cut tube and iron core.
I found out about it late, but when I looked at the manual, I saw that there was a spring, but it was annoying, so I'll just skip it.
I found out about it late, but when I looked at the manual, I saw that there was a spring, but it was annoying, so I'll just skip it.
![Album image #14 Album image #14](/albums/img/5/0/1/1734501-37066-36-720.jpg)
I used the Zoom On product for masking the windshield.
![Album image #15 Album image #15](/albums/img/5/4/1/1733541-37066-93-720.jpg)
Since this is a light-colored vehicle, we painted it black to block light transmission.
And I collected other parts that needed to be black and painted them as well.
And I collected other parts that needed to be black and painted them as well.
![Album image #16 Album image #16](/albums/img/5/4/6/1733546-37066-25-720.jpg)
Uh-oh, why is this still here?...
![Album image #17 Album image #17](/albums/img/7/7/0/1733770-37066-57-720.jpg)
There is no space to hold the wing when painting, so I have to make a handle.
In that case, after finding an appropriate length on the runner...
In that case, after finding an appropriate length on the runner...
![Album image #18 Album image #18](/albums/img/7/7/1/1733771-37066-45-720.jpg)
That fixed like this.
![Album image #19 Album image #19](/albums/img/8/4/9/1733849-37066-18-720.jpg)
I painted white surfacer and other colors.
![Album image #20 Album image #20](/albums/img/9/2/4/1733924-37066-23-720.jpg)
Uh-oh, why is this still here? again...
![Album image #21 Album image #21](/albums/img/9/2/5/1733925-37066-53-720.jpg)
I should have painted the bottom and interior white anyway, but I forgot, so I masked the bottom at this point.
![Album image #22 Album image #22](/albums/img/5/0/2/1734502-37066-84-720.jpg)
The inside of the door could be painted with a brush, but I just masked it.
I didn't want to paint the roll cage one by one, so I assembled it in advance.
I didn't want to paint the roll cage one by one, so I assembled it in advance.
![Album image #23 Album image #23](/albums/img/5/0/3/1734503-37066-72-720.jpg)
White surfacer.
![Album image #24 Album image #24](/albums/img/4/3/5/1737435-37066-60-720.jpg)
Gloss white.
![Album image #25 Album image #25](/albums/img/4/3/6/1737436-37066-12-720.jpg)
Liverty decal started.
![Album image #26 Album image #26](/albums/img/0/4/0/1739040-37066-35-720.jpg)
Attached all decals.
![Album image #27 Album image #27](/albums/img/0/4/1/1739041-37066-59-720.jpg)
For some reason, I have a feeling it will be a silverring.
![Album image #28 Album image #28](/albums/img/4/4/8/1754448-37066-10-720.jpg)
I fixed silverring.
![Album image #29 Album image #29](/albums/img/4/7/1/1754471-37066-50-720.jpg)
The areas where the decals were short and the sections where the plastic was thick were painted with a brush.
![Album image #30 Album image #30](/albums/img/4/7/2/1754472-37066-29-720.jpg)
While I was brushing, I also proceeded with partial painting.
![Album image #31 Album image #31](/albums/img/4/8/5/1754485-37066-51-720.jpg)
If you look at the assembly instructions, it looks like the optional parts include a kill switch, but it is not included in the basic configuration.
So I heated and stretched the runner for make two kill switch.
So I heated and stretched the runner for make two kill switch.
![Album image #32 Album image #32](/albums/img/4/8/6/1754486-37066-95-720.jpg)
I cut the pla-plate into small pieces, glued them, sanded the edges to make them round, and painted them red.
![Album image #33 Album image #33](/albums/img/5/9/1/1754591-37066-83-720.jpg)
Clear coated. (x4)
![Album image #34 Album image #34](/albums/img/5/9/2/1754592-37066-51-720.jpg)
Sanded.
The clear was not curing well, so I let it dry for a long time.
The clear was not curing well, so I let it dry for a long time.
![Album image #35 Album image #35](/albums/img/8/9/4/1754894-37066-50-720.jpg)
Polished.
![Album image #36 Album image #36](/albums/img/8/9/5/1754895-37066-92-720.jpg)
Painted panel-line.
![Album image #37 Album image #37](/albums/img/1/7/9/1755179-37066-94-720.jpg)
I painted with paint brush to under body.
It would have been nice to have a Kevlar fiber pattern decal on the back of the seat, but the assembly instructions only say to paint it GSI H79 (dark yellow).
It won't be noticeable once it's completed anyway. 😉
It would have been nice to have a Kevlar fiber pattern decal on the back of the seat, but the assembly instructions only say to paint it GSI H79 (dark yellow).
It won't be noticeable once it's completed anyway. 😉
![Album image #38 Album image #38](/albums/img/1/8/0/1755180-37066-81-720.jpg)
I coated the emblem decal with UV resin.
![Album image #39 Album image #39](/albums/img/1/8/1/1755181-37066-19-720.jpg)
Result.
![Album image #40 Album image #40](/albums/img/4/6/3/1755463-37066-86-720.jpg)
There were decals that had not been attached yet, so I also attached the emblem in advance.
![Album image #41 Album image #41](/albums/img/4/6/4/1755464-37066-58-720.jpg)
Ready to assemble.
![Album image #42 Album image #42](/albums/img/5/2/1/1755521-37066-84-720.jpg)
Assembled bottom parts.
However, in my experience, if I install the wheels first, interference often occurs when join with the body shell, so I decided to assemble the wheels later.
However, in my experience, if I install the wheels first, interference often occurs when join with the body shell, so I decided to assemble the wheels later.
![Album image #43 Album image #43](/albums/img/6/5/6/1755656-37066-80-720.jpg)
It was decided to detail-up only the shoulder straps for the seat belts.
![Album image #44 Album image #44](/albums/img/9/4/7/1755947-37066-79-720.jpg)
I need a tiny hook. (I found this in an old etching I used to use)
![Album image #45 Album image #45](/albums/img/9/4/8/1755948-37066-83-720.jpg)
I drilled the holes, put the hooks through, and hung the seat clips.
![Album image #46 Album image #46](/albums/img/3/3/0/1756330-37066-24-720.jpg)
Assembled interior.
![Album image #47 Album image #47](/albums/img/3/3/1/1756331-37066-45-720.jpg)
Another view.
![Album image #48 Album image #48](/albums/img/3/3/2/1756332-37066-19-720.jpg)
Another view.
![Album image #49 Album image #49](/albums/img/0/0/1/1757001-37066-20-720.jpg)
Glued the nylon mesh to the front bumper.
I had to make some cuts where indicated to get it to fit well. (the mesh was included in the kit)
I had to make some cuts where indicated to get it to fit well. (the mesh was included in the kit)
![Album image #50 Album image #50](/albums/img/0/3/7/1757037-37066-39-720.jpg)
For the reflector of the winker, I cut and attached a silver foil sticker.
![Album image #51 Album image #51](/albums/img/0/3/8/1757038-37066-27-720.jpg)
Front bumper done.
![Album image #52 Album image #52](/albums/img/2/6/5/1757265-37066-31-720.jpg)
Assembled face.
The kidney grille and headlamp covers didn't fit well, which caused some stress when assembling.
The kidney grille and headlamp covers didn't fit well, which caused some stress when assembling.
![Album image #53 Album image #53](/albums/img/2/6/6/1757266-37066-60-720.jpg)
Attached side mirror to side window.
![Album image #54 Album image #54](/albums/img/2/9/9/1757299-37066-43-720.jpg)
Glued windows.
![Album image #55 Album image #55](/albums/img/3/0/0/1757300-37066-94-720.jpg)
Inserted kill switch
![Album image #56 Album image #56](/albums/img/4/6/7/1757467-37066-95-720.jpg)
Assembled front.
![Album image #57 Album image #57](/albums/img/4/6/8/1757468-37066-38-720.jpg)
Assembled rear.
![Album image #58 Album image #58](/albums/img/7/0/2/1757702-37066-57-720.jpg)
Combined upper/under body.
I had to cut the male pins of the front splitter short so that it could fit tightly with the front bumper.
I had to cut the male pins of the front splitter short so that it could fit tightly with the front bumper.
![Album image #59 Album image #59](/albums/img/7/0/4/1757704-37066-91-720.jpg)
Lastly, attach the remaining antenna, fasteners, etc. and it's done.
![Album image #60 Album image #60](/albums/img/7/0/3/1757703-37066-95-720.jpg)
Done.
![Album image #61 Album image #61](/albums/img/7/0/6/1757706-37066-55-720.jpg)
Finish
![Album image #62 Album image #62](/albums/img/7/0/5/1757705-37066-44-720.jpg)
Thanks for watching 😉
Комментарии
40 19 May, 09:40
![](/profiles/img/37066-788-s.png)
Painting the shell requires drying time, so I started working on something else in the meantime, and it happened to be a BMW again. 😉
28 May, 08:05
![](/profiles/img/28845-385-s.jpg)
Presumably a good-enough decal softener will help against silvering, where silvering is air tapped under the decal because of the rough texture of the painted surface.
Solvaset = stronger decal softener
MicroSol = default decal softener?
After applying a decal softener, the decals MUST NOT be touched, even if it starts looking wrinkly. The wrinkles all disappear after a while.
One thing I like to do after airbrushing on primer and also paint, is to gently go over with sanding sponge, but never over edges as that will surely removed paint off the plastic, but large flat surfaces are typically safe to sand down very gently, to create a more flat surface. For this to work, it is important that the base layer, the primer paint, is sanded flat first, else the uneven primer paint will show through the paint layer, if you only sand the paint layer on top.
30 May, 06:26
![](/profiles/img/user-s.jpg)
I'm using Tamiya Mark Fit Super Strong. Just apply the softener to the surface of the decal and after a couple of minutes, gently press it onto the surface with a cotton swab. If the decal is not welded, then it may fall off in pieces along with the varnish 🙁 .
30 May, 11:59
![](/profiles/img/49481-557-s.jpg)
Love the use of UV resin on the logo badges, an idea I'll use from now on many thanks
26 June, 07:51
Album info
FHD images.
1/2 - motorart.tistory.com/766
2/2 - motorart.tistory.com/781