база данных по моделизму | управление закромами
smokeriderdon
Donald Dickson II (smokeriderdon)
US

1-72 Tornado IDS

Комментарии

1 28 November 2017, 01:26
Donald Dickson II
A lot of progress made. I did all the same work and primed it with mr. Surfacer 1500 black. Then the two gray colors topside neutral gray bottom light ghost. At this point it occurred to me that this was going to be a tail sitter and I hadn't put any weight in the nose. So I carved a flap just in front of the nose gear well, squished some split shot and showed them in there then poured super glue in there.

Once that was sealed up and fixed I went back and re-sprayed some areas. Then at that point we were ready for the exhaust. I used Alclad stainless steel, burnt iron, light burnt metal, and a very small bit of hot metal blue. Then I put on the vertical stabs. Next I have to paint the nose cone and then I will gloss it up and do all these wonderful decals.
7 December 2017, 07:30
Martin Oostrom
She looks very nice Donald. Keep it up 👍
7 December 2017, 07:51
Donald Dickson II
I swear I am snake bit with models right now. Sat down to go to work on the decals. The pics pretty much say everything. They are un usable. Even with a coating of decal sealant on them. So gonna have to set this aside until I find a set of decals I like.
10 December 2017, 19:43
Clifford Keesler
You just are not having much luck lately are you. Hope it gets better.
10 December 2017, 22:07
Martin Oostrom
Ooh. That's tough.
10 December 2017, 23:01
Donald Dickson II
Clifford, I sure as hell am not. LOL Ah well, is what it is. I did find an interesting and colorful set that go on a black paint job. So going over this one wont be a big issue.
11 December 2017, 00:06
Donald Dickson II
So there is the decal set I ordered. We will see how those work when i get them.
11 December 2017, 04:53
Martin Oostrom
You do know that the picture of the decals states 1/48 and your build is 1/72?
Or is the picture just to show us what you're getting?
11 December 2017, 06:36
Donald Dickson II
The one I got was listed as 1/72. Thats just a pic to show.
11 December 2017, 07:55
Clifford Keesler
That will be a colorful bird. Good luck. Looking forward to seeing it.
12 December 2017, 00:38
Donald Dickson II
Got the new decals today. Painted her black, did the intakes and wheel wells and glossed her up. Give it a day or two to set well then start putting the decals on. An interesting note in the decal instructions about this plane. It evidently flew with absolutely nothing hanging. No tanks, no pylons, nothing. Debating on whether to fill the holes or leave them be.
16 December 2017, 05:39
Brian Jones
Well done for hanging in there and changing scheme after Decals let you down. She will be worth the effort once finished
16 December 2017, 06:52
Ekki
Watching.
16 December 2017, 10:40
Holger Kranich
Nice one!
16 December 2017, 12:15
Donald Dickson II
So, I got to work on the decals tonight. First, these are very nice decals! Nicely done, good color and opaque. Only thing is the numbering on the sheet. You have to pay VERY close attention to determine which is which. Just a little point to direct you. Not a biggy really. They went on nicely and settled in mostly on their own. In the directions, Skyhart says not to use decal set, and mostly its not needed. Mainly over the curves in the fuselage. Also, this set is clearly intended for wheels up. Had to tack the cover in place and carefully cut the decals once they were on just right.

So the left side is done. The fun part will be doing the right, lining all of the parts up AND getting them even with the left side.
20 December 2017, 06:19
Clifford Keesler
You can do it man! LOL.
21 December 2017, 02:39
Donald Dickson II
LOL Oh, I will. Just gonna be a challenge. 😄
21 December 2017, 03:57
Donald Dickson II
Alrighty! Wrapped this one up in time to be the last of 17. There are a few things I need to figure out still. I did not fill in the holes for the pylons. As I mentioned, this plane supposedly flew with these markings with nothing at all under it. Not sure yet if I want to say screw it and put somethingt here regardless or not. I have ordered a master brass pitot tube, so that will be taken care of shortly. I realize the one on there is crooked.

As I said, the decals were good. But, they WERE fragile. Very easy to tear them. I managed to mix up the pink and blue to cover any of my screw ups. 😄

Overall, not my best, but certainly not my worst. Still wish the original decals had been good though. Argh.
28 December 2017, 19:52
Donald Dickson II
Oh, I had to use the kitchen window sill because the lights were washing out the colors. Badly. Even indirect. So i had to do the natural light thing. And it is flipping -13 celsius with the wind chill here. So I was NOT going outside to do these pics!
28 December 2017, 19:57
Ekki
Very good result. 👍
29 December 2017, 11:06
Clifford Keesler
Nice one Sir.
29 December 2017, 15:45
Martin Oostrom
She turned out really nice despite your setbacks. Well done Donald
29 December 2017, 15:58
Donald Dickson II
Thank you gentlemen! 🙂
29 December 2017, 18:52

Album info

Well, I started this one a while back, before I moved back in July. I had forgotten about it until Clifford mentioned he was doing three and I should try that. He was joking, but of course I took it to heart. LOL

So I was looking around for something easy to slip in with the Phantom and Bone, and my eyes focuse don the packing box this kit and someother stuff was in. And I remembered. And as Mr Keesler didnt say try 3 at a time that havent been started...

So here we go! The cock pit was done and ensconced in the nose already. I got the intakes together and the fuselage together with wings last night.

26 изображения
1:72
Завершённые
1:72 Tornado IDS Sonderanstrich 100.000 Flugstunden JaboG 33 (Syhart 72-077)

Все альбомы

Посмотреть все альбомы »