newsfeed

gorby
Impressive dio!

Pietro De Angelis
Beautiful work under every aspect, congrats Mathias!

Mathias Decommere
Thank you very much Pietro and Gorby! Means a lot!

Derek Rothfus
Wow! Great job. Love the blood effects on the windshield.

Mathias Decommere
Thx Derek! This was indeed a fun part to make 😁

Mr James
Great scene and dio. Love the flat tyre. Lovely dio

Mathias Decommere
Thank you Mr James! And also for the likes!

Robert Podkoński
Congrats, Mathias! Well deserved prize!

Bruce Huxtable
You've been as busy as your cast of players! Creativity plus modelling skills well demonstrated 🙂 Congratulation s🙂

Mathias Decommere
Thank you very much Robert and Bruce! I'm very happy!

fire snail
wow 很精彩的故事演绎 我也要努力做出场景

Bobby Thumbs
congrats mathias a well deserved prize

Rui S
Great Dynamic scene. Well done. Congratulations, Mathias 👍

Mark Sherwood
Top notch Mathias, congrats. 👍🥸🤟🥸🤘

Olivier
A real story you gave us here...

Mona
amazing detail, even the flat tire .well done a much deserved prize

Mathias Decommere
Thank you everybody! Your comments mean a lot to me!

Sy Bar
Was going to do the Battle of Britain version of this kit but I'm temped to have a go at some winter white wash and the wasp is cooler than the shark mouth 😎

Nicolas
Following

István Szücs
I also have Bf-110 from the Airfix, I will build an Italian night fighter. The sprues are the same, so I'm watching!

Sy Bar
Cheers guys.
I'm have a go at riveting, but going freehand as at this scale using tape was taking so long. I also not sure how much they will stand out on finish kit, but with the wonky line in parts they will probably bee seen from mars 🤣

Mark Sherwood
Looking good so far, like the underside. 🥸👍

Sy Bar
Cheers #Mark

Skyhiker
Sy, how was the fit on this kit?

Guy Rump
Looking good, following. 👍

Sy Bar
Cheers #Guy 👍
#Skyhiker I found the fit to be good, I had a very slight gap at the front but think that was as much to do with me and the fitting of the pit (not the clearest instructions there). Every thing else was fine and the canopy was a good fit, I did change order of build slightly with the tail section I glued the rear piece to the body first then added the tail (after I'd added the stabilisers/rudders) this made more sense than the instructions 😁

Sy Bar
Only issue I have with this kit are the decals. While they look great and are in perfect register, they have a large amount of film edging and are both thick and delicate at the same time🤪
Having a hard time getting them to settle into the panel lines etc. I usually just need to use micro sol but even ultimate extra strong is not have much effect. Going to have to wait till I get some Tamiya fixer, strong and extra strong hopefully one of these will help 🤞

Mr D
You should be ok with the medium one with Airfix decals,
I like a mix of Water in with the markfix...seems to keep the decal floating longer.
I did the teeth on my p40 this way.
If they started getting bit sicky...l would add bit more water....keep it floating.
Wouldn't like to do shark teeth with HB decals 🤔🤣.... The lightning ⚡ strike on my mig-15 just fell apart with hardly any working.
Good luck with it ..look forward to seeing 😃👍👍

Dave Flitton
Looking good!

Sy Bar
Cheers for advice #Mr D. Afraid this set of decals were unaffected by all solutions but the mark fit super strong did have some effect. To make head way I found I needed to add the solution then after a few seconds apply hot air from a hairdryer to 'shrink wrap' the decal. These have to be the worst decals I've come across..
I recommend anyone doing this kit to source a set of decals rather than use those provided, they are not for beginners that's for sure. I hope the carrier film will disappear under a gloss coat but I didn't want to risk it so I've only applied the larger decals the smaller ones while add great detail if cartograf here they are 90% carrier film.

Skyhiker
Why don't you just cut the carrier film away with a knife before applying them?