Sd.Kfz. 11 with Pak 40
Komentáre
26 17 September 2020, 22:15
![](/profiles/img/15656-162-s.jpg)
Welcome, Spanjaard. The frame halves are joined. Now there's the dilemma of what fuel tank to use, short or long? Reference for that in my books is scant.
17 September 2020, 22:22
![](/profiles/img/15656-162-s.jpg)
Welcome, people! I now cleaned up the wheels, because the mudholes had a lot of flash. But now there is a discrepancy between the Aber and AFV tread plates. It should be the right PE set... At least it has some fine axle restraining braces.
18 October 2020, 14:59
![](/profiles/img/15656-162-s.jpg)
Thanks, Olivier. Today I added the fender supports, the transmission and brake handles and the munition racks. Hobbyfan doesn't give any instructions, but I assumed they had to be placed perpendicular to the loading floor, leaving a crevice on top and after.
24 October 2020, 23:16
![](/profiles/img/15656-162-s.jpg)
Some additions to the cabin. I dry-fitted the engine but I decided to order the Aber engine hood. The munitions locker has a roof now, after some filling at the sides.
8 November 2020, 11:29
![](/profiles/img/15656-162-s.jpg)
Welcome, Jan. The Aber hood has arrived and is bent in shape. If only it had some hinges to hang on to the vehicle, but this seems not have been the case. I will have to put it aside of the half-track. An important point is that you are expected to be in possession of the Aber basic set to be able to add the ventilation hatches and hatch actuators in the hood. Luckily I was.
15 November 2020, 21:44
![](/profiles/img/15656-162-s.jpg)
I will probably paint it black. Today I began cleaning up the Friul tracklinks. The sprockets that came with it are really a must. Then I adapted a cable clipper to calibrate my track pins. It takes time to glue the treads on.
29 November 2020, 00:40
![](/profiles/img/15656-162-s.jpg)
Thanks, guys! Just finished the Friul tracks and working on the cabin doors right now. Not all Eduard PE seems useful, like the outside door plate that is only added to be able to insert the hinges at the right place. This would make the doors too thick and it makes only for harder painting.
6 December 2020, 15:17
![](/profiles/img/15656-162-s.jpg)
Working on the ammunition hatches, but it went different than what the Aber manual said, because the manual is unreasonably asking to cut all loading bay sides 0,4mm. I just glued the PE to it, but now I have to find a way to insert the PE hinges.
14 December 2020, 22:08
![](/profiles/img/15656-162-s.jpg)
Thanks, Paulo! Today I made an update for the windshield, that is thoroughly modified with Eduard replacement parts. They even make the window hatch workable, necessitating the removal of several kit frame parts and the insertion of a piece of Friul 0,3mm wire as the axis for the hatch. Various tools were used to scrape out the frame inside.
10 January 2021, 00:47
![](/profiles/img/13846-389-s.jpg)
Nice build so far, Steven 👍👍 Why did you bore up the wheels and with which diameter? What saw is this at pic 60?
10 January 2021, 10:12
![](/profiles/img/15656-162-s.jpg)
Thanks, Joerg. Some of the wheels had flash in the mudholes, so I redrilled them.
[img1]
The saw is a photo etch set you can attach to a scalpel.
Fine razor saw blade Set No.2 (Airwaves AEM009, No)
10 January 2021, 11:21
![](/profiles/img/15656-162-s.jpg)
@Jean-Michel and Paul: I'll try to update every weekend. I guess I'm almost to the point of commencing the PaK.
10 January 2021, 13:22
![](/profiles/img/15656-162-s.jpg)
All thanks for these replies, I found the courage to finish these hatches and some PE in the trunk.
11 April 2021, 18:47
![](/profiles/img/15656-162-s.jpg)
Thanks for the compliment, I found the courage to add the front doors this weekend. Now it's only the roof and then I can start the gun build.
27 July 2021, 14:20
![](/profiles/img/15656-162-s.jpg)
Time for the PAK. The barrel is fun, but they totally botched the pre-bent splintershields. They were both a bit deformed and easily corrected, but one is completely plied to the wrong side. So I will have to flatten it again and then "counterbend" the bends. And it has to be perfect to get the spacers into the locator holes. We'll find out next time if I had to buy a new shield or not.
4 September 2021, 22:22
![](/profiles/img/15656-162-s.jpg)
It's worked out with the kit shield and both plates are now positioned with the AFV spacer set. I even have enough bolts to do a Scheunentor afterward, so that goes on the wishlist. The torsion bars are staggered, something that is arranged correctly in the kit but is not visible in the build step aspect. Therefore, checking with your Nuts&Bolts reference is really helpful. One locator block had to be removed to correctly place the extreme parts of the torsion legs.
11 September 2021, 21:58
![](/profiles/img/15656-162-s.jpg)
The wheels are now added, with some minor changes to the trailer arms. Attention is needed to only remove mold lines and not the weld beads visible in the reference pictures. It's ready to be painted now.
24 October 2021, 00:16
![](/profiles/img/15656-162-s.jpg)
Thanks, Paulo! Both gun and tractor are now in German Grey and treated to a coat of Pledge.
9 November 2021, 23:47
![](/profiles/img/15656-162-s.jpg)
I added the Hobbyfan small fuel tank, though I doubt the kit one is wrong for this, and also the drive axle fron the engine that would be visible. I installed the engine with some details painted on it. The gun shield did not align wel laterally due to my repairs on the wrongly pre-bent PE set. I tried to correct that. I painted the resin shells in brass, looking qite conspicuous.
12 November 2021, 11:40
![](/profiles/img/15656-162-s.jpg)
I deleted it, it should not have sneaked in in the first place.
13 November 2021, 08:35
![](/profiles/img/15656-162-s.jpg)
The tracklinks are connected and the Hobbyfan figures assembled. The fit is great. The Voyager grenades are prepared for painting, a PE ignition pad is added to each one.
13 November 2021, 22:12
![](/profiles/img/15656-162-s.jpg)
Thanks, Olivier. I started the dio now, therefore I added a TS-Modellbau casting to the database. I'm enlarging it so the whole assembly will fit.
15 November 2021, 22:35
![](/profiles/img/15656-162-s.jpg)
Thanks, Markus! Just painted the diorama and added some life to it. Had to make my own drain cover with a file and I will also be twrowing some dead leaves.
22 November 2021, 00:26
![](/profiles/img/15656-162-s.jpg)
Thanks, Villiers. The ammo crates are painted and the license plate and tactical sign from the picture from Nuts&Bolts are recreated. I found a Dragon decal with this sign on it. The foliage is adde with thinned PVA and compressed with glass.
22 November 2021, 23:20
![](/profiles/img/15656-162-s.jpg)
The diorama is finished, I placed the gun like after being used for a few shots and the half-track is now getting underway again with some maintenance. Being quite heavy it is pulled against the base with two wires that are slung around the axle of a roadwheel. All the reast is glued with contact glue, so the brass rounds and the hood parts are fixed well to the plaster.
12 December 2021, 13:02