DONE !! CASA CN-235
![Album image #1 Album image #1](/albums/img/8/6/6/853866-10307-21-720.jpg)
![Album image #2 Album image #2](/albums/img/8/6/7/853867-10307-95-720.jpg)
![Album image #3 Album image #3](/albums/img/8/6/8/853868-10307-11-720.jpg)
The content of the box - Vacuformed sheets. That's new to me. I am curious how this one turns out.
![Album image #4 Album image #4](/albums/img/8/6/9/853869-10307-38-720.jpg)
Let the show begin.....defining the "parts end" with permanent marker.
![Album image #5 Album image #5](/albums/img/8/7/0/853870-10307-11-720.jpg)
Getting closer to the edge with a scissor.
![Album image #6 Album image #6](/albums/img/8/7/1/853871-10307-79-720.jpg)
And even more closer with a real sharp scalpel blade.
![Album image #7 Album image #7](/albums/img/8/7/2/853872-10307-24-720.jpg)
Scisor and blade exercise is important - because now it starts with sanding. Sanding. Sanding,...
![Album image #8 Album image #8](/albums/img/8/7/3/853873-10307-43-720.jpg)
After some time you see the marker shining through...slower and carefully now continuing with a higher grade of sanding paper.
![Album image #9 Album image #9](/albums/img/8/7/4/853874-10307-62-720.jpg)
at the end...a small burr get loose from the part. Done. 🙂
how many parts are in the box...um? Ok. See you in a few weeks - have to go sanding
how many parts are in the box...um? Ok. See you in a few weeks - have to go sanding
![Album image #10 Album image #10](/albums/img/0/4/5/888045-10307-14-720.jpg)
Okay...well. When putting all those sanded parts together in a trial fit it seems that at the end an aircraft turns out - indeed.
![Album image #11 Album image #11](/albums/img/0/2/0/888020-10307-35-720.jpg)
So to get to this point it took some effort...some couple weeks for seperating all the components from the sheet.
![Album image #12 Album image #12](/albums/img/0/2/1/888021-10307-19-720.jpg)
The formed parts - and especially the fuselage - is extremely thin. I try to give a lot of support to make it stable and rigid.
![Album image #13 Album image #13](/albums/img/0/2/2/888022-10307-43-720.jpg)
Joining the wobbling edge seems a tricky exercise. Try to reduce the effort by support of wooden wedges.
![Album image #14 Album image #14](/albums/img/0/2/3/888023-10307-68-720.jpg)
Carving and sanding it in shape is done quick - compared to the plastic sanding of the last weeks 🙂
![Album image #15 Album image #15](/albums/img/0/4/6/888046-10307-31-720.jpg)
![Album image #16 Album image #16](/albums/img/0/2/4/888024-10307-11-720.jpg)
Some more ribs and frames to make the hull robust.
![Album image #17 Album image #17](/albums/img/6/0/4/888604-10307-48-720.jpg)
The front wheel comes in 2 halfes and they should be glued to the gear on 2 small surfaces - a butt joint I hardly trust. So a practicable joint to fix the gear strut and the tyre is not there - Therefore I drilled a hole here....
![Album image #18 Album image #18](/albums/img/6/0/5/888605-10307-36-720.jpg)
...and here. A brass tube will allow to join the wheel and the forward landing gear.
![Album image #19 Album image #19](/albums/img/6/0/6/888606-10307-39-720.jpg)
After trimming the axle the wheel should slip on easy and I expect that this front wheel assy is now more stable than before.
![Album image #20 Album image #20](/albums/img/4/0/1/890401-10307-42-pristine.jpg)
Details from a CASA 235 nose landing gear.
![Album image #21 Album image #21](/albums/img/4/0/2/890402-10307-28-720.jpg)
![Album image #22 Album image #22](/albums/img/4/0/3/890403-10307-18-720.jpg)
![Album image #23 Album image #23](/albums/img/4/0/4/890404-10307-96-720.jpg)
![Album image #24 Album image #24](/albums/img/4/0/5/890405-10307-27-720.jpg)
Scratched struts are on as well as forward lights.
![Album image #25 Album image #25](/albums/img/4/0/6/890406-10307-58-720.jpg)
Some wiring here...
![Album image #26 Album image #26](/albums/img/4/0/7/890407-10307-39-720.jpg)
...some wiring there.
![Album image #27 Album image #27](/albums/img/4/0/8/890408-10307-71-720.jpg)
mmh ... seems ok. Now let's see what we can do with the doors.
![Album image #28 Album image #28](/albums/img/2/8/9/894289-10307-13-720.jpg)
The part on the very right of the green sprue is the nose landing gear door. Having seen some reference pictures, I decided to go with the cut-away from the vacu sheet. The doors are usually sandwich composite parts. To imitate the "core -appearance" I will scratch them with styrene...
![Album image #29 Album image #29](/albums/img/2/9/0/894290-10307-48-720.jpg)
The real door hinges are goose-necked to support a quick opening by less movement of the strut - some remains from old PE will do....
![Album image #30 Album image #30](/albums/img/2/9/1/894291-10307-70-720.jpg)
My "composite doors" with hinges.....
![Album image #31 Album image #31](/albums/img/2/9/2/894292-10307-75-720.jpg)
...undergo some dry fit...
![Album image #32 Album image #32](/albums/img/2/9/3/894293-10307-54-720.jpg)
The arm lever for the opening mechanism on this CASA is pretty keen.
![Album image #33 Album image #33](/albums/img/2/9/4/894294-10307-83-720.jpg)
Another dry fit with actuator struts attached,...
![Album image #34 Album image #34](/albums/img/2/9/5/894295-10307-57-720.jpg)
Seems to work, position and angle are not quite right yet, but can be adjusted.
![Album image #35 Album image #35](/albums/img/2/9/6/894296-10307-30-720.jpg)
Precautions to avoid tailsitting. I put some lead in radom and cockpit.
![Album image #36 Album image #36](/albums/img/2/9/7/894297-10307-34-720.jpg)
The attachment of the tail cone is challenging. The thing is thin and wobbeling - but it should be rigid and strong as is should carry the vertical and horizontal stabilizers afterwards.
I hope this section is consolidated now with my balsa wood construction.
I hope this section is consolidated now with my balsa wood construction.
![Album image #37 Album image #37](/albums/img/2/9/8/894298-10307-51-720.jpg)
The idea was to add some guidance for the joints and to bring together the 2 halfes as consise as possible.
![Album image #38 Album image #38](/albums/img/2/9/9/894299-10307-18-720.jpg)
With that flush fitting it should work out pretty well (I hope.)
![Album image #39 Album image #39](/albums/img/3/0/0/894300-10307-25-720.jpg)
Next issue - fitting the horizontal fins. To support the joint and to assure the correct angle I built in an flat beam of wood.
![Album image #40 Album image #40](/albums/img/6/2/1/896621-10307-81-720.jpg)
I did the same on the vertical tail fin.
![Album image #41 Album image #41](/albums/img/6/2/2/896622-10307-83-720.jpg)
A view at the wooden "tail wing box".
![Album image #42 Album image #42](/albums/img/6/2/3/896623-10307-60-720.jpg)
Trial fit #999. I'm still quite doubtful that all this comes out well at the end...
![Album image #43 Album image #43](/albums/img/6/2/4/896624-10307-33-720.jpg)
The tail cone with all the rudders attached.....
![Album image #44 Album image #44](/albums/img/2/6/6/901266-10307-17-720.jpg)
2x Engine Cowling. I decided to open up the Air Intakes, the NACAs on both sides of the hoods and the Exhausts.
![Album image #45 Album image #45](/albums/img/2/6/7/901267-10307-16-720.jpg)
I used some styrene sheet to scratch the "channel" from the intake to the Engine.
![Album image #46 Album image #46](/albums/img/2/6/8/901268-10307-28-720.jpg)
Now it is better, because you can't no longer look through the cowling onto the naked Wing 😉
Also the NACAs are cutted "open" now.
Also the NACAs are cutted "open" now.
![Album image #47 Album image #47](/albums/img/2/6/9/901269-10307-50-720.jpg)
Opening the holes for the Exhaust.
![Album image #48 Album image #48](/albums/img/2/7/0/901270-10307-87-720.jpg)
...and inserting some bended thin metal sheet to creat my "new" exhausts.
![Album image #49 Album image #49](/albums/img/2/7/1/901271-10307-32-720.jpg)
![Album image #50 Album image #50](/albums/img/2/7/5/901275-10307-27-720.jpg)
![Album image #51 Album image #51](/albums/img/2/7/6/901276-10307-30-720.jpg)
And I did some re-scribing to pronouce the panel lines which are "gone" in the Vaccu forming process respectively by my sanding operations.
![Album image #52 Album image #52](/albums/img/2/7/4/901274-10307-25-720.jpg)
Another trial assembly showed that some more front-weight is needed before I close the fuselage halfs. So some more lead balls placed to avoid tailsitting.
![Album image #53 Album image #53](/albums/img/5/4/4/908544-10307-67-720.jpg)
Finally I have joint the two halfes of the fuselage and the tail section....
![Album image #54 Album image #54](/albums/img/5/4/2/908542-10307-24-720.jpg)
...alot of sprue goo and filler was needed to make a smooth transition of the joint.
![Album image #55 Album image #55](/albums/img/5/4/3/908543-10307-58-720.jpg)
The size and position of the doors do not match with the version I need. Interessing that they are correct in size but in a switched location.
![Album image #56 Album image #56](/albums/img/5/4/1/908541-10307-61-720.jpg)
Same with the windows,... I need 1 more and the whole pattern slightly shifted to the rear.
So all the engravings for doors and windows will be filled with liquide sprue and sanded over. ...I hate scribing but beside that, some panel lines are gone also and need to be recovered,...
So all the engravings for doors and windows will be filled with liquide sprue and sanded over. ...I hate scribing but beside that, some panel lines are gone also and need to be recovered,...
![Album image #57 Album image #57](/albums/img/3/7/5/919375-10307-81-720.jpg)
So here are some pic's of my scribing activities,....
![Album image #58 Album image #58](/albums/img/3/7/6/919376-10307-75-720.jpg)
Checking size respectively position of the cargo & pax doors,....
![Album image #59 Album image #59](/albums/img/3/7/7/919377-10307-69-720.jpg)
Scribing result on LH side......
![Album image #60 Album image #60](/albums/img/3/7/9/919379-10307-30-720.jpg)
...and also RH and underside done.
![Album image #61 Album image #61](/albums/img/3/8/0/919380-10307-53-720.jpg)
Here I have already fixed the vertical and horzontal stabilzers onto the fuselage.
![Album image #62 Album image #62](/albums/img/6/2/5/896625-10307-81-720.jpg)
The quality of the moulded parts is ...not the best. Some more sanding is needed to get those parts in shape.
![Album image #63 Album image #63](/albums/img/3/8/1/919381-10307-20-720.jpg)
Similar to the front landing gear I decided to "support" also the main landing gear with some metal tubes in order to hold the load of the entire kit without breaking wheels loose later on (there is pretty load of lead in the nose part).
![Album image #64 Album image #64](/albums/img/3/8/2/919382-10307-19-720.jpg)
Mainlanding gear ready for paint and assembly.
![Album image #65 Album image #65](/albums/img/8/3/9/923839-10307-91-720.jpg)
Painting and Assembly done.
![Album image #66 Album image #66](/albums/img/8/4/0/923840-10307-82-720.jpg)
Adjusting the landing gear within the bin is quite tricky. No marks or stops are given. A slight movement respectively a slight missmatch between left hand and right hand gear and the whole thing seems to come out of balance - as the span of the wings is intensifying any tiny misalignment. Leveled it out with ruler, blueTack and time...
![Album image #67 Album image #67](/albums/img/8/4/1/923841-10307-96-720.jpg)
Made my own stops and after several attempts I found it ok to use glue. Picture comparision showed later that the whole assembly should protrude slightly more - but too late now.
I started a time consuming masking session to protect the main landing gear from next coming (sanding) operations. 😉
I started a time consuming masking session to protect the main landing gear from next coming (sanding) operations. 😉
![Album image #68 Album image #68](/albums/img/3/3/9/942339-10307-77-720.jpg)
When closing the Wheel Bin alot of putty was needed in order to close rather huge gaps.
![Album image #69 Album image #69](/albums/img/3/4/0/942340-10307-76-720.jpg)
Bottom view after filling & sanding that area.
![Album image #70 Album image #70](/albums/img/3/4/1/942341-10307-60-720.jpg)
Side view after fitting the wheel bay to the fuselage.
![Album image #71 Album image #71](/albums/img/3/4/2/942342-10307-70-720.jpg)
Mounting the wing to the fuselage started....
![Album image #72 Album image #72](/albums/img/3/4/3/942343-10307-86-720.jpg)
Wooden stiffener for the upper wing middle section.
![Album image #73 Album image #73](/albums/img/3/4/4/942344-10307-66-720.jpg)
Liquide sprue and Tamyia putty as a gab filler used here and also for...
![Album image #74 Album image #74](/albums/img/3/4/5/942345-10307-46-720.jpg)
....adjusting the outer wing panels. Gravity, ruler and protractor are used to level out the wings during glueing and curing to get the sightly upwards position of the wing tips.
![Album image #75 Album image #75](/albums/img/6/1/5/972615-10307-74-720.jpg)
Now I have added the engines and the flap track fairings. Putting on some primer is coming closer,....
![Album image #76 Album image #76](/albums/img/7/3/2/987732-10307-25-720.jpg)
So the first layer of primer is there. Quite surprising - It looked not that bad.....
![Album image #77 Album image #77](/albums/img/7/3/3/987733-10307-26-720.jpg)
....there where only a few minor imperfections that need some filling/sanding and repaint.
![Album image #78 Album image #78](/albums/img/7/3/4/987734-10307-55-720.jpg)
I started with aircraft grey to bring some depth effect to the surface...
![Album image #79 Album image #79](/albums/img/7/3/5/987735-10307-42-720.jpg)
...more spraying...
![Album image #80 Album image #80](/albums/img/7/3/6/987736-10307-46-720.jpg)
...this is my third model where I try black basing/marbeling...quite tough to decide when it is enough...
![Album image #81 Album image #81](/albums/img/7/3/7/987737-10307-51-720.jpg)
A thin layer of blueish grey comes as a final coat.
![Album image #82 Album image #82](/albums/img/7/3/8/987738-10307-83-720.jpg)
The black anti-icing panels are next,...
![Album image #83 Album image #83](/albums/img/5/1/4/990514-10307-31-720.jpg)
Anti iceing panels and the underwing exhaust plume section done.
![Album image #84 Album image #84](/albums/img/5/1/5/990515-10307-53-720.jpg)
Unfortunatly I had a bad surface preperation and on the HTP the demasking caused some damage.
![Album image #85 Album image #85](/albums/img/5/1/6/990516-10307-38-720.jpg)
Starting the recovery....
![Album image #86 Album image #86](/albums/img/5/1/7/990517-10307-17-720.jpg)
Aircraft grey...
![Album image #87 Album image #87](/albums/img/5/1/8/990518-10307-29-720.jpg)
...plus some blueish grey on top.
![Album image #88 Album image #88](/albums/img/5/1/9/990519-10307-90-720.jpg)
Done. Gloss coat next and then ready for the decals,.....
![Album image #89 Album image #89](/albums/img/6/9/5/1005695-10307-69-720.jpg)
First session of decaling done...
![Album image #90 Album image #90](/albums/img/6/9/6/1005696-10307-72-720.jpg)
All decals on and sealed with a coat of gloss acrylics.
![Album image #91 Album image #91](/albums/img/6/9/7/1005697-10307-38-720.jpg)
After some days of gloss coat cure, I did a very decent oil wash, as the marbeling effect already shows a quite worne out surface.
![Album image #92 Album image #92](/albums/img/3/6/8/1021368-10307-97-720.jpg)
Giving the propeller blades a first layer of black.
![Album image #93 Album image #93](/albums/img/3/6/9/1021369-10307-26-720.jpg)
Preparing the antenna.
![Album image #94 Album image #94](/albums/img/3/7/0/1021370-10307-34-720.jpg)
The installed antenna on the RH side of the vertical fin.
![Album image #95 Album image #95](/albums/img/3/7/1/1021371-10307-91-720.jpg)
Nose landing gear and bay doors installed.
![Album image #96 Album image #96](/albums/img/3/7/2/1021372-10307-26-720.jpg)
Underwing section ist done - some minor touch-ups to cover painting flaws were needed
![Album image #97 Album image #97](/albums/img/7/3/6/1024736-10307-97-720.jpg)
Assembly of the propeller blades.
![Album image #98 Album image #98](/albums/img/7/3/7/1024737-10307-76-720.jpg)
Yeep. The last "unclued" components...Now...quite busy actually, but I think I need to finish this build this weekend. 🙂 😉
![Album image #99 Album image #99](/albums/img/5/4/4/1059544-10307-23-720.jpg)
![Album image #100 Album image #100](/albums/img/5/4/5/1059545-10307-38-720.jpg)
![Album image #101 Album image #101](/albums/img/5/4/6/1059546-10307-19-720.jpg)
![Album image #102 Album image #102](/albums/img/5/4/7/1059547-10307-73-720.jpg)
![Album image #103 Album image #103](/albums/img/5/4/8/1059548-10307-76-720.jpg)
![Album image #104 Album image #104](/albums/img/5/4/9/1059549-10307-84-720.jpg)
![Album image #105 Album image #105](/albums/img/5/5/0/1059550-10307-49-720.jpg)
![Album image #106 Album image #106](/albums/img/5/5/1/1059551-10307-88-720.jpg)
![Album image #107 Album image #107](/albums/img/5/5/2/1059552-10307-25-720.jpg)
![Album image #108 Album image #108](/albums/img/5/5/3/1059553-10307-92-720.jpg)
![Album image #109 Album image #109](/albums/img/5/5/4/1059554-10307-42-720.jpg)
![Album image #110 Album image #110](/albums/img/5/5/5/1059555-10307-73-720.jpg)
![Album image #111 Album image #111](/albums/img/5/5/6/1059556-10307-31-720.jpg)
![Album image #112 Album image #112](/albums/img/5/5/7/1059557-10307-68-720.jpg)
![Album image #113 Album image #113](/albums/img/5/5/8/1059558-10307-31-720.jpg)
![Album image #114 Album image #114](/albums/img/5/5/9/1059559-10307-23-720.jpg)
![Album image #115 Album image #115](/albums/img/5/6/0/1059560-10307-61-720.jpg)
![Album image #116 Album image #116](/albums/img/5/6/1/1059561-10307-98-720.jpg)
Komentáre
73 4 October 2020, 19:45
![](/profiles/img/10307-421-s.jpg)
Started my first vacu formed kit. Curious about this journey and what kind of pleasant surprises will wait. 🙂
4 October 2020, 20:05
![](/profiles/img/10307-421-s.jpg)
Ha -- 😄 crazy, but I thought at least I should have tried it once...Thx for your wished Mirko. I guess I need it.
5 December 2020, 15:03
![](/profiles/img/15888-619-s.jpg)
Loving this! I actually just finished my second vac. kit, also a Broplan. An ATR 72...Pictures on here somewhere
5 December 2020, 16:56
![](/profiles/img/46361-416-s.jpg)
looking good so far.Started a Wellesley couple of years back,horrible kit ,its in a box somewhere.LOL
5 December 2020, 17:10
![](/profiles/img/10307-421-s.jpg)
Chris - I just check out your ATR 72. Great result. Luckely I can skip interior work. But I see already troubles coming along with engine cowling and wheel bay - similar to your ATR kit. This portion of work will become pretty challenging.
5 December 2020, 20:17
![](/profiles/img/10307-421-s.jpg)
David - fingers crossed that this one will not end the same way - but the more I progress the more I understand why this happend 🙂
5 December 2020, 20:19
![](/profiles/img/10307-421-s.jpg)
Hi guys - thx for your coments and your "likes". That's good for staying motivated with this bird 😉
19 December 2020, 14:21
![](/profiles/img/10307-421-s.jpg)
@ Chris,
and all followers of this build - let me report: Engines done! 🙂 some pic's attached
26 December 2020, 20:42
![](/profiles/img/10307-421-s.jpg)
Sanding continues,....I have meanwhile joint the fuselage and rear section.
5 January 2021, 11:10
![](/profiles/img/15888-619-s.jpg)
Some major plastic surgery here! Brings back memories...
Looking good!
5 January 2021, 14:04
![](/profiles/img/10307-421-s.jpg)
Thank you Chris & Cuajete for your comments. Motivation on this kit is going up and down periodically 😉
So your appreciation is welcome! thx
7 January 2021, 16:59
![](/profiles/img/13136-468-s.jpg)
Great job, Juergen! Looks like a lot of sanding, but the fuselage looks good!
7 January 2021, 19:01
![](/profiles/img/10307-421-s.jpg)
Thx Gordon. YES: a lot of sanding, and I'm afraid that it is not over yet 😉
20 January 2021, 19:04
![](/profiles/img/10307-421-s.jpg)
a little bit of an update on this build - I joint tail and horzontal fins with the fuselage and did some scribing exercise.
20 January 2021, 19:06
![](/profiles/img/13641-502-s.jpg)
How come I missed this? My 295 is still waiting, let's see what awaits me 😄
20 January 2021, 19:49
![](/profiles/img/13641-502-s.jpg)
Have you considered filling the parts, so they get stiff? Like here:
Breguet Br. Bizerte | Album by potez452 (1:72)
21 January 2021, 15:49
![](/profiles/img/10307-421-s.jpg)
and...OMG! potez452's documation is great.
and...YES. I thought about filling them. But I was not sure what material will make it stiff but not too heavy. As my Tamiya putty was eating away the styrene in the areas where i used it to support the bulkheads that I put into my craft ...I gave up this idea. I will check what potez452 use, may quite useful for the wings...THANKS
21 January 2021, 20:30
![](/profiles/img/10307-421-s.jpg)
Was able to work a bit on the landing gears. Don't ask me details,...... 🙁
26 January 2021, 19:45
![](/profiles/img/13641-502-s.jpg)
Looks brilliant, remember this is Broplan, even worse than A-Model😉
26 January 2021, 20:53
![](/profiles/img/46361-416-s.jpg)
Had a similar problem with pz2 LuchsI made a jig to put on the chassis to level everything up when I glued suspension arms on.
29 January 2021, 14:55
![](/profiles/img/10307-421-s.jpg)
@Lukasz:
wingspan 35,5[cm]
lenght 29[cm]
beside my PBY Catalina build (modellversium.de/gal..atalina-academy.html) this one is the biggest plane in my collection by now (I am mainly in 72 scale).
But an C130 Hercules & a Dornier JII Wal is in my stash too.
23 February 2021, 20:19
![](/profiles/img/10307-421-s.jpg)
thx Lukasz & David. I am ready for a layer of primer now. I'm curios how this "treated" surface with all the putty, sanding, etc,....turns out then. Pic's will follow asap.
24 April 2021, 20:15
![](/profiles/img/13641-502-s.jpg)
Congrats on the tail recovery. It keeps looking better with each update. 👍
2 May 2021, 07:43
![](/profiles/img/10307-421-s.jpg)
Hi guys - Some minor progress to be reported....all decals on and sealed now. A lifgt oil wash applied too. Looking forward to find the time to dim the surface down and to add the last pits & pieces.
22 May 2021, 19:49
![](/profiles/img/10307-421-s.jpg)
As summer time is slowing down my build process it took some time to post a new status. Now I added some pictures of detailing work which I have done the last few weeks. I see the finish line come close.
24 June 2021, 08:18
![](/profiles/img/74389-420-s.jpg)
Incredible work done so far - truly remarkable dedication and effort that you put into this near tabula rasa of a kit! Very much looking forward to the finish! 👍👍👍
26 June 2021, 15:59
![](/profiles/img/10307-421-s.jpg)
Finally - Done with my first vaccuform experiment. The Casa CN-235 was finished in July, but was not able to take some pictures. Now - here they are....
cheers
29 August 2021, 20:09
![](/profiles/img/13641-502-s.jpg)
Oh man, this is exquisite 👍 love the cockpit decal - the hand reminds me the "Titanic" movie 😉
29 August 2021, 20:11
![](/profiles/img/14143-361-s.jpg)
Dir gebührt eine Medaille alleine für die Tatsache, dass du in der heutigen von 3D-Hitec & Co dominierten Modellbau Welt einen Vacu baust!!
30 August 2021, 05:28
![](/profiles/img/11836-205-s.jpg)
Absolutely great result Jürgen! 👍 Looking forward to see it live in Ried! 😉
30 August 2021, 07:00
![](/profiles/img/27826-126-s.jpg)
Fantastic result and better job.
I hope that some brand release the CN-235 in plastic.
Congrats!
30 August 2021, 19:37
![](/profiles/img/10307-421-s.jpg)
Hi @all - many thanks for your kind words. It was fun to make experience with vaccu technique. Not sure if this was my first & last attempt....
@Dietmar & Harry - The bird will be there and I am looking forward for the exhibition too. After the Covid break it will be good to meet some mates and checking how productive they have been in the last 2 years. Hope the current figures will not spoil it at the end. Fingers crossed.
30 August 2021, 20:25
![](/profiles/img/10307-421-s.jpg)
Thx Alexander - Vaccu was a challenge, but interessing and from a distance fun too.
26 October 2021, 15:58
![](/profiles/img/user-s.jpg)
Hard to believe that this once was a vacu-kit. Just to brave such a task deserves respect. I bow my hat for the incredible result.
28 October 2021, 15:20
![](/profiles/img/12448-935-s.jpg)
This looks stunning. And you make it look so easy. I've got this kit to do an Irish Air Corps one, was going to start it this weekend. Not so sure now!
18 February 2022, 22:43
![](/profiles/img/10307-421-s.jpg)
Thank you Roy for your nice comments. And I hope you have started the kit. It's alot of work and effort, but it is worth it - you will have a very rare model on the shelf then,....let us know how it turn out! cheers
21 February 2022, 13:19
![](/profiles/img/34728-244-s.jpg)
What a nice tutorial ! And what a result !!!
I own a few vaccu kits which I never dared tackle. Maybe now I shall...
21 February 2022, 16:11
Album info
VACU_FORM !