Најважније вести

Bozzer
Blimey Steph, that paint job drew me to it, while I was scrolling through the newsfeed! Excellent work, mate 👍

Nicolas
Following

Stéphane Jayet
Thank you Bozzer

George Williams
Neat work not sure about that blue though.

Emanuele Matteucci
I did a good job on this paintjob too, it's not easy and you did very well! I hope for you that the final assembly of your model is better than mine was. Because i trashed the entire car when i saw the gap between the main body and the under chassis. I tried my best to made them fit togheter but it looked like the pieces came from 2 different car models...Untill now the most disappointing model i tried to complete, I wish you the best for the remaining job, the subject is fantastic!

Stéphane Jayet
@George, light makes it appear lighter than reality but I think you are right and bit too moght

Stéphane Jayet
@Emanuele, I will cross fingers now not to have the same problem as you.

Martin Oostrom
Striking colours!

Ricard Gomicia Calatayud
brutal job on the cockpit!

Stéphane Jayet
Thank you Ricard

Bozzer
Damn, you got me again!
This build is reaching EPIC status!
Excellent work, Steph 👍

Stéphane Jayet
Thank you Bozzer

George Williams
Looking good from where I'm sitting.

Moreno Baruffini
Watching with interest!

Jan Janssen
#me too, wondering how it builds-up

Jan Peters
Pulling up a chair

Cuajete
Thomas, I knew you were going to get this kit! 🙂

I was hesitating a lot between the Swedish box and the Jordanian box. It took me a long time to decide, but in the end I ordered the Jordanian one because I already have several future projects with that fantastic Swedish scheme.

I follow you with great interest (as always). It is quite possible that I will finally regret choosing the Jordanian box 😉

Łukasz Gliński
Been waiting for this one 👍Utterly cool camo indeed

Harry Eder
Watching! 👍 Good luck with the kit...

Thomas Kolb
Did some dry-fitting yesterday, and just as I expected by the looks of it, it is definitely A-model quality. A lot of fettling, scraping and sanding is required for a decent fit of the major parts such as the fuselage halves and the wings. Good thing it is a small model!

Erik De Smet
It seems that it is of the same "quality" as their SF260 and Alpha jet kits. Have you ever built the venerable Airfix kit ?

Michael Kohl
I will watch too how you turn this ugly duck into a beautiful swan.

Thomas Kolb
Erik, I actually think that this is a retooling of the Airfix kit. Slightly different parts and recessed panel lines, but the breakdown is almost identical.

Łukasz Gliński
Looks like AZ Model is morphing into A-Model 😛

Daniel Mysak
I´m following. Looks like a bunch of work to get a proper model out of this kit. I'm sure you will handle it.

Finn
Will follow

Thomas Espe
👀

Cuajete
I think KP/AZ should start an improvement their molds after so many kit releases and sales, as Special Hobby has already successfully done. It is curious that for some kits they make good molds (such as the Bf-109) and for others they are so mediocre.

Despite this, I am sure that Thomas will do an extraordinary job 👍

Matthew A
🍿

Cuajete
Interiors looks great, Thomas 👍

Robert Podkoński
I am a little late, but from now I will follow with pleasure and interest (like all Thomas's previous builds 😉 )

Guy Rump
Looking good 👍

Tom B.
Looks like a lot of craftsmanship will go into this kit before the end of the build... Curiously following 👍

Thomas Kolb
This little kit is definitely putting up a fight in every step. Silly me, I thought this was going to be a relaxed weekend project, ha ha. 🙂

Łukasz Gliński
I know that feeling, it usually ends up this way 😉

Cuajete
Łukasz enjoys with suffered models 😛
Good (hard) job so far, Thomas 👍

Erik De Smet
KP short run = long work. I prefer Vallejo putty for filling seams on this type of kits, as it comes with a fine tip

Thomas Kolb
Erik yes, I think the photo shows a bit of my frustration with the seam lines. It should not be like this for a 2022 tooling.

Cuajete
Thomas, will the skinny front landing gear hold the weight of all those fishing weights?

Łukasz Gliński
Wow, how did you squeeze all that lead inside 😮

Thomas Kolb
Well, those weights are juuuust barely enough to keep the Bulldog on its nose gear and still kind of pivots around its main gear. Good thing that the entire engine compartment behind the dashboard is empty so with some Tetris skills you can fill it completely with those fishing weights.

Erik De Smet
So the front wheel does not support any weight, as the nose is in balance with the tail. I had the same problem with KPs SIAI Marchetti, and the SH Marchetti needs also quite some weight in the nose.

Michael Kohl
not a shake an bake-kit for sure. I like how you tackle it. For maximum usage of weight in tight spaces consider lead granules. They come rather cheap by the kilogram and have a diameter of max 1 - 2 mm. You can even drill a hole into the fuselage after it is closed and pour the granules in - followed by some white glue to fix them.

Thomas Kolb
After having lingered in the limbo state of half-finished projects, I have decided to reboot this build. The screwed up paintjob was removed with IPA alcohol and the model is now back to bare plastic. Some correcting fills are done and it is soon time to reapply the primer. I will make my life easier this time and just build the standard Swedish Air Force version. But I have already purchased a second kit to be finished with the Swedish Army splinter camouflage as I think I know this time how to do it properly. Stay tuned!

J35J
Great to see that you have restarted the kit. The weight distribution is a real pain. Had similar challenges with my Airfix SK61 build some months ago, Liquid Gravity sorted the issue.
SwAF livery will look aces. Keep up the spirit!👏🏼👍🏻

Michael Kohl
No idea what that livery will look like, but nice that this one is back at the bench. Reminds me of my Safir which is at a similar state.

Moreno Baruffini
Glad to see this kit again on the bench! ,👍🏻👍🏻👍🏻

Mid Franconian
🧑‍💻 Interesting as always!

Cuajete
Thomas, It's fantastic to read that you are taking up this project again. Great!

Ekki
And watching it.

István Szücs
Well documented build, great work, as usual!

Łukasz Gliński
Great to see you back with this little fella 👍

gorby
Thanks Matthew - number 16 is my fave. 😄