Најважније вести

Steffen
Hallo Thomas, ja, die sind noch da!
Hättest du sonst noch an etwas aus meinem Stash Interesse?
Gruß, Steffen

Thomas Neuss
Hi - die beiden Sachen sind dann alles. Ich komme mir selber etwas dämlich vor, dass ich das übersehen habe, als ich die Mosquito angefragt habe... seufz. Jetzt bin ich alles durchgegangen. Viele Grüße, Thomas

Steffen
Hi Thomas, damit ich das Porto bestimmen kann, muss ich wissen, wo du wohnst. Wäre PayPal ok? Gruß, Steffen

Thomas Neuss
Hallo,
der Versand wäre in Deutschland, hier schon mal meine Adresse:
Thomas Neuss
Wilhelm-Leuschner-Weg 5
25524 Itzehoe
PayPal (Freunde) ist völlig ok für mich.
Viele gRüße
Thomas

Thomas Neuss
Hi Steffen,
das wären dann 13.- für die Control Surfaces und 10.- für die Exhaust Shrouds + Porto, richtig?
Viele Grüße
Thomas

Steffen
Ganz genau! Das sollte als Großbrief für 1,60 EUR gehen.
Mein PayPal: steffen.kunze@posteo.de

Thomas Neuss
Prima - ich habe Dir per PayPal das Geld gesendet.
Viele Grüße und schon mal vielen Dank 🙂
Thomas

Steffen
Super, danke, kam an! Ich bin morgen wieder zu Hause und melde mich, sobald ich versendet habe. Gruß, Steffen

Thomas Neuss
Prima - eilt nicht, ich bin ab Mittwoch ohnehin 10 Tage unterwegs... 🙂

Steffen
Brief ist fertig, muss ihn nur noch abgeben

Steffen
Der Brief ist unterwegs

Thomas Neuss
Vielen Dank 🙂 und viele Grüße

Steffen
Angekommen?

Thomas Neuss
Hi - bin heute wieder nach Hause gekommen und ja, sie sind gut angekommen 🙂
Vielen Dank und viele Grüße
Thomas

Steffen
Super, viel Spaß damit!

Sy Bar
Was going to do the Battle of Britain version of this kit but I'm temped to have a go at some winter white wash and the wasp is cooler than the shark mouth 😎

Nicolas
Following

István Szücs
I also have Bf-110 from the Airfix, I will build an Italian night fighter. The sprues are the same, so I'm watching!

Sy Bar
Cheers guys.
I'm have a go at riveting, but going freehand as at this scale using tape was taking so long. I also not sure how much they will stand out on finish kit, but with the wonky line in parts they will probably bee seen from mars 🤣

Mark Sherwood
Looking good so far, like the underside. 🥸👍

Sy Bar
Cheers #Mark

Skyhiker
Sy, how was the fit on this kit?

Guy Rump
Looking good, following. 👍

Sy Bar
Cheers #Guy 👍
#Skyhiker I found the fit to be good, I had a very slight gap at the front but think that was as much to do with me and the fitting of the pit (not the clearest instructions there). Every thing else was fine and the canopy was a good fit, I did change order of build slightly with the tail section I glued the rear piece to the body first then added the tail (after I'd added the stabilisers/rudders) this made more sense than the instructions 😁

Sy Bar
Only issue I have with this kit are the decals. While they look great and are in perfect register, they have a large amount of film edging and are both thick and delicate at the same time🤪
Having a hard time getting them to settle into the panel lines etc. I usually just need to use micro sol but even ultimate extra strong is not have much effect. Going to have to wait till I get some Tamiya fixer, strong and extra strong hopefully one of these will help 🤞

Mr D
You should be ok with the medium one with Airfix decals,
I like a mix of Water in with the markfix...seems to keep the decal floating longer.
I did the teeth on my p40 this way.
If they started getting bit sicky...l would add bit more water....keep it floating.
Wouldn't like to do shark teeth with HB decals 🤔🤣.... The lightning ⚡ strike on my mig-15 just fell apart with hardly any working.
Good luck with it ..look forward to seeing 😃👍👍

Dave Flitton
Looking good!

Sy Bar
Cheers for advice #Mr D. Afraid this set of decals were unaffected by all solutions but the mark fit super strong did have some effect. To make head way I found I needed to add the solution then after a few seconds apply hot air from a hairdryer to 'shrink wrap' the decal. These have to be the worst decals I've come across..
I recommend anyone doing this kit to source a set of decals rather than use those provided, they are not for beginners that's for sure. I hope the carrier film will disappear under a gloss coat but I didn't want to risk it so I've only applied the larger decals the smaller ones while add great detail if cartograf here they are 90% carrier film.

Skyhiker
Why don't you just cut the carrier film away with a knife before applying them?

Mr D
Hi Sy
That's ok .... I think the result will be fine after a clear coat, you come out of it without wrinkles, bubbles or tear's so it's a win, very smart n be sorted under a clear.👌👍👍

Sy Bar
Cheers #Mr D
#Skyhiker that's idea but life's too short for the amount there is, the size of the decal that's left will look like small black dots everywhere (especially the fuselage rib numbers 🤪); would be ok in 48 but too much in 72. Also I'm probably going to much it all up when I apply the winter white wash 😆