WIP RF-4C
![Album image #1 Album image #1](/albums/img/2/6/8/1666268-25429-40-720.jpg)
So, the FineMolds spine insert has some wiggle room and doesn’t fit as snug as I would like. I found out that certain types of fine deli come with very thin sheets of styrene in between the deli cuts (Schwarzwalder schinken) that fit right into the tiny gaps.
![Album image #2 Album image #2](/albums/img/2/6/9/1666269-25429-19-720.jpg)
It’s a bear to line them up but with enough patience one can make it work. I used Ammo Red Magma cement because it evaporates before melting the sheets into mush and to see what I’m doing.
![Album image #3 Album image #3](/albums/img/2/7/0/1666270-25429-11-720.jpg)
Trimming away the excess to see how it worked.
![Album image #4 Album image #4](/albums/img/3/1/5/1666315-25429-42-720.jpg)
Note to self: don’t use scissors as they gauge the plastic…. Other than that, the gap is dressed up nicely! 👍
![Album image #5 Album image #5](/albums/img/9/3/6/1670936-25429-39-720.jpg)
Spot primed the spine and the new panel lines show up nicely
![Album image #6 Album image #6](/albums/img/9/3/7/1670937-25429-82-720.jpg)
Some dressing up on this side but generally I’m really content!
Коментари
16 18 February, 00:58
![](/profiles/img/111789-903-s.jpg)
Nice trick... do you at least think it smells still like Schinken? 😉
Following! 🙂
25 February, 13:13
![](/profiles/img/72020-938-s.jpg)
Nice start, patience and skills, like always needed, applied here 🙂. Please tell us what you think of the Kelik cockpit when you get there.
25 February, 22:03
![](/profiles/img/25429-812-s.png)
Hi Mark! Thanks! I'll post pictures and will address my findings when I get there for sure. 👍🏼
25 February, 22:10
![](/profiles/img/17422-305-s.jpg)
Patrick, I have a question. How come are you using two kits? Doesn't the Hasegawa have all the bits and pieces for a RF-4C? I went through a quick look on my Hasegawa (the same you have) and it contains the exhaust cans and other things.
26 February, 11:36
![](/profiles/img/25429-812-s.png)
And a good question it is, Maciej! 🙂 I really like the details and fit of this new FineMolds kit compared to the 30 year old Hasegawa kit. The Hasegawa kit in its own right is a beautiful kit but I wanted to see if I could combine the fine details of the FineMolds kit to the RF-4 front fuselage. Even though I'm dressing up the spine insert, this spine insert is lightyears ahead of the Hasegawa split fuselage. Irony would have it that when I finish this Phrankenphantom, FineMolds will issue a true RF-4C. 😉
26 February, 22:13
![](/profiles/img/17422-305-s.jpg)
Thanks, indeed the Finemolds is a gem. I suppose you will be building a F-4C/D out of the Hasegawa kit, or even an F-4J/S is possible provided you have the proper decals.
26 February, 22:21
![](/profiles/img/25429-812-s.png)
As far as I can see the parting lines between the front and rear fuselages are at the exact same panel lines, so I could cobble the 'remaining' parts together. I could go for an F-4C/D as the FineMolds from fuselage is the Air Force variant. I think I have some decals for that in my spares box.
26 February, 22:32