Зид
Wall
October 14, 2024
October 13, 2024
October 9, 2024
October 4, 2024
October 3, 2024
October 2, 2024
September 30, 2024
September 27, 2024
September 24, 2024
September 19, 2024
September 18, 2024
September 16, 2024
September 14, 2024
September 13, 2024
September 5, 2024
September 4, 2024
September 2, 2024
August 31, 2024
August 30, 2024
August 28, 2024
August 26, 2024
August 19, 2024
Ryan
жели овај предмет
жели овај предмет
P-47D Thunderbolt "Bubbletop" & 1/4-ton 4x4 Light Vehicle Set
Tamiya 1:48
25214 2023 Модел сет Мултитема (2)19 August, 19:39
August 17, 2024
August 13, 2024
August 10, 2024
August 7, 2024
August 1, 2024
Ryan
жели овај предмет
жели овај предмет
P-47D Thunderbolt "Bubbletop" & 1/4-ton 4x4 Light Vehicle Set
Tamiya 1:48
25214 2023 Модел сет Мултитема (2)1 August, 16:44
July 31, 2024
July 28, 2024
July 27, 2024
July 20, 2024
July 19, 2024
July 17, 2024
July 15, 2024
July 14, 2024
July 8, 2024
July 6, 2024
July 4, 2024
June 29, 2024
June 23, 2024
Ryan
додао је нови фотоалбум.
додао је нови фотоалбум.
11 22 June, 23:46
Casey Beckett
Hey - cool shot - never knew the bird has triple wheel sets. And Congratulations for a rare Anigrand build.
Hey - cool shot - never knew the bird has triple wheel sets. And Congratulations for a rare Anigrand build.
22 June, 23:58
Treehugger
If you want to try using putty but don't like Tamiya's imo obnoxious toxic putty, I can recommend Vallejos white putty. Just take into account that the putty will shrink, the more is applied. A trick to avoid putty shrinking, is to fill more putty into a hole than required, so the putty stands out like an ice cream cone or something, then wait to let it dry, then cut off the excess putty with a blade, then sand smooth. Sometimes you will want to be careful applying putty, using masking tape, else you risk there is too much putty that goes hard and is harder to remove again, so you could just put some putty on a finger tip, and wipe the putty across some small gap and quickly use a moist cotton bud to clean up the excess putty around the cavity.
If you want to try using putty but don't like Tamiya's imo obnoxious toxic putty, I can recommend Vallejos white putty. Just take into account that the putty will shrink, the more is applied. A trick to avoid putty shrinking, is to fill more putty into a hole than required, so the putty stands out like an ice cream cone or something, then wait to let it dry, then cut off the excess putty with a blade, then sand smooth. Sometimes you will want to be careful applying putty, using masking tape, else you risk there is too much putty that goes hard and is harder to remove again, so you could just put some putty on a finger tip, and wipe the putty across some small gap and quickly use a moist cotton bud to clean up the excess putty around the cavity.
23 June, 07:30
Casey Beckett
Deluxe Materials Perfect Plastic Putty is my go to - don't care for the Tamiya stuff either -
Perfect Plastic Putty (Deluxe Materials BD44, No)
Deluxe Materials Perfect Plastic Putty is my go to - don't care for the Tamiya stuff either -
Perfect Plastic Putty (Deluxe Materials BD44, No)
23 June, 19:44
June 22, 2024
June 19, 2024
June 17, 2024
June 13, 2024
June 11, 2024
June 6, 2024
Ryan
довршили ову ставку
довршили ову ставку
Boeing C-17B Advanced Globemaster III
Anigrand Craftswork 1:144
AA-4005 6 June, 16:28
June 5, 2024
June 4, 2024
Ryan
will attend
will attend
OMS Model Kit Swap Meet in Portland, Oregon
Portland, Oregon
29. Јун 2024
29. Јун 2024
4 June, 17:47
June 3, 2024
wnolder.php?lang=sr
2024-06-03 18:28:44
2024-02-05 20:47:35
138770
/ajax/wnolder.php?lang=sr&sd=2024-06-03 18:28:44&md=2024-02-05 20:47:35&filter=&w=138770
todo