BAC TSR.2 (Airfix)
![Album image #1 Album image #1](/albums/img/1/7/0/425170-10105-39-pristine.jpg)
Let's build this baby - but not with the lady jockeys. I'd like a proper TSR.2.
![Album image #2 Album image #2](/albums/img/1/7/1/425171-10105-55-720.jpg)
Seriously nice undercarriage resin from CMK. I think they sell this by the kilogram.
![Album image #3 Album image #3](/albums/img/1/7/2/425172-10105-96-720.jpg)
And a beautiful interior set as well. Only one vac canopy, though. If I use it, I only have once chance to cut it out.
![Album image #4 Album image #4](/albums/img/1/7/3/425173-10105-22-720.jpg)
And resin for the intakes and exhaust. The FOD covers are really nice, but they will hide some detail. But the kit does not have seamless intakes, so we'll see.
![Album image #5 Album image #5](/albums/img/1/7/4/425174-10105-61-720.jpg)
Resin control surfaces, including the entire tailplane/elevator parts. Very nice indeed.
![Album image #6 Album image #6](/albums/img/1/7/5/425175-10105-85-720.jpg)
And some resin to put in the bomb bay to represent some of the test equipment.
![Album image #7 Album image #7](/albums/img/1/7/6/425176-10105-37-pristine.jpg)
I also have this photoetch set from Eduard, but to be honest I don't think much of it is necessary.
![Album image #8 Album image #8](/albums/img/1/7/7/425177-10105-67-720.jpg)
A significant improvement in detail from the kit cockpit.
![Album image #9 Album image #9](/albums/img/1/7/8/425178-10105-74-720.jpg)
Time to start - let's remove the avionics panel.
![Album image #10 Album image #10](/albums/img/1/8/0/425180-10105-51-720.jpg)
Yikes! It looks like Stratos 4 took a direct meteor hit.
![Album image #11 Album image #11](/albums/img/1/8/4/425184-10105-93-720.jpg)
Final shaping with sandling sticks. I followed the panel lines, and the opening is just a tad bit larger than the resin part.
![Album image #12 Album image #12](/albums/img/1/8/3/425183-10105-66-720.jpg)
All the locating tabs for the kit cockpit have to be removed.
![Album image #13 Album image #13](/albums/img/1/8/6/425186-10105-36-720.jpg)
And then the cockpit will fit OK. I also did a bit of sanding and shaping to the resin cockpit part.
![Album image #14 Album image #14](/albums/img/1/8/1/425181-10105-28-720.jpg)
The entire pour block must be removed from the resin part, so get out the razor saw.
![Album image #15 Album image #15](/albums/img/1/8/2/425182-10105-23-720.jpg)
Nice clean cut on the avionics bay.
![Album image #16 Album image #16](/albums/img/1/8/5/425185-10105-54-720.jpg)
Test fitting the bomb bay and wheel wells - some reports on the web indicate shrinkage on this part, but mine seems to fit well.
![Album image #17 Album image #17](/albums/img/1/8/7/425187-10105-87-720.jpg)
I had to use some strip styrene to make the opening the same dimensions as the avionics bay.
![Album image #18 Album image #18](/albums/img/1/8/8/425188-10105-58-720.jpg)
The nose gear and avionics bay have some minor interference at the bottom. A little bit of sanding and all is well.
![Album image #19 Album image #19](/albums/img/1/8/9/425189-10105-76-720.jpg)
More test fitting - the nose gear bay is also a bit nicer than the kit part.
![Album image #20 Album image #20](/albums/img/1/9/0/425190-10105-65-720.jpg)
Making sure the avionics bay doesn't interfere with the cockpit - no problem!
![Album image #21 Album image #21](/albums/img/0/8/5/426085-10105-96-720.jpg)
CMK seats with Eduard harnesses. The metallic green tubes will disappear once the seats are installed!
![Album image #22 Album image #22](/albums/img/0/8/4/426084-10105-50-720.jpg)
Instrument panels are resin, photoetch, and many tiny decals cut up and positioned. Litres of solvent.
![Album image #23 Album image #23](/albums/img/0/8/3/426083-10105-86-720.jpg)
All cockpit components got a Future wash to bring out details.
![Album image #24 Album image #24](/albums/img/0/8/2/426082-10105-88-720.jpg)
I'm kinda liking it.
![Album image #25 Album image #25](/albums/img/2/2/6/426226-10105-90-720.jpg)
Hmm...these are going to need some work.
![Album image #26 Album image #26](/albums/img/3/2/5/428325-10105-11-720.jpg)
The intake blends from a circular shape into the more square fuselage section.
![Album image #27 Album image #27](/albums/img/3/2/7/428327-10105-88-720.jpg)
A small resin repair underway - I got a bit too zealous with the sanding stick!
![Album image #28 Album image #28](/albums/img/3/1/8/428318-10105-33-720.jpg)
Should not be a gap under the intake cone.
![Album image #29 Album image #29](/albums/img/3/2/0/428320-10105-11-720.jpg)
A little styrene can fix that...
![Album image #30 Album image #30](/albums/img/3/1/9/428319-10105-71-720.jpg)
This works nicely, and provides an additional surface for a stronger bond.
![Album image #31 Album image #31](/albums/img/3/2/2/428322-10105-53-720.jpg)
The photoetch flame holder from Eduard fits perfectly with the CMK exhaust pieces.
![Album image #32 Album image #32](/albums/img/3/2/1/428321-10105-36-720.jpg)
The cut-outs for the airbrakes need to be modified to accept the resin parts.
![Album image #33 Album image #33](/albums/img/3/2/3/428323-10105-42-720.jpg)
A little tweaking and sanding and they fit nicely. CMK provide the shaft that connects the actuator to the central drive.
![Album image #34 Album image #34](/albums/img/3/2/4/428324-10105-51-720.jpg)
All special equipment used for flight test purposes were painted orange.
![Album image #35 Album image #35](/albums/img/3/2/6/428326-10105-33-720.jpg)
The front of this piece (which goes in front of the wing) also needs to blend in smoothly with the intakes.
![Album image #36 Album image #36](/albums/img/3/6/4/429364-10105-73-720.jpg)
Drilled out the two vents on top of the intakes. These still need to be shaped, as they weren't round in real life.
![Album image #37 Album image #37](/albums/img/3/6/5/429365-10105-47-720.jpg)
Navigator's instrument panel protrudes too much into the cockpit, needs to be fixed.
![Album image #38 Album image #38](/albums/img/3/6/6/429366-10105-37-720.jpg)
This is more like it! Fuselage has been closed up.
![Album image #39 Album image #39](/albums/img/3/6/7/429367-10105-65-720.jpg)
Starting to bear some resemblance to the real TSR.2.
![Album image #40 Album image #40](/albums/img/3/6/8/429368-10105-61-720.jpg)
Resin parts for the cockpit sidewalls were also added.
![Album image #41 Album image #41](/albums/img/3/6/9/429369-10105-71-720.jpg)
I don't trust this seam, so I reinforced from underneath with sheet stryene.
![Album image #42 Album image #42](/albums/img/5/7/1/429571-10105-75-720.jpg)
The lower wing needs some surgery to prepare for the resin flaps.
![Album image #43 Album image #43](/albums/img/5/7/2/429572-10105-25-720.jpg)
I hope this is the right place to cut!!
![Album image #44 Album image #44](/albums/img/5/7/3/429573-10105-73-720.jpg)
The new resin pieces with attach like this.
![Album image #45 Album image #45](/albums/img/5/7/0/429570-10105-11-720.jpg)
Next, the top wing needs to have the flaps cut out.
![Album image #46 Album image #46](/albums/img/5/7/5/429575-10105-17-720.jpg)
The new resin flaps will fit nicely between the upper wing and the resin portion of the lower wing, with the actuator fairings overlapping.
![Album image #47 Album image #47](/albums/img/5/7/4/429574-10105-10-720.jpg)
I added a spreader to set the width of the rear fuselage, and to add some strength.
![Album image #48 Album image #48](/albums/img/0/0/0/430000-10105-17-720.jpg)
Another spreader added up near the intakes.
![Album image #49 Album image #49](/albums/img/0/0/1/430001-10105-68-720.jpg)
The wings and remaining two top fuselage pieces were joined to make sure the seams aligned properly.
![Album image #50 Album image #50](/albums/img/0/0/2/430002-10105-32-720.jpg)
Surprisingly, this fits on the fuselage quite nicely.
![Album image #51 Album image #51](/albums/img/5/4/8/430548-10105-66-720.jpg)
Hacking out the lower airbrake to make room for the resin.
![Album image #52 Album image #52](/albums/img/5/4/6/430546-10105-10-720.jpg)
Fits well, just need to add some styrene to go between the airbrake door hinge arms.
![Album image #53 Album image #53](/albums/img/5/4/7/430547-10105-63-720.jpg)
The kit's main gear legs need to have a notch removed to clear the orange box as shown.
![Album image #54 Album image #54](/albums/img/5/5/0/430550-10105-79-720.jpg)
The famous Airfix "splay angle" error. This should be 36° - but the legs have some play in their mount...
![Album image #55 Album image #55](/albums/img/5/4/9/430549-10105-85-720.jpg)
Squeeze them together at their base, and we have 38° which is probably close enough!
![Album image #56 Album image #56](/albums/img/3/9/7/431397-10105-40-720.jpg)
We'll need some more filler here! But it's not as bad as I expected.
![Album image #57 Album image #57](/albums/img/1/3/9/435139-10105-31-720.jpg)
Better, but still needs some additional work.
![Album image #58 Album image #58](/albums/img/1/4/0/435140-10105-97-720.jpg)
Added the section of fuselage that is between the airbrake hinges. This area was removed when I cut out the area for the brake bays.
![Album image #59 Album image #59](/albums/img/1/4/1/435141-10105-87-720.jpg)
The template is exactly 36 degrees, the correct splay angle of 18 degrees per side.
![Album image #60 Album image #60](/albums/img/1/4/2/435142-10105-19-720.jpg)
I added some small pieces of styrene to hide some gaps that will appear when the gear/bomb bay is added.
![Album image #61 Album image #61](/albums/img/1/4/3/435143-10105-94-720.jpg)
Here is one at the front of the bomb bay - it corrects for the resin being a bit short.
![Album image #62 Album image #62](/albums/img/1/4/4/435144-10105-14-720.jpg)
And one at the back of the bomb bay.
![Album image #63 Album image #63](/albums/img/1/4/5/435145-10105-11-720.jpg)
Fuselage is closed up.
![Album image #64 Album image #64](/albums/img/1/4/6/435146-10105-68-720.jpg)
Starting to look more like a TSR.2!
![Album image #65 Album image #65](/albums/img/1/4/7/435147-10105-25-720.jpg)
The empannage and exhausts need to be added.
![Album image #66 Album image #66](/albums/img/1/4/8/435148-10105-20-720.jpg)
No gaps! My little pieces of styrene did a good job.
![Album image #67 Album image #67](/albums/img/1/4/9/435149-10105-14-720.jpg)
There are a lot of hydraulic lines that are quite prominent in the gear bays - ugh. Will need to be added.
![Album image #68 Album image #68](/albums/img/1/5/0/435150-10105-93-720.jpg)
Many brake lines on the main gear strut, too. Double ugh.
![Album image #69 Album image #69](/albums/img/1/5/1/435151-10105-14-720.jpg)
Retraction struts need to be added to the nose gear. Airfix do not supply them.
![Album image #70 Album image #70](/albums/img/2/3/8/442238-10105-20-720.jpg)
Photoetch flame holders in the exhausts.
![Album image #71 Album image #71](/albums/img/2/3/6/442236-10105-79-720.jpg)
Empennage attached to the rear fuselage.
![Album image #72 Album image #72](/albums/img/2/3/7/442237-10105-27-720.jpg)
I decided to change the colour of the wheel wells and gear struts to the lighter grey on the left.
![Album image #73 Album image #73](/albums/img/2/4/0/442240-10105-13-720.jpg)
The front instrument panel cooming is added. No HUD glass on the TSR.2.
![Album image #74 Album image #74](/albums/img/2/4/1/442241-10105-82-720.jpg)
Vacuform windscreen doesn't fit so well...
![Album image #75 Album image #75](/albums/img/2/3/9/442239-10105-78-720.jpg)
We can fix that with a little filler.
![Album image #76 Album image #76](/albums/img/2/4/2/442242-10105-20-720.jpg)
I used card stock to make the small curved gussets at the bottom of the windscreen frame.
![Album image #77 Album image #77](/albums/img/2/4/3/442243-10105-93-720.jpg)
Camera pods added to the side of the intakes. The are clear plastic, and the bottom was painted black first.
![Album image #78 Album image #78](/albums/img/2/4/4/442244-10105-59-720.jpg)
Alclad grey primer goes on.
![Album image #79 Album image #79](/albums/img/2/4/5/442245-10105-84-720.jpg)
I think the wing seams will be a problem.
![Album image #80 Album image #80](/albums/img/2/4/6/442246-10105-21-720.jpg)
And finally some anti-flash white.
![Album image #81 Album image #81](/albums/img/2/4/7/442247-10105-24-720.jpg)
Yup, we have to fix those wing seams.
![Album image #82 Album image #82](/albums/img/2/4/8/442248-10105-37-720.jpg)
I used white putty to try and smooth these areas out.
![Album image #83 Album image #83](/albums/img/2/4/9/442249-10105-53-720.jpg)
Now I think I can live with it.
![Album image #84 Album image #84](/albums/img/2/5/0/442250-10105-10-720.jpg)
All that white...
![Album image #85 Album image #85](/albums/img/2/5/1/442251-10105-73-720.jpg)
But I think the wing seams are OK now.
![Album image #86 Album image #86](/albums/img/2/5/2/442252-10105-97-720.jpg)
A panel line wash with a very light grey helps to break up the monotone finish. A lot of re-scribing on the top of the wing near those seams!
![Album image #87 Album image #87](/albums/img/2/5/3/442253-10105-41-720.jpg)
More re-scribing on top of the fuselage spine behind the cockpits.
![Album image #88 Album image #88](/albums/img/2/5/4/442254-10105-25-720.jpg)
Starting the stickers. Exhaust area is several shades of Alclad,
![Album image #89 Album image #89](/albums/img/2/5/5/442255-10105-91-720.jpg)
The light blue walkway stripes broke into several sections when applying. What a pain to get them back together and lined up.
![Album image #90 Album image #90](/albums/img/8/1/1/442811-10105-62-720.jpg)
The old gal has her shoes on finally!
![Album image #91 Album image #91](/albums/img/8/0/5/442805-10105-10-720.jpg)
Adding some photoetch to the gear bays.
![Album image #92 Album image #92](/albums/img/8/0/8/442808-10105-32-720.jpg)
Main gear hydraulic lines are made from some very fiddly solder.
![Album image #93 Album image #93](/albums/img/8/0/6/442806-10105-53-720.jpg)
I'm starting to call her the "Bird of Prey." I think she was designed by Klingons.
![Album image #94 Album image #94](/albums/img/8/0/7/442807-10105-83-720.jpg)
Now I'm off to paint all the control surfaces!
![Album image #95 Album image #95](/albums/img/7/7/4/448774-10105-49-720.jpg)
Wing flaps are on.
![Album image #96 Album image #96](/albums/img/7/7/5/448775-10105-61-720.jpg)
As are the tailplanes/elevators. The tailplane flaps are posed slightly off of neutral.
![Album image #97 Album image #97](/albums/img/7/7/6/448776-10105-98-720.jpg)
More painting on the avionics bay. There are some photoetch pieces to add. Intake doors are posed open, as was the case on the ground.
![Album image #98 Album image #98](/albums/img/7/7/7/448777-10105-53-720.jpg)
Another view of the intake doors. CMK did a nice job casting these pieces.
![Album image #99 Album image #99](/albums/img/7/7/8/448778-10105-24-720.jpg)
CMK even provide the linkage from the airbrake actuator to the central drive system. Can you see it?
![Album image #100 Album image #100](/albums/img/7/7/9/448779-10105-10-720.jpg)
Not sure what I'm going to do with the bomb bay.
![Album image #101 Album image #101](/albums/img/7/8/0/448780-10105-29-720.jpg)
A lot of the nose gear bay details will disappear when the remaining gear doors go on. They were typically closed on the ground.
![Album image #102 Album image #102](/albums/img/3/4/3/450343-10105-72-720.jpg)
OK, I think she's finished!
![Album image #103 Album image #103](/albums/img/3/4/5/450345-10105-60-720.jpg)
I don't have any parts left over.
![Album image #104 Album image #104](/albums/img/3/4/6/450346-10105-82-720.jpg)
Resin fin with leading edge intake is from Odds & Ordnance.
![Album image #105 Album image #105](/albums/img/3/4/0/450340-10105-26-720.jpg)
Gold coating on canopy windows is a mix of Gunze Clear Yellow and Clear Orange.
![Album image #106 Album image #106](/albums/img/3/4/4/450344-10105-29-720.jpg)
Vent tubes under the exhaust area are just some bits of wire.
![Album image #107 Album image #107](/albums/img/3/4/1/450341-10105-58-720.jpg)
Yup, Klingons.
![Album image #108 Album image #108](/albums/img/3/4/2/450342-10105-32-720.jpg)
![Album image #109 Album image #109](/albums/img/3/5/2/450352-10105-56-720.jpg)
I hope I never have to scribe another panel line!
![Album image #110 Album image #110](/albums/img/3/4/7/450347-10105-90-720.jpg)
Devilishly difficult to get a good picture of an all-white model. Solution: no more overall white schemes!
![Album image #111 Album image #111](/albums/img/3/4/8/450348-10105-28-720.jpg)
Beautiful design, it's really too bad it never went into production.
![Album image #112 Album image #112](/albums/img/3/4/9/450349-10105-69-720.jpg)
I used Floquil Flat finish to give it an eggshell sheen.
![Album image #113 Album image #113](/albums/img/3/5/0/450350-10105-97-720.jpg)
![Album image #114 Album image #114](/albums/img/3/5/1/450351-10105-61-720.jpg)
Photoetch resraints add a nice touch to the avionics bay.
![Album image #115 Album image #115](/albums/img/3/5/3/450353-10105-56-720.jpg)
Коментари
35 8 January 2018, 14:52
![](/profiles/img/10105-s.jpg)
Hi mates, it's time to start another project. The British Aircraft Corporation (BAC - a Government desired merger of English Electric, Vickers, Bristol Aeroplane, and Hunting) TSR.2 has always fascinated me, and I started collecting the aftermarket parts before I even had the kit. I opted for the later Stratos 4 version of the kit since it was more readily available and it has a much better decal sheet. And all the parts are there to build the original TSR.2, and I can save the lady jockeys for some future project.
Technically, the TSR.2 was the Supermarine Type 571 (Vickers having absorbed Supermarine a few years earlier) but in reality it mostly resembled the English Electric P.17 design. As it turned out, this marvelous aircraft only made a handful of test flight before the project was cancelled. Mythology aside, the project was terminated because of cost and the change in defence policy when the UK removed the "East of Suez" requirements. I hope I can due justice to Britain's lost bomber (or Britain's lost Cold War strike aircraft depending on which book you read).
The Airfix kit is not bad at all, but could use some extra details here and there. I've started fitting the internal resin pieces and will be moving on to detailing the cockpit next. Welcome aboard to those who like big white pointy things!
8 January 2018, 15:30
![](/profiles/img/13151-832-s.jpg)
Whenever I get to visit Duxford or Cosford, I just want to go up to the last airframes and give them a big hug! 🙂 The best of British that never was! Do it proud Bill!
9 January 2018, 00:15
![](/profiles/img/11091-s.jpg)
Glad to see you started this, mine is on hold, good luck, but you never needed that
9 January 2018, 04:04
![](/profiles/img/10105-s.jpg)
Some work done on the cockpit. I used an alloy finish on the ejection seat structure (Alclad Dull Aluminum), with black cushions and a dark grey headrest. Harnesses are from the Eduard set, as those in the CMK set are the wrong colour (tan), and look suspiciously like WWII surplus.
The instrument panels were fun. I used the CMK resin, but remember that the CMK photoetch (made by Eduard) was pre-painted in the wrong colour. The Airfix decals, however, are in the right colour. So I added the photoetch to the resin and then applied the Airfix decals over the top, with a lot of solvent to make them snuggle down over the etch. Here's the deal, though - I had to cut the Airfix decals into individual sections and add them one at a time, matching instruments up the best I could. The pilot's panel has eight separate decals, whilst I lost count on the navigator's.
The cockpit tub, seats, and instrument panels all had a wash applied made from Tamiya dark grey, Future, water, and a drop of some magic ingredient that escapes me presently. I like this wash, you can use it over matt paint and you don't have to wipe off any residue after it's dry. All the paint molecules seem to line up along the edges, and the clear Future gives a nice gloss layer over everything else - ready for any decals you want to apply. For instance, the decals for the side consoles (also several individual pieces each). Whoever thought this up was brilliant - oh yeah, that Barracuda guy. Nice man. A flat varnish was applied when I got tired of working on it.
Next I need to look at the destructions to make sure I don't do something out of sequence that I'll regret later on. Some new pictures have been posted. Cheers for now, Bill
10 January 2018, 23:42
![](/profiles/img/21096-573-s.jpg)
Cockpit will be awesome. tons of work with all the resin, but it will be a very nice model at the end.
10 January 2018, 23:47
![](/profiles/img/10105-s.jpg)
Well, the CMK intakes will need a bit of work to properly conform to the fuselage. Ah, the joys of resin!
11 January 2018, 16:14
![](/profiles/img/27826-126-s.jpg)
These air intakes have to look well once fit, like the rest of resins. Good job, Bill.
11 January 2018, 18:11
![](/profiles/img/10105-s.jpg)
Thanks everyone. I've done a small amount of additional work on the BWPT (Big White Pointy Thing). I had to modify the intake cones so they would contact the fuselage side, and this was easily done with some sheet styrene. The intakes were puttied and blended into the fuselage, but there will be some more work to be done here once the top fuselage section is added. Some very strange engineering by Airfix in this area, which is compounded by the resin intakes being very slightly undersized (shrinkage?) but it will all work out OK.
I also spent some time getting the airbrake wells added to the top rear fuselage section - the resin parts from CMK are much nicer than what comes in the kit. The TSR.2 had an unusual system for deploying the four airbrakes where all were connected to a single central screwjack. CMK provide not only the hydraulic actuator that opens/closes the petal, but also the shaft that connects the actuator to the central drive. Nice work!
I removed all of the exhaust pieces from the pour blocks, and I will use these along with photoetch flame holders from the Eduard set. Eduard also have this roll-up photoetch afterburner nozzle, but it would be almost completely hidden inside the exhaust shroud, so why bother? I'll just use the resin.
I started painting the wheel wells, since it will be much easier to do this now before the fuselage is closed up. Photos show that XR220 had light grey wheel wells, so I used Gunze H332 Light Aircraft Grey. Equipment used on the aircraft solely for flight test purposes (sensors/recorders, etc.) were painted orange, and some components in the main gear bay got this treatment using Gunze H14 Orange.
The wells for the lower airbrakes require more significant modification to the lower fuselage, so I'm avoiding that at present! Enjoy the few new photos that I posted. Cheers, Bill
15 January 2018, 14:39
![](/profiles/img/10105-s.jpg)
A little more progress - at least the fuselage is closed up now. Airfix moulded the vents above the intakes but they needed to be drilled out. The nose gear bay was added along with the cockpit. Test fitting the navigator's instrument panel showed that it protruded too much into the cockpit, so I fixed that. Now it looks much better.
After gluing the fuselage halves together, I reinforced the top seam underneath with pieces of sheet styrene. For some reason, I just didn't trust that seam by itself! The rear fuselage will need some spreaders, too, to set the sides at the correct width. The main landing gear wells (that big hunk of resin) slip into the closed fuselage easily, but final positioning and gluing will probably wait until the bottom section is added. It looks like it might be tricky.
Before the wings go on, I have to cut out the flaps which is next on the agenda. Cheers, Bill
18 January 2018, 18:27
![](/profiles/img/10105-s.jpg)
I just finished up some wing surgery to make way for the new resin flaps. I've documented the necessary cuts with some more photos. I'll say one thing - this kit had a lot of negative comments concerning fit, etc. when it first came out. But I've found the only real modifications or fixes that I've had to do (so far) have been to accommodate the CMK resin parts. The kit itself, although it has some odd engineering, has been OK.
@playtime 222 - The red filler is an automotive glazing putty called NitroStan made by Standard Coatings Company. It's been around forever. I found it way back in the 60s when I worked part time in an auto body repair shop. A one kilogram tube costs about $20 here in the USA, and will literally last a lifetime of making models (unless they're really bad kits!). I like it because it dries fast, sands easy, and feathers to a beautiful edge. I've never had any kind of paint affect it in any way. Only downside is that it can shrink a bit, so two applications are sometimes necessary.
19 January 2018, 03:00
![](/profiles/img/17635-610-s.jpg)
Hey Bill, Was thinking of getting the CMR intakes and tail pipe. Do you think they are worth it? Provide much of a lift over the kit parts? I have the other CMR kits (and pavla cockpit)?
20 January 2018, 04:11
![](/profiles/img/14213-529-s.jpg)
Very interesting project Bill. A month or 2 ago I visited the RAF museum at Cosford UK and looked at this aircraft closely. Amazing aircraft indeed!
20 January 2018, 10:27
![](/profiles/img/10105-s.jpg)
Thanks, mates! I took the three pieces for the top of the fuselage (the wing, top of the intakes, and top of the rear fuselage) and joined them together. Airfix have you do this by putting each piece onto the main fuselage individually, but I wanted to make sure that the seams between these three pieces were carefully aligned, and wouldn't leave any steps as has been reported elsewhere. After all, any bad seams here are going to be very visible on the model. By doing it this way, the seams look great, and shouldn't need any filler. The seams are on natural panel lines. Once I did this, I was a bit worried that it might give me trouble attaching it to the fuselage, but it fits great! This is definitely the way to build this part of the model, don't pay any attention to the instructions! 🙂
You can see in the new photos how the resin pieces on the bottom of the wing make a nice pocket for the resin flaps to fit into.
@Mark Medwell - the tail pipes are quite nice, and fit well. Definite improvement over the kit parts. The intakes, at least my samples, were slightly undersize, so there is a bit of fettling with filler required. However, if you want the auxiliary doors open on the side of the intakes, which is the way the aircraft almost always was on the ground, then I would get them. The small auxiliary doors that are part of the CMK set are very detailed - you can see the ribs inside at the edges.
@Erik Leijdens - You lucky guy! I envy you. I'm coming over to the UK in April, but I don't know if I'll have a chance to see either one of the TSR2 aircraft. Maybe!
20 January 2018, 13:21
![](/profiles/img/10105-s.jpg)
I added a few new photos - I've added the resin parts for the lower airbrakes, and I started taking a look at the main landing gear splay angle. When these kits were first released, the angle that the main gear legs "splayed" out was a big topic of discussion. It looks like I can get close to the correct angle with careful gluing - probably good enough for me. Despite all of my builds, I'm not really a rivet counter. No, really, I'm not. 🙂
21 January 2018, 21:13
![](/profiles/img/10105-s.jpg)
I took a week off and went to Florida, but now I'm back. I've done some more work on the TSR.2 and posted some new pictures. Finally the fuselage is closed, and we move towards painting. Closing up the fuselage was much easier than expected thanks to the spreaders and shims that I added. Without those I think it would have been quite difficult to get everything aligned and not have any seams pop open.
4 February 2018, 18:52
![](/profiles/img/10105-s.jpg)
Lots of work recently. Finally the TSR.2 "Bird of Prey" is painted and the stickers are being applied. I spent quite a bit of time fixing and smoothing the wing seams, and then re-scribing that entire area. This is one part of this kit that everyone seems to have difficulties with. I guess I'm happy with where it is now, but there is still a lot of work to do before this project is finished. I've posted many new photos to show the progress. Cheers, Bill
21 February 2018, 14:58
![](/profiles/img/32434-521-s.jpg)
Excellent job Bill, this is definitely one of the best 1:72 representations I have seen for this A/C. Certainly are doing it justice!!! Looking forward to seeing it cross the finish line! Cheers!
21 February 2018, 16:27
![](/profiles/img/13641-502-s.jpg)
Grand job Bill, I admire your patience to fight the seams and those decal lines 👍
21 February 2018, 20:43
![](/profiles/img/13151-832-s.jpg)
The thought of finishing all that white scares the bejeezus out of me!. The very light grey shading/panel line works makes it look terrific though, and the anti-flash markings look spot on! This is turning out to be another real beauty Bill! 👍
22 February 2018, 07:45
![](/profiles/img/10105-s.jpg)
Thanks mates. The old gal has her shoes now, please have a look at the new photos. The landing gear was a bit of a challenge to get everything straight, and have all the flat spots on the tyres contact the ground evenly. Very strange design. The TSR.2 had a very obvious group of hydraulic lines that ran down each main gear strut, around the torque links and into the brakes. I tried to replicate this with the smallest solder I had and although it's not perfect, it ain't too bad. I started painting the details in the avionics bay (lots of switches!) and next I'll move on to the control surfaces (vertical fin, tailplanes, flaps, elevators, etc.) These have all been primed and are waiting for their coat of white. Cheers, Bill
23 February 2018, 02:13
![](/profiles/img/32952-618-s.jpg)
Looking great. I wish you could still get your hands on this kit. Time for a re-release Airfix?
23 February 2018, 09:52
![](/profiles/img/10105-s.jpg)
Hi mates, it's time for an update. Most of the gear doors are on, and I've added the extra linkage (known as the Aylesbury Tie) to the main landing gear. This was added during the flight test programme to reduce the lateral oscillations in the main gear when landing. The lower airbrakes and their actuators have been added, along with the wing flaps and the horizontal tailplanes/elevators. I also attached the small auxiliary intake doors (two per side). Some additional detail painting was done on the avionics bay. Things are looking pretty good! I need to do an overall varnish, preferably semi-gloss, add the canopies (which are ready to go) and the upper airbrakes and vertical fin. Oh, yeah, I've got the Master pitot tube. And a few antennae and other sensors and she'll be ready to go! Enjoy the new pictures. Cheers, Bill
1 March 2018, 15:54
![](/profiles/img/13151-832-s.jpg)
Becoming more fantastic with each update - blinkin' brilliant Bill! 👍 (Photo 97 - I think there might be a popped circuit breaker in the avionics bay? - Joke, honest! 🙂 )
2 March 2018, 15:47
![](/profiles/img/15122-902-s.jpg)
Very nice Bill, I like those low vis schemes of the Royal Air Force!
2 March 2018, 15:49
![](/profiles/img/10105-s.jpg)
Hi mates - the TSR.2 is finished. I'm not real happy with the photos, but I never said I was a photographer! I hope you like them. Cheers, Bill
5 March 2018, 20:33
![](/profiles/img/16661-726-s.jpg)
What a beautiful bird that was ! You've really done it more than justice Bill, Simply excellent modelmaking 👍 👍
5 March 2018, 22:22
![](/profiles/img/11761-776-s.jpg)
Bill, Just fantastic! Utterly beautiful! Truly sad that, along with the AVRO Canada CF-105 Arrow, it was cancelled. You have done a remarkable job, and in such a short time. You have my respect, sir! R/ Dutch
5 March 2018, 23:15
![](/profiles/img/user-s.jpg)
Very nice work, and idd, white models are difficult to photograph... let alone make them lively and interesting, but you've succeeded... very nice model, and a real pleasure to follow
6 March 2018, 07:42
![](/profiles/img/13641-502-s.jpg)
You might not be a photographer, but a Modeller (capital M intentional) for sure. It looks awesome on the pic 107 👍
6 March 2018, 08:53
![](/profiles/img/27612-321-s.jpg)
Pretty well along on this kit myself Bill. Used the same CMK sets as you. Cockpit and equipment bay are done and especially nice. Wheel wells & bomb bay are next. Too bad CMK didn't do a bomb pay package to stick in there as it looks at Cosford. Would seem to be easy. Thanks for this great build. It has been my guide so far through the project
3 May 2023, 15:57
![](/profiles/img/10105-s.jpg)
Thanks Mike. I'm glad that my build has been of some help to you. It wasn't the easiest kit to build but I like how she came out. I'm doing another white bomber now - the Airfix kit of the Handley Page Victor. One of my favourite aircraft. Cheers, Bill
3 May 2023, 16:36
![](/profiles/img/27612-321-s.jpg)
Well, after a long haul my TSR is finally finished. Very pleased with the result. I just wish it was easier to handle. It seems everywhere you try to grab it there's something delicate sticking out!
See a photo at this link: [img1]?dl=0&rlkey=14rjyyxybxw3r4zrzubsa6qv7
29 June 2023, 16:09
Album info
With a little help from a pile of resin...