H.S. Buccaneer S2B (Airfix 1:48)

1
March 29, 2020
2
March 29, 2020
3
March 29, 2020
4
March 29, 2020
5
March 29, 2020
6
March 29, 2020
7
March 29, 2020
8
March 29, 2020
9
March 29, 2020
10
April 5, 2020
11
March 29, 2020
12
March 29, 2020
13
March 29, 2020
14
March 29, 2020
15
April 8, 2020
Ejection seats done
16
March 29, 2020
17
April 15, 2020
Cutting out the wheel wells caused the bottom half of the fuselage to warp, to get the bomb bay in place without gaps had to clamp the whole fuselage in place to remove the warping in the bottom half
18
April 15, 2020
Forgot to install these two ecjection seat rails
19
April 15, 2020
20
April 15, 2020
Cockpit ready for final assembly
21
April 15, 2020
Dry fitting the cockpit, the front starboard wall will need some trimming
22
April 15, 2020
Port wall had some minor gaps to fill
23
April 15, 2020
Starboard walls fit aren't the best...rather biggish gaps
24
April 15, 2020
25
April 15, 2020
26
April 15, 2020
27
April 15, 2020
Test fitting the completed cockpit, which actually sits really nice in place
28
April 15, 2020
29
April 15, 2020
Cut out too much of the original glareshield to fit the resin shield, otherwise the shield will sit too much forward
30
April 15, 2020
Gaps filled in
31
April 15, 2020
32
April 20, 2020
Navigator blast shield installed
33
April 20, 2020
34
April 20, 2020
35
April 22, 2020
36
April 20, 2020
The jet pipe needs some clean up
37
April 20, 2020
38
April 20, 2020
The jet pipes need shortening due to the resin wheel wells taking more space than the originals
39
April 20, 2020
40
April 20, 2020
41
April 20, 2020
42
April 20, 2020
43
April 20, 2020
44
April 20, 2020
45
April 20, 2020
46
April 20, 2020
Everything is sanded as the plastic is really rough
47
May 10, 2020
Scribing some panel lines
48
May 10, 2020
49
May 10, 2020
50
May 10, 2020
51
May 10, 2020
Fitting issues...can't press the top part in to align with the bottom half as the epoxy used to attach the resin cockpit makes it impossible...
52
May 10, 2020
...so therefore forced the bottom half outwards to align with the top part.
53
May 10, 2020
More alignment issues
54
May 10, 2020
The nose sections forced into position, glued and lots of tape to hold it in place. Let it sit for a day to set. The fuselage is glued in sections otherwise you can't get everything to align.
55
May 10, 2020
Next the tail section is glued.
56
May 10, 2020
The air intakes didn't align with the fuselage so some pieces of styrene had to be inserted here.
57
May 10, 2020
58
May 10, 2020
The whole fuselage eventually glued in place.
59
May 10, 2020
60
May 10, 2020
61
May 10, 2020
62
May 10, 2020
PE parts from Airwaves added to the air brakes
63
May 10, 2020
64
May 10, 2020
65
August 11, 2020
66
August 11, 2020
67
August 11, 2020
68
August 11, 2020
69
August 11, 2020
70
August 13, 2020
71
August 13, 2020
72
August 13, 2020
Assembling the slipper tanks.
73
August 13, 2020
74
August 17, 2020
Lots of filler...
75
August 17, 2020
76
August 17, 2020
Primer on
77
August 17, 2020
78
August 17, 2020
Slipper tanks done
79
August 13, 2020
Wheels need to be masked
80
August 13, 2020
81
August 14, 2020
82
August 17, 2020
Made a mistake here...those silver parts should be same color as the rest of the gear.
83
August 17, 2020
Lading gears fixed and some wiring added.
84
August 19, 2020
Completed landing gear.
85
August 19, 2020
This doesn't look right...
86
August 23, 2020
Should look like this.
87
August 23, 2020
Used the Eduard PE instead of the Airwaves one for the bottom, now looks more like the real thing.
88
August 19, 2020
Tail section installed.
89
August 19, 2020
90
August 23, 2020
91
August 23, 2020
92
August 23, 2020
Careful drilling...
93
August 23, 2020
Just a dry fitting, the pitot tube will be assembled last as it's a prime candidate to be broken off or be bend.
94
August 23, 2020
95
August 23, 2020
96
August 25, 2020
Used a spare HUD I found in a box as the kit's HUD is rubbish
97
August 25, 2020
98
August 25, 2020
99
August 25, 2020
100
August 25, 2020
101
August 27, 2020
102
August 27, 2020
Primer on.
103
August 28, 2020
Some more sanding needed...
104
August 28, 2020
These gaps looks a bit big
105
August 28, 2020
106
August 28, 2020
That looks better
107
August 28, 2020
108
August 31, 2020
109
August 31, 2020
110
August 31, 2020
111
August 31, 2020
112
September 3, 2020
The angle of the refuelling probe was too much, it should be about 10°.
113
September 3, 2020
Refuelling probe fixed.
114
September 6, 2020
115
September 6, 2020
116
September 6, 2020
117
September 14, 2020
118
September 14, 2020
The Kits-World decals are excellent
119
September 18, 2020
The yellow stripe should be higher up on the fuselage
120
September 18, 2020
Carefully loosening the decal
121
September 18, 2020
Yellow stripe in correct position now.
122
September 18, 2020
Then this happened...somehow the stripe lengths are different, didn't spot it when applying them.
123
September 18, 2020
Loosening the decal again...
124
September 18, 2020
Stripe fixed.
125
September 18, 2020
All decals applied.
126
November 30, 2020
First time I'm using an oil wash.
127
November 30, 2020
128
November 30, 2020
129
November 30, 2020
Wash applied.
130
November 30, 2020
131
November 30, 2020
Tanks and missiles attached.
132
November 30, 2020
The slipper tanks sit too far outward on the wings if using the guide pins, it should not go over the wing hinges. **Correction - these are actually the correct positions, fixed later on.
133
November 30, 2020
Another view of the slipper tank sitting too much outwards on the wing.
134
November 30, 2020
Slipper tank in the correct position - actually not. Fixed later on.
135
November 30, 2020
The position of the fuel tanks were actually correct on closer inspection...they do go slightly over the wing hinges.
136
November 30, 2020
Fuel tanks reattached in the correct positions now.
137
December 9, 2020
The canopy was sanded as it had some scratches and wasn’t clear.
138
December 9, 2020
Time to try my new rotary tool to polish the canopy.
139
December 9, 2020
140
December 9, 2020
141
December 9, 2020
142
December 9, 2020
Undercarriage in place.
143
December 9, 2020
144
December 9, 2020
I lost the clear part for the navigation light on top of the fuselage so made a new one with Glue ‘n’ Glaze.
145
December 9, 2020
146
December 10, 2020
Ejection seats installed.
147
December 10, 2020
Just a test fit...the pitot tube will be installed and painted last to avoid knocking or bending it.
148
December 10, 2020
Awaiting a final semi gloss coat.
149
December 10, 2020
Building the ladders and FOD guards.
150
December 10, 2020
151
December 10, 2020
152
December 10, 2020
153
December 10, 2020
154
December 14, 2020
With closed canopy and before adding the ladders and FOD guards to the engine intakes.
155
December 14, 2020
156
December 14, 2020
157
December 14, 2020
158
December 14, 2020
159
December 14, 2020
160
December 14, 2020
161
December 14, 2020
162
December 14, 2020
163
December 14, 2020
164
December 14, 2020
165
December 14, 2020
166
December 14, 2020
167
December 14, 2020
168
December 14, 2020
169
December 14, 2020
170
December 14, 2020
171
December 14, 2020
172
December 14, 2020
173
December 14, 2020
174
December 14, 2020
175
December 14, 2020
176
December 14, 2020
177
December 14, 2020
178
December 14, 2020
179
December 14, 2020
180
December 14, 2020
181
December 14, 2020
182
December 14, 2020
183
December 14, 2020
184
December 14, 2020
185
December 14, 2020
186
December 14, 2020
187
December 14, 2020
188
December 14, 2020
189
December 14, 2020
190
December 14, 2020
191
December 14, 2020
192
December 14, 2020
193
December 14, 2020
194
December 14, 2020
195
December 14, 2020
196
December 14, 2020
197
December 14, 2020
198
December 14, 2020
199
December 14, 2020

Коментари

28 29 March 2020, 00:26

Megan Harris
That cockpit detail is absolutely insane! How do you do it?

22 April 2020, 21:49

Celliers
Hi Megan. I used a resin cockpit set from Neomega as the Airfix one had basically no detail on it and I'm planning to have an open cockpit. Just had to take my time carefully painting the panels and dials. Had some fitment issues with some of the side walls but once inside the fuselage it won't be noticeable 🙂

9 May 2020, 22:21

Nathan Dempsey
Nice work so far & good notes on the construction too.

11 August 2020, 16:28

Michael Phillips
Umm, wow. That is some incredible work there. I have always wanted to do a Bucc, but had been waiting on Tanmodel to release one, which may never happen as it seems. But you are knocking this one out of the park!

11 August 2020, 16:47

Daniel
this looks like a lot of work - but will be a rewarding outcome for sure, taking a seat 👍

11 August 2020, 19:01

Celliers
Thanks Nathan, Michael.
@Daniel, this kit has a lot of work, nothing fits properly so you have to love filling and sanding. And then I somehow got into riveting the whole thing which added so much more work...I hope to have everything assembled in the next week ready for painting.

17 August 2020, 19:30

David Taylor
Hi Celliers got 2c/d in the stash.Watching to see how this one goes.

21 August 2020, 16:56

Jos Jansen
Missed this one...following!

21 August 2020, 17:42

Alexander
Looks like a massive amount of work, but it surely paid out so far - great detailwork in the cockpit and wheel wells! 👍

21 August 2020, 20:35

Gerald
👍

23 August 2020, 06:32

Ata Turgay
I love landing gears. Great work.

23 August 2020, 19:27

Slavo Hazucha
Great plane & nice work on all the details, joining mid-season to see the further stages! 👍

24 August 2020, 09:16

Celliers
Thanks David, Jos, Alexander, Gerald, Ata & Slavo.

25 August 2020, 19:01

David Taylor
What load out are you doing Celliers,anti ship or mud moving.

26 August 2020, 08:32

Celliers
@David, I'm doing the anti ship load.

27 August 2020, 13:46

Nathan Dempsey
I've got to get that refueling probe/pitot set. It looks much nicer than the kit part!

27 August 2020, 14:21

Danumurthi Mahendra
enjoying the journey, as well as the destination. great in-progress photos!

27 August 2020, 15:12

Jos Jansen
Great iconic jetplane...you are making a stunner!

28 August 2020, 13:02

playtime 222
Drool!

31 August 2020, 21:15

David Taylor
Hi Celliers,if you have either Kinetic harriers they have a super set of Sea Eagles

7 September 2020, 19:31

Slavo Hazucha
great progress & a lovely clean job on the camo & nozzles 👍

7 September 2020, 19:38

playtime 222
Grumble... Mutter.... Martels... 😄

8 September 2020, 00:42

Clifford Keesler
Very nice. Too bad those are so hard to find now.

8 September 2020, 01:14

Guillaume Blanchet
Very impressive !!

8 September 2020, 02:00

David Taylor
sorry playtime later Buccs had eagles.

8 September 2020, 18:10

Celliers
Thanks all for the comments. Just started with the decals, decided to get the Kits-World decals sets as the kit's decals has seen better days being over 25 years old...

14 September 2020, 20:23

Celliers
Time to finish this baby, she's been sitting on the half build shelf long enough...

30 November 2020, 19:08

Nathan Dempsey
Nice to see this one going again. Looks like you're nearly there.

30 November 2020, 19:17

Jos Jansen
Great Celiers...still watching and you can see the finish line!

30 November 2020, 19:29

Gary Victory
Fanstic build. A real labour of love. Looking forward to the final reveal.

1 December 2020, 07:50

Maxim Malparte
Looks delicious! Can't wait to see it finished.

1 December 2020, 08:02

Clifford Keesler
Agree, can't wait to see it done.

2 December 2020, 00:15

Francky
I have this kit is my stash as well. I see you used a few aftermarket sets from Eduard and others. Which of these do you find the most useful, now that it is done?

Your model is very well done, it motivates me to start on mine 🙂

10 December 2020, 10:21

Augie
Just lovely.. so nice to see one of these coming out

14 December 2020, 13:33

Celliers
She's finally finished 🙂
Thanks @Augie.
@Francky, I would definitely get the Neomega cockpit and wheel well resin set as the kit's are very basic, the Airwaves speed brakes PE set as well as the Master pitot tube and refueling probe. I only used a few parts of the Eduard PE sets.

14 December 2020, 13:41

Nathan Dempsey
That's a build to be proud of Celliers. Well done.

14 December 2020, 15:27

David Taylor
Brill build.

14 December 2020, 16:04

Clifford Keesler
I agree with everyone just a beautiful build.

15 December 2020, 02:24

Francky
@Celliers: and my wishlist just got a bit longer 🙂 Thanks for the info.

15 December 2020, 10:09

gorby
Fantastic job! Well done for wrestling this kit into shape.

15 December 2020, 15:31

playtime 222
Great job - Notes taken. I have 2 of these cos I was lucky enough to get the accidental double boxing.

15 December 2020, 15:54

Celliers
Thanks @Nathan, @David, @Clifford, @gorbygould.
@playtime 222 - lucky you getting 2 kits. I have another one that I'm going to build in SAAF colours, but not anytime soon. The next project better be easier than this one.

15 December 2020, 19:20

Project info

H.S. Buccaneer S2B (Airfix)

199 слике

1:48

Завршено

1:48 H.S. Buccaneer Exterior (Eduard 48130)

1:48 H.S. Buccaneer S2B - Interior (Eduard 48132)

1:48 Buccaneer - Pitot Tube and Refuelling Probe (Master AM-48-100)

Blackburn Buccaneer S Mk.2b

Royal Air Force (1918-now)
No. 12 Sqn. XW530
1988 Cold War - Lossiemouth, Scotland
BS381C:641 BS381C:638

Сви албуми

Прикажи све албуме »