Зид
Wall
![](/profiles/img/136622-960-s.jpg)
додао је нови фотоалбум.
All comments (5) » 21 16 March, 08:07
![](/profiles/img/136622-960-s.jpg)
Thank you, Robert! Apart from the floats and the small fiddly windows, it went together quite well.
17 March, 12:18
March 16, 2024
![](/profiles/img/136622-960-s.jpg)
додао је нови фотоалбум.
10 слике
Danish Spitfire XI![View album, image #9 View album, image #9](/albums/img/3/9/8/1660398-136622-35-720.jpg)
1:72
For those following; sorry, I don‘t work very fast :) Anyway, all major components assembled, and filler + sanding where...
Пројекат: RDanAF Supermarine Spitfire PR Mk. XI
All comments (21) » 15 15 January, 16:19
![](/profiles/img/13136-468-s.jpg)
Nice looking cockpit! I built the Mk.X boxing and wondered the same thing about the floor/bulkhead fit… I probably have some spare Stoppel decals if you need a '1'.
16 March, 11:12
March 10, 2024
![](/profiles/img/136622-960-s.jpg)
Would anybody happen to have any photos of the interior of a Swedish Air Force („Flygvapnet“) Boeing-Vertol Hkp 4? Specifically as used by the air force, not the navy version….
10 March, 10:15
![](/profiles/img/136622-960-s.jpg)
је власник овог предмета
![1:72 CH-46 Sea Knight - wheels w/ weighted tyres (Armory AR AW72364) AR AW72364](/products/img/2/3/7/1438237-53752-55-t180.jpg)
CH-46 Sea Knight - wheels w/ weighted tyres
Armory 1:72AR AW72364
![UA UA](/s/images/flags7/32/UA.png)
10 March, 10:10
January 27, 2024
![](/profiles/img/136622-960-s.jpg)
је власник овог предмета
![1:72 Canopy Mask: Spitfire PR.Mk.XI - KP Kits - (Peewit M72300) M72300](/products/img/4/6/6/1414466-33840-47-t180.jpg)
Canopy Mask: Spitfire PR.Mk.XI - KP Kits -
Peewit 1:72
M72300 27 January, 12:59
January 26, 2024
January 25, 2024
![](/profiles/img/136622-960-s.jpg)
је власник овог предмета
25 January, 22:29
![](/profiles/img/136622-960-s.jpg)
I've always wanted this since I took up modeling again a couple, but until a couple of days ago it effectively wasn't available anywhere in Europe. Managed to get one from Super Hobby in Poland, they were sold out a couple of days later. Looks a bit daunting in places, particularly the engine which seems to consist of an inordinate amount of parts. I can't see any differences between this kit and the original Kitty Hawk offering; the decals are the same, for example.
25 January, 22:33
January 21, 2024
![](/profiles/img/136622-960-s.jpg)
Nice, good-value-for-money re-issue of the ICM kit, with the following minor issues:
1) The rudder control horns are positioned too high up on the rudder, they need to be located one rudder rib distance further down
2) Decals for HB-UBC are provided in the kit, this has a tail wheel (not in the kit) and not a tail skid.
3) The rudder control cables connect to a sliding bracket (not in the kit) extending out of the fuselage, and do not come out of the fuselage.
4) Flying wires are thicker than the control surface cables, not the same thickness as suggested in the instructions.
5) The L-shaped part on the fuselage lower surface is an idler lever for the aileron controls, but the rest of that arrangement is missing.
On a positive note, the blind flying hood is also included in the kit (not used on the two civil aircraft for which decals are provided), as is an upper rear fuselage part without the anti-spin strakes, enabling an (earlier) DH.82 to be built as well, and not only a DH.82A.
Looking forward to getting started with it!
21 January, 10:52
![](/profiles/img/136622-960-s.jpg)
I have bought this for my Revell re-pop of the 1/32 ICM Tiger Moth. It‘s very nice, but I do notice the following issues:
1) The lap belts are attached to the lower-most fuselage longerons, not halfway up the fuselage.
2) There are three throttle levers, but only two are shown in the instructions. The third one could be used as a mixture lever, but then only in the rear cockpit.
3) The harness locking pins and spring clips are too large and unrealistically two-dimensioal. Moreover, they are attached by strings to the shoulder belts, not the lap belts.
4) The shoulder belts are not directly attached to the panel behind the seats, but to a steel wire running in the indentation in each panel.
5) The upper edge of the required cut-out in each instrument panel for the compass should be curved, not straight.
It would be worthwhile checking some of the many walkarounds in the Internet, before using this set
21 January, 10:37
January 13, 2024
January 12, 2024
![](/profiles/img/136622-960-s.jpg)
added a new article to његов personal gallery:
7 12 January, 05:19
![](/profiles/img/10148-258-s.jpg)
Wonderful and inspiring model, great outcome- and I really like your article!
12 January, 06:15
![](/profiles/img/136622-960-s.jpg)
Many thanks, Roland. Very flattering, as I have been enjoying and admiring your models and building style on Modellversium for many, many years!
Grüße aus München
Kenneth
12 January, 06:59
January 11, 2024
January 7, 2024
![](/profiles/img/136622-960-s.jpg)
је власник овог предмета
![1:72 Supermarine Spitfire PR Mk.XI (Kovozávody Prostějov KPM0293) KPM0293](/products/img/7/6/7/1445767-12741-71-t180.jpg)
Supermarine Spitfire PR Mk.XI "International"
Kovozávody Prostějov (KP) 1:72
KPM0293 (72293) 2022 Нови декали/налепнице 7 January, 15:24
January 2, 2024
December 28, 2023
December 27, 2023
December 25, 2023
December 24, 2023
wnolder.php?lang=sr
2023-12-24 15:33:15
2023-12-24 15:24:51
136622
/ajax/wnolder.php?lang=sr&sd=2023-12-24 15:33:15&md=2023-12-24 15:24:51&filter=&w=136622
todo