Nyhetsflöde

Derek Buckmaster
Excellent detailing with the PE! Looking very nice, can't wait for un-masking!

Villiers de Vos
Interesting subject. Nice work on the interior.

Nicolas
Oh, a kit from my favorite area of interest. I'm in. Great start with the instrument panel.

Michael Kohl
Like the plane and the livery you are going for.
My two cents on one or two aspects: I found the brass undercarrige and the cockpit section you listed as aftermarket pretty useless. The undercarriage doesn´t solve the problem to ease the alignment of the landing gear and the cockpit section doesn´t provide any better detail than the kit parts. I set both aside and rescribed the soft outlines of the cockpit doors. Pouring transparent resin into the cabin windows gave a nice flush appearance. You may consider that.
Good luck with your build. I will follow with keen interest.

Stephan Fässler
Thanks Michael and Nicolas. As my second kit to build, I thought I spice it up a bit with some aftermarket stuff, indeed, the new cabin with the new windows gave me some head scratching as to how install it, then figured it eventually out. My alignment looks a bit messy and I hope u can make it look aligned with putty etc… so far my opinion as an inexperienced builder is that you could safely leave it stock, as is….
I did not come yet to the brass parts and hope it will be better with these parts. Let's see 🙂

Thomas Kolb
I am happy to take a seat! I personally find red liveries extremely difficult to pull off, so I am watching with great interest!

Łukasz Gliński
Following this challenge.
The Aerocraft cockpit will require a lot of sanding, but the original windshield is definitely too narrow - been there, done that 🙂

Zbynek Honzik
Taking a seat. And fingers crossed that the strength and motivation will last until successful completion!

Guy Rump
Looking good, following. 👍

J35J
Great work so far! Looking forward to see the final result.

Stephan Fässler
Calling it complete for now.
Overall I enjoyed this kit, tricky to paint the red stripes and the nose was not properly done.
As a beginner I probably would not recommend the cockpit mod unless you have the proper tools, which I was missing sometimes 🙂
This was brush painted and spray can paint from revell I purchased with the kit to get started, meanwhile upgraded my collection with Mr Hobby and MRP. Revell is just awful for airbrush and mediocre for brush painting, but then again, I am no expert.
Unfortunately the „twotter" has some slight tilt, one of many mistakes happened during the build, but I'm happy I did not have to bin the whole thing 🙂
Cheers and onwards to the next one. You may deboard now…

TH SCALE MODELS (Thomas Haberl)
That is art! I have to take a first row seat here and see the progress. Very impressive 👍

Spanjaard
certainly not going to miss thus master class

Dave Flitton
Wow, watching!!

Skyhiker
Right on!

Greg Baker
Oh, sign me up. I'd watch F_IV do the laundry.

Robert Podkoński
I will follow this talent show with pleasure.

gorby
Lovely work.

Michael Kohl
Surely another build that will leave me speechless and striving to come closer to this level.

William Adair
Omg thanks everyone. You guys are the best! I'm interested to see how this one comes out. I'll add more progress soon. 🤞

Ludvík Kružík
I like old planes from the early days of aviation. Your scrathbuild is fantastic. I admire how you can render all the little details in this scale. I wish you continued success in building this model and look forward to the sequel.

Bruce Huxtable
Your talents are beyond my comprehension.... Totally amazing scratch building 🙂 This little gem is already gorgeous🙂

Shar Dipree
Great work so far! 👍👍👍👍

bughunter
Another great little bird in that microscopic scale 👍

William Adair
Added a new pic. Starting on the cockpit details 👌

Bruce Huxtable
More micro-perfection. Astonishing 🙂

Michael Kohl
By the way: will your book be available in Telford in November?

William Adair
Hi Michael, I'm not sure. It should be out by then but I don't know if any sellers will be stocking it. I live in Australia unfortunately, so Telford is well outside my maximum range 😢

William Adair
Added the large control wheel to the pilot's cockpit from soldered wire and heat curved sprue. I like the little brass hub in the middle 🙂

Skyhiker
You seem to have really good control over your soldering. What tools do you have? That control wheel is impressive.

gorby
The many years training to be a jeweler probably helps. 😄

William Adair
@Skyhiker I have an inexpensive soldering iron from an electronics store. It is nothing special, but the best thing I have is liquid soldering flux. Using that allows the solder to grab the surface and stick without requiring too much heat or flooding the area with solder.

@gorby Being a jeweller helped at first. But now I am finding that the modelmaking is helping me be a better jeweller! 👍

Alec K
Outstanding work! The book is on order 👍

William Adair
Wow, thank you Alec! Hopefully it will be in your mailbox soon 🙏
I added a few more pics. Test fitting the undercarriage and one of the prototype wheels.

Christian Bruer
Outstanding craftsmanship. I really like your tiny scratch built projects 👍

Michael Kohl
Me too.
But obviously he doesn't show how he did the wheels to prevent us from fainting. 😉

Skyhiker
I just don't get how its possible. Really man, you need to get a life or something. This shit is just way too good!

Mr D
Wow, what scale👌, l struggle to build a 1:72 without breaking of a tail wheel or antenna 🤣.
Really nice n interesting subject 👍👍

Skyhiker
Where do you get your blueprints?

William Adair
@Michael Kohl, I made an album about the wheel back in January, showing the stages of construction. Spoked wheel test, 1/144 | Album by F_IV
@Skyhiker, Windsock Datafiles provide the best drawings. I also use the 3-view drawings from the Wingnut Wings kit for some areas.

Zbynek Honzik
A masterpiece is being created here!!! Scratchbuild at this scale and this quality! Unbelievable! Bravo! 👏👏👏

bughunter
Great progress 👍
I have a kit in 1:48, but your build looks much better and has more details!

William Adair
Thank you, it's slowly coming along. Adding more details now that the main components are painted. It's always my favourite part of a build. 🙂

Mr D
Great " Little" project this one, brilliant work 👍👍

Treehugger
No idea. I am guessing any Academy Hercules kits, are re-branded kits from older molds, from Minicraft. I think Hasegawa has some 1:200 kits, but different scale, and might be mostly Japanese stuff.

James C
Awesome and thanks for sharing 👍

Mr D
Nice Quality work, very impressive...😁👍👍

Villiers de Vos
Very nice progress.

Doubtingmango
Watching