Vägg
Wall
June 28, 2024
Christian Lehmann
äger denna artikel
äger denna artikel
H.M.S. Hermes Carrier Air Group. 'Operation Corporate', 1982
Combat Decals 1:72
CD72-002 2012 Nytt verktyg 28 June, 19:11
June 13, 2024
Christian Lehmann
lade till ett nytt fotoalbum.
lade till ett nytt fotoalbum.
29 bilder
Acclamator Assault Ship1:2256
View into the top half of the hull. It includes the electronics and fibres to illuminate the command tower, torpedo laun...
Projekt: Acclamator Assault Ship
All comments (16) » 16 6 January, 19:47
Christian Lehmann
@ Markus: Youre right, the fibres limit the number of LED´s and the small fibres enable to create small dots of illumination like at the turbo lasers . The small IC´s are responsible for flickering and the others at the large bord provide constant current of 20 mA like an electronic pre resitor. Iam not sure if they are really needed but after some try and error they helped to avoid damaged LED´s. I tried to keep it simple because I am also not that familiar with electronics. Power source is a battery pack with 3x1,5V=4,5V batteries and everything is connectet parallel so that each part gets the same voltage.
@ Markus: Youre right, the fibres limit the number of LED´s and the small fibres enable to create small dots of illumination like at the turbo lasers . The small IC´s are responsible for flickering and the others at the large bord provide constant current of 20 mA like an electronic pre resitor. Iam not sure if they are really needed but after some try and error they helped to avoid damaged LED´s. I tried to keep it simple because I am also not that familiar with electronics. Power source is a battery pack with 3x1,5V=4,5V batteries and everything is connectet parallel so that each part gets the same voltage.
13 June, 04:39
Markus Helmers
the small fibres were obvious to me, just unsure about the big ones, but that's not a bad idea at all. You can trick so much with electronics. I recently got some LED remotes off ebay for like 2€ each and while I wasn't sure they'd work at all, it turns out they're not only capable of dimming the LEDs, but also come with a bunch of premade effects that you can even adjust the speed of. I was very impressed with them.
the small fibres were obvious to me, just unsure about the big ones, but that's not a bad idea at all. You can trick so much with electronics. I recently got some LED remotes off ebay for like 2€ each and while I wasn't sure they'd work at all, it turns out they're not only capable of dimming the LEDs, but also come with a bunch of premade effects that you can even adjust the speed of. I was very impressed with them.
13 June, 09:08
April 21, 2024
April 20, 2024
March 21, 2024
Christian Lehmann
äger denna artikel
äger denna artikel
Radiant VII consular-class cruiser
JPG Castings 1:350
. 21 March, 09:15
March 18, 2024
February 24, 2024
January 6, 2024
Christian Lehmann
lade till ett nytt fotoalbum.
lade till ett nytt fotoalbum.
30 bilder
Hounds Tooth1:144
The teeth symbols are decals, the red stripes are air brushed despite they are as decals in the kit. This makes weatheri...
Projekt: Hounds Tooth
All comments (7) » 7 12 December 2023, 21:08
Rando
Isn't this Bossk's ship? I remember that name from my Tales of the Bounty Hunters book. Extremely cool project!
Isn't this Bossk's ship? I remember that name from my Tales of the Bounty Hunters book. Extremely cool project!
6 January, 19:22
Christian Lehmann
@Rando: You´re right . I also put Bossk in the cockpit but unfortunately despite the large and plain windows illumination inside is poor. There are also one episode of "Clone Wars" where you can see this ship.
@Rando: You´re right . I also put Bossk in the cockpit but unfortunately despite the large and plain windows illumination inside is poor. There are also one episode of "Clone Wars" where you can see this ship.
6 January, 19:45
January 3, 2024
Christian Lehmann
lade till ett nytt projekt.
lade till ett nytt projekt.
1 3 January, 16:44
Christian Lehmann
I will try to light the engines bridge and some other areas. Because the kit is partly massive resin respectively fine 3D printed parts this will be a challenge.
I will try to light the engines bridge and some other areas. Because the kit is partly massive resin respectively fine 3D printed parts this will be a challenge.
3 January, 16:53
December 30, 2023
December 23, 2023
Christian Lehmann
markerade denna artikel som säljbar / sellable
markerade denna artikel som säljbar / sellable
Millennium Falcon Corellian Engineering Corporation YT-1300 Transport [Han Solo's Modified]
Fine Molds 1:72
SW-6 2006 Nytt verktyg Pris ej ännu levererat
23 December 2023, 19:45
December 16, 2023
December 11, 2023
August 6, 2023
Christian Lehmann
slutförde denna artikel
slutförde denna artikel
HMS Amazon Detail Set
Atlantic Models 1:600
ATEM60009 6 August 2023, 19:11
wnolder.php?lang=sv
2023-08-06 19:11:17
2011-10-03 15:32:48
10976
/ajax/wnolder.php?lang=sv&sd=2023-08-06 19:11:17&md=2011-10-03 15:32:48&filter=&w=10976
todo