Haber akışı
S M
yeni bir fotoalbüm ekledi.
yeni bir fotoalbüm ekledi.
27 3 September, 19:44
Tomislav Martan
bu ürünü siparişe göre işaretledi
bu ürünü siparişe göre işaretledi
Bf 110E Overtrees - Sprues only; no decals, instructions, mask or PE parts
Eduard 1:72
7091X 2015 Yeni kutu 24 November, 21:23
S M
bu öğeyi başlattı
bu öğeyi başlattı
F/A-18 HUG+ Hornet SUU-63 Plyon and BOL Dispenser RAAF & Finish AF hornets
Air-Graphic Models 1:72
AC-311 24 November, 21:18
Jakub Biganovsky
yeni bir fotoalbüm ekledi.
yeni bir fotoalbüm ekledi.
26 12 September, 06:45
Christoph Kunz
Watching with interesst.
I've done one landing gear yesterday, very fiddly.
Watching with interesst.
I've done one landing gear yesterday, very fiddly.
12 September, 07:13
Jakub Biganovsky
I am wondering how landing gear subassembly will fit; it will be next step.
I am wondering how landing gear subassembly will fit; it will be next step.
12 September, 08:00
J35J
The kit looks more "build friendly" than the DH88 Mikromir kit 1:48.
Looking forward to see the final result 👍🏻
The kit looks more "build friendly" than the DH88 Mikromir kit 1:48.
Looking forward to see the final result 👍🏻
27 September, 12:23
Jakub Biganovsky
Yep, Clear props brough realy high level of plastic kits. They are not same level as Tamyia/Eduard or...., but still very high.
Nice fitting and approximate details make a building friendly. Some small part surfaces keep milling prints due to local missing polishing of mould, but still fine.
Yep, Clear props brough realy high level of plastic kits. They are not same level as Tamyia/Eduard or...., but still very high.
Nice fitting and approximate details make a building friendly. Some small part surfaces keep milling prints due to local missing polishing of mould, but still fine.
27 September, 13:52
Michael Kohl
Following closely your progress as I have an eye on this kit. Nice additions you make and valuable experiences you share.
Following closely your progress as I have an eye on this kit. Nice additions you make and valuable experiences you share.
27 September, 14:00
Michael Kohl
Fit of the wing halfes is a problem indeed (bought the kit in the meantime), but I think you chose the harder route. Sanding/scraping down the contact areas between the upper and lower wing halfes should solve the problem without the need for extensive use of putty afterwards.
Fit of the wing halfes is a problem indeed (bought the kit in the meantime), but I think you chose the harder route. Sanding/scraping down the contact areas between the upper and lower wing halfes should solve the problem without the need for extensive use of putty afterwards.
24 November, 21:16
Vladimir Shidlovskiy
bu öğenin sahibi
bu öğenin sahibi
Ka-52 HUD exterior 3D decals (with 3D printed parts) for Zvezda
Quinta Studio 1:48
QP+48039 2024 Yeni araç 24 November, 21:10
/tr/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=tr
35
35
/tr/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo