Haber akışı
Cristian L
will attend
will attend
33. Modellbau-Ausstellung PMC Main-Kinzig
Gelnhausen
28. ve 29. Eylül 2024
28. ve 29. Eylül 2024
27 September, 13:21
Frank
bu öğenin sahibi
bu öğenin sahibi
Auto Salon Series
Morgan Plus 8 Roadster with 1:72 scale Pitts Special LS 1:16
C2002: 3000 (2) 1982 Yeni parçalar Çok konu (2)27 September, 13:19
Hrvoje
bu öğeyi istiyor
bu öğeyi istiyor
VF-201 Lone Star Hunters F-4N, F-14A
TwoBobs Aviation Graphics 1:48
48-285 2024 Yeni araç Çok konu (2)27 September, 13:15
Soeren R.
bu öğenin sahibi
bu öğenin sahibi
Macchi MC.200 Saetta Late Series (Serie IV-XXIII) interior 3D decals for Italeri/Tamiya
Quinta Studio 1:48
QD48467 2024 Yeni araç 27 September, 13:13
Soeren R.
bu öğenin sahibi
bu öğenin sahibi
Ka-52 Gun bay with 2A42 gun (3D-printed resin parts) for Zvezda kit
Quinta Studio 1:48
QT48025 2024 Yeni araç 27 September, 13:13
Soeren R.
bu öğenin sahibi
bu öğenin sahibi
Ka-52 HUD exterior 3D decals (with 3D printed parts) for Zvezda
Quinta Studio 1:48
QP+48039 2024 Yeni araç 27 September, 13:13
Sy Bar
yeni bir fotoalbüm ekledi.
yeni bir fotoalbüm ekledi.
14 Görüntüler
Bf110C-6Yeni: 27 September, 13:13 1:72
Hopefully one of these will sort the decals out
proje: Bf-110C-6
18 18 September, 11:53
Sy Bar
Was going to do the Battle of Britain version of this kit but I'm temped to have a go at some winter white wash and the wasp is cooler than the shark mouth 😎
Was going to do the Battle of Britain version of this kit but I'm temped to have a go at some winter white wash and the wasp is cooler than the shark mouth 😎
18 September, 11:56
István Szücs
I also have Bf-110 from the Airfix, I will build an Italian night fighter. The sprues are the same, so I'm watching!
I also have Bf-110 from the Airfix, I will build an Italian night fighter. The sprues are the same, so I'm watching!
18 September, 19:08
Sy Bar
Cheers guys.
I'm have a go at riveting, but going freehand as at this scale using tape was taking so long. I also not sure how much they will stand out on finish kit, but with the wonky line in parts they will probably bee seen from mars 🤣
Cheers guys.
I'm have a go at riveting, but going freehand as at this scale using tape was taking so long. I also not sure how much they will stand out on finish kit, but with the wonky line in parts they will probably bee seen from mars 🤣
22 September, 10:15
Sy Bar
Cheers #Guy 👍
#Skyhiker I found the fit to be good, I had a very slight gap at the front but think that was as much to do with me and the fitting of the pit (not the clearest instructions there). Every thing else was fine and the canopy was a good fit, I did change order of build slightly with the tail section I glued the rear piece to the body first then added the tail (after I'd added the stabilisers/rudders) this made more sense than the instructions 😁
Cheers #Guy 👍
#Skyhiker I found the fit to be good, I had a very slight gap at the front but think that was as much to do with me and the fitting of the pit (not the clearest instructions there). Every thing else was fine and the canopy was a good fit, I did change order of build slightly with the tail section I glued the rear piece to the body first then added the tail (after I'd added the stabilisers/rudders) this made more sense than the instructions 😁
24 September, 21:32
Sy Bar
Only issue I have with this kit are the decals. While they look great and are in perfect register, they have a large amount of film edging and are both thick and delicate at the same time🤪
Having a hard time getting them to settle into the panel lines etc. I usually just need to use micro sol but even ultimate extra strong is not have much effect. Going to have to wait till I get some Tamiya fixer, strong and extra strong hopefully one of these will help 🤞
Only issue I have with this kit are the decals. While they look great and are in perfect register, they have a large amount of film edging and are both thick and delicate at the same time🤪
Having a hard time getting them to settle into the panel lines etc. I usually just need to use micro sol but even ultimate extra strong is not have much effect. Going to have to wait till I get some Tamiya fixer, strong and extra strong hopefully one of these will help 🤞
24 September, 21:44
Soeren R.
bu öğenin sahibi
bu öğenin sahibi
MiG-17F / Lim-5, U.S.S.R., GDR Premium Special Edition
Ammo by Mig Jimenez 1:48
A.MIG-8512 2023 Yeni parçalar 27 September, 13:12
J D
yeni bir fotoalbüm ekledi.
yeni bir fotoalbüm ekledi.
41 Görüntüler
Panzer III Ausf. J (DAK Version with L/60 Barrel & Spaced Armor)1:35
Figure and accessories have been added.
Project could be eventually closed after couple of years ?
16 9 July 2022, 07:06
J D
Thx for your comment, Doubtingmango.
The new Academy 13531 Pz. III J launched in 2021 was an excellent kit.
Unlike the old kits produced by Academy in last century, there is no fitting problem and most details are presented nicely in this kit. The instruction manual is colorized, quite clear and could be read & understood easily even for the beginners. Highly recommended and great substitution for Dragon 6394 & 6543.
One of the drawbacks are the tracks of kit. Academy mistakenly offers the type 5B tracks, while actually Pz. III J in African campaign equipped type 3A tracks.
Thx for your comment, Doubtingmango.
The new Academy 13531 Pz. III J launched in 2021 was an excellent kit.
Unlike the old kits produced by Academy in last century, there is no fitting problem and most details are presented nicely in this kit. The instruction manual is colorized, quite clear and could be read & understood easily even for the beginners. Highly recommended and great substitution for Dragon 6394 & 6543.
One of the drawbacks are the tracks of kit. Academy mistakenly offers the type 5B tracks, while actually Pz. III J in African campaign equipped type 3A tracks.
20 September, 14:14
/tr/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
search-solr.php?lang=tr
35
35
/tr/search.php?q=*&page=newsfeed&fkSECTION[]=Newsfeed
35
todo